Lindy 40846 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Lindy 40846 (4 pagina's) in de categorie Projector accessoire. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - FIRST EDITION (November 2010)
Modular Projector Brackets
Manual
English
LINDY No. 40846, 40847, 40848 & 40849
www.lindy.com
User Manual
Thank you for purchasing the LINDY modular solution for mounting projectors in your
home, office or AV multimedia setup. Both products are universal and can support
most projectors up to a weight of 11.5Kg. The brackets and poles all have the same
black finish and also have the added benefit of a cable management system built in to
the poles.
This manual will show you how to assemble and adjust both types of bracket using
either the long or short pole. Please take note of the maximum weights supported by
the brackets to avoid any damage to your installation or equipment.
Both the long and short poles attach to the ceiling or wall in the same manner.
40846: 73 to 123cm from the wall/ceiling 31 to 41cm from the wall/ceiling 40847:
Each pole has its own cable management system. Using a conduit up the centre of
the pole you can hide unsightly power and video cables from view.
The diagram below shows how the cable is fed through the pole and can either go up
through the ceiling or out through the side of the cable cover for a tidier appearance.
Assembling the “box” bracket: 40848
The “box” bracket comes with the following pieces:
73
123cm
31
41cm
User Manual
Note: you will need to adjust the size of the “box” bracket by loosening and
tightening nuts (C) depending on the size of your projector.
Step 1
Attach 2 foam strips (G) to the underside of
the main bracket as shown. This will
protect your projector from scratching
against the metal surfaces. Connect the 4 L
pieces (D) to each corner of the main
bracket using nuts (C), washers (B) and
spanner (H).
Step 2
Attach the foam strip (G) as shown, to
bottom bracket (E). Using nuts (C) and
washers (B), attach the first part of the
bottom bracket (E) to the L piece (D).
Step 3
Attach the last foam strip (G) to the
second bottom bracket (F). Then attach
(F) to the L pieces (D) using the nuts (C)
and washers (B). The remaining nuts and
washers are to connect the two bottom
brackets (E) as shown.
Step 4
After attaching the main bracket to the
pole you can adjust the length of the
pole and lock it with screws (A).
Adjusting the bolt with the spanner (I)
will allow you to tilt and adjust your
projector to fit your requirements.


Product specificaties

Merk: Lindy
Categorie: Projector accessoire
Model: 40846
Kleur van het product: Zwart
Diepte: 1230 mm

Heb je hulp nodig?

Als je hulp nodig hebt met Lindy 40846 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Projector accessoire Lindy

Handleiding Projector accessoire

Nieuwste handleidingen voor Projector accessoire

Chief

Chief SLM248 Handleiding

18 November 2024
Chief

Chief SLM251 Handleiding

17 November 2024
Chief

Chief SLM255 Handleiding

17 November 2024
Chief

Chief SLM293 Handleiding

17 November 2024
Chief

Chief SLM3000 Handleiding

17 November 2024
Chief

Chief RPMAU Handleiding

17 November 2024
Chief

Chief SLM230 Handleiding

17 November 2024
Chief

Chief WM2I Handleiding

17 November 2024