Liftmaster MHS5011U Handleiding

Liftmaster Niet gecategoriseerd MHS5011U

Lees hieronder de πŸ“– handleiding in het Nederlandse voor Liftmaster MHS5011U (24 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 150 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/24
OWNER'S MANUAL
MODELS:
LGJ & MGJ
INDUSTRIAL DUTY DOOR OPERATOR
NOT FOR RESIDENTIAL USE
LISTED DOOR OPERATOR
41B6
Serial #
(located on electrical box cover)
Installation Date
Wiring Type
2 YEAR WARRANTY
2
MOTOR
TYPE: .................................Intermittent Duty
HORSEPOWER: MGJ:................ 1/2Hp 1 or 3 Phase
LGJ: 1/4 Hp 1 Phase
SPEED: MGJ:............................... 1050 RPM
LGJ: 1725 RPM
VOLTAGE: .........................MGJ: 115, 60HZ, 1Ph
230V, 50 or 60Hz, 3Ph
230V, 60Hz, 1Ph
380V, 50Hz, 3Ph
460V, 60Hz, 3Ph
LGJ: 115V, 60Hz, 1Ph
CURRENT: See motor nameplate
MECHANICAL
DRIVE REDUCTION: .... . . . . . . . . . . . 40:1 Reduction
(Heavy duty wormgear-in-oil-bath speed reducer)
OUTPUT SPROCKET: ..........Size #41
DOOR SPEED: MGJ:. . . . . . . . . . 1Ph, 23RPM
3Ph, 39RPM
LGJ: .1Ph, 43RPM
BEARINGS: .................Heavy duty wormgear-in-oil-bath
speed reducer.
SAFETY
DISCONNECT :.......................Floor level disconnect for
emergency manual door operation.
REVERSING EDGE: ...............(Optional) Electric or
pneumatic sensing device attached to the bottom edge
of door
A REVERSING EDGE IS STRONGLY RECOMMENDED
FOR
ALL
COMMERCIAL OPERATOR INSTALLATIONS.
REQUIRED
WHEN THE 3 BUTTON CONTROL STATION
IS OUT OF SIGHT OF DOOR OR ANY OTHER
CONTROL (AUTOMATIC OR MANUAL) IS USED.
SPECIFICATIONS
ELECTRICAL
TRANSFORMER:.............24VAC
CONTROL STATION: .....NEMA 1 three button station.
OPEN/CLOSE/STOP
WIRING TYPE: MGJ: B2-C2 (Factory Shipped)
LGJ: G2 (Factory Shipped)
See pages 13 and 14 for optional control settings and
operating modes.
LIMIT ADJUST:................Linear driven, fully adjustable
screw type cams. Adjustable to 24 feet.
7.50”
7.00”
11.00”
9.25”
LGJ WEIGHTS AND DIMENSIONS
HANGING WEIGHT: 80-110 LBS..........
10.50”
11.05”
MOUNTING DIMENSIONS
3.00”
5.50”
4.75”
8.90”
7.90”
1.97”
10.88”
4.50”
2.25”
.98”
1.96”
MOUNTING DIMENSIONS
MGJ WEIGHTS AND DIMENSIONS
HANGING WEIGHT: 80-110 LBS..........
3
FIGURE 1
Shaft Support Bracket
with Bearing (Not Supplied)
Door Sprocket
TO AVOID DAMAGE TO DOOR AND OPERATOR,
MAKE ALL DOOR LOCKS INOPERATIVE. SECURE
LOCK(S) IN "OPEN" POSITION.
IF THE DOOR LOCK NEEDS TO REMAIN
FUNCTIONAL, INSTALL AN INTERLOCK SWITCH.
DO NOT CONNECT ELECTRIC POWER UNTIL
INSTRUCTED TO DO SO.
KEEP DOOR BALANCED. STICKING OR BINDING
DOORS MUST BE REPAIRED. DOORS, DOOR
SPRINGS, CABLES, PULLEYS, BRACKETS AND
THEIR HARDWARE MAY BE UNDER EXTREME
TENSION AND CAN CAUSE SERIOUS PERSONAL
INJURY. CALL A PROFESSIONAL DOOR
SERVICEMAN TO MOVE OR ADJUST DOOR
SPRINGS OR HARDWARE.
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION WARN
WARN
WARN
WARNWARNING
ING
ING
INGING
SITE PREPARATIONS
It is imperative that the wall or mounting surface
provide adequate support for the operator.
This surface must:
a) Be rigid to prevent play between operator and
door shaft.
b) Provide a level base.
c) Permit the operator to be fastened securely and
with the drive shaft parallel to the door shaft.
The safety and wear of the operator will be adversely
aected if any of the above requirements are not met.
For metal buildings, fasten 2” x 2” x 3/16” (or larger)
angle iron frames to the building purlins. For proper
spacing, retain .2.75” between for model MGJ, butt
purlins together for model LGJ. See Figure 1.
OPERATOR PREPARATION
IMPORTANT SAFETY NOTES
2.75 for MGJ, butt together for LGJ
Model LGJ: Shipped from the factory for right hand mounting, refer to preparation instructions on page 4 for
Left hand mounting.
Model MGJ: Shipped from the factory for either left hand or right hand mounting. Refer to the last digit in the
model number for handing of your unit. If necessary, model MGJ may also be ξ‹ˆeld modiξ‹ˆed to
accommodate opposite handing. Refer to the conversion instructions below and on page 4.
KEYS
SPRING
DISC
HUB
E RING
SPROCKET
YOKE
BRACKET
SHAFT
DISC
LEVER
MGJ OPPOSITE HANDING PREPARATIONS
1. Remove Disconnect Assembly Components
Remove the master link from the limit chain, remove
the chain and set it aside.
Remove the two E Rings securing the sprocket on
the gear reducer shaft. Remove the screws securing
the yoke to the disconnect shaft, set the yoke aside.

Product specificaties

Merk: Liftmaster
Categorie: Niet gecategoriseerd
Model: MHS5011U

Heb je hulp nodig?

Als je hulp nodig hebt met Liftmaster MHS5011U stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Liftmaster

Liftmaster

Liftmaster CAPXLV2MC Handleiding

5 Augustus 2024
Liftmaster

Liftmaster BG770 Handleiding

8 Juli 2024
Liftmaster

Liftmaster LMHNTG Handleiding

8 Juli 2024
Liftmaster

Liftmaster SL585 Handleiding

11 Juni 2024
Liftmaster

Liftmaster SL590 Handleiding

11 Juni 2024
Liftmaster

Liftmaster BG3000 Handleiding

11 Juni 2024
Liftmaster

Liftmaster CAPXSTKPL Handleiding

9 Juni 2024
Liftmaster

Liftmaster BG790 Handleiding

9 Juni 2024
Liftmaster

Liftmaster 64LM Handleiding

27 Mei 2024
Liftmaster

Liftmaster CAPXSHOOD Handleiding

8 December 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Festo

Festo VPPI Handleiding

21 November 2024
Festo

Festo VAVE-P17-TP-5YL1-P Handleiding

21 November 2024
Festo

Festo SD-SUB-D-BU9 Handleiding

21 November 2024
Festo

Festo SAMH-F12-MK Handleiding

21 November 2024
Festo

Festo SFAB Handleiding

21 November 2024
Festo

Festo SFAH Handleiding

21 November 2024
Festo

Festo DRRD-12 Handleiding

21 November 2024
Festo

Festo SDE3 Handleiding

21 November 2024
Festo

Festo SFTE Handleiding

21 November 2024
Festo

Festo CRVZS-5 Handleiding

21 November 2024