Liftmaster 64LM Handleiding

Liftmaster Niet gecategoriseerd 64LM

Lees hieronder de ๐Ÿ“– handleiding in het Nederlandse voor Liftmaster 64LM (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 48 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
To prevent possible SERIOUS INJURY or
DEATH from a moving gate or garage door:
โ€ข ALWAYS keep remote controls out of
reach of children. NEVER permit children
to operate, or play with remote control
transmitters.
โ€ข Activate gate or door ONLY when it can be
seen clearly, is properly adjusted, and
there are no obstructions to door travel.
โ€ข ALWAYS keep gate or garage door in sight
until completely closed. NEVER permit
anyone to cross path of moving gate or
door.
INTRODUCTION
This product is for use with gate operators, commercial door operators and any LiftMaster
ยฎ product
that uses a 390 MHz fixed code. The single-button remote control will activate one device, the
2-button remote control will activate up to 2 devices, and the 3-button remote control will activate
up to 3 devices.
Models 61LM & 61LMC
Models 62LM & 62LMC
Models 33LM, 33LMC
63LM, & 63LMC
Models 64LM & 64LMC
Locate the dip switches on your remote control
BEFORE YOU BEGIN
Single-Button and 3-Button Remote Controls:
Slide the battery cover open to access the dip
switches in the remote control.
2-Button Remote Control:
The 2-button remote control has two sets of
dip switches.
Slide the battery cover open to access the dip
switches for the smooth button. Remove the
screw on the back of the remote control and
remove the cover by pressing the tab. This will
access the dip switches for the ribbed button.
3-Button Mini Remote Control:
The large top button is recommended for use with
a garage door opener and/or light control product.
The other push buttons can be used to operate
another garage door opener and/or light control
product.
Access the dip switches by turning the remote
over and removing the back of the case. Be
careful to avoid moving circuit board components.
+
0
โ€“
123456789
+
0
โ€“
123456789
+
0
โ€“
123456789
+
0
โ€“
123456789
Tab
1
Single and 3-Button Remote Controls
2-Button Remote Controls
Mini Remote Controls
WARNING: This product can expose you to chemicals including lead, which are known to
the State of California to cause cancer or birth defects or other reproductive harm. For more
information go to www.P65Warnings.ca.gov
PROGRAMMING
1
1
Press and release the Smart/Learn button
on your product. The LED will light.
2
2
Within 30 seconds press and hold the
button on the remote control that you
wish to activate your product.
Programming is complete.
Repeat the steps above for each button and/or
remote control you would like to program.
Programming with Smart/Learn button
2
Programming the remote control to an
existing remote control
Locate the dip switches in the new and old
remote controls. Place remote controls side by
side and set the dip switches in the remote
controls to matching positions (+,0,-).
Programming a 3-button remote control
When programming a single or 2-button remote
control to a 3-button remote control it is very
important to set dip switch #1 to the correct
position. The dip switch in the single or 2-button
remote control MUST correspond to the buttons
on the 3-button remote control as shown.
Example: If you are programming a
single-button remote control to the middle button
on the 3-button remote control, dip switch #1 in
the single-button remote control MUST be set to
โ€œ0โ€ in order for both buttons to work.
+
0
โ€“
1 2 3 4 5 6 7 8 9
+
0
โ€“
1 2 3 4 5 6 7 8 9
=
+
0
โ€“
1 2 3 4 5 6 7 8 9
+
0
โ€“
123 456 789
=
2 3 4 5 6 7 8 9
+
0
โ€“
1 2 3 4 5 6 7 8 9
=
+
0
โ€“
1
+0
-
New Remote Control
Dip Switch Settings
From Product
3-Button
Remote Control
Single or 2-Button
Remote Control
Dip switch #1 must
correspond to the 3-button
remote control buttons
Existing Remote Control
New Remote
Control
12
Smart/Learn Button
Programming the remote control
without an existing remote control
Set the dip switches in the remote controls to
any position you want (+,0,-).
+
0
โ€“
1 2 3 4 5 6 7 8 9
New Remote Control
Use a pen or screwdriver to slide the dip switches.
Check the dip switch settings on the back of
your product.
Use a pen or screwdriver to slide the dip
switches in the remote control to match the
dip switches on the back of the product.
When the dip switches have been set press the remote
control button to activate your product.
Programming with dip switches
PROGRAMMING MODEL 33LMC ONLY
Install the control station and receiver where the door is visible, but away from the door and its
hardware. When a receiver is used to activate a commercial door opener, a reversing edge MUST
be installed on the bottom of the door. Failure to install a reversing edge under these
circumstances may result in SERIOUS INJURY or DEATH to persons trapped beneath the door.
Model 33LM 3-button remote controls can also be used with a 423LM 3-channel receiver and a
3-button door control to activate a commercial door operator in OPEN, CLOSE, and STOP mode.
1Use a screwdriver to pry open the receiver
cover.
2Verify that the slide switch on receiver is
set to the N.C. position (other wise the
commercial door operator will not
operate).
4Within 30 seconds press and release the
red button on the remote control. The red
button is now programmed for CLOSE
mode.
NOTE: If the remote control button is not
pressed within 30 seconds, the LED next
to the selected Smart/Learn button will
turn OFF. In that case, press the
Smart/Learn button again to repeat
programming.
3Press and release the Smart/Learn button
labeled โ€œAโ€ on the receiver. The adjacent
LED will flash.
5
Repeat the steps 3-4 above with the yellow button on the remote control and the receiver
Smart/Learn button โ€œBโ€ to program the CLOSE mode; and again with the green button on the remote
control and the receiver Smart/Learn button โ€œCโ€ to program the OPEN mode.
Replace the receiver cover.
3
1
3
4
5
โ€œAโ€ Smart/Learn Button
2N.C.
Slide
Switch

Product specificaties

Merk: Liftmaster
Categorie: Niet gecategoriseerd
Model: 64LM

Heb je hulp nodig?

Als je hulp nodig hebt met Liftmaster 64LM stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Liftmaster

Liftmaster

Liftmaster CAPXLV2MC Handleiding

5 Augustus 2024
Liftmaster

Liftmaster BG770 Handleiding

8 Juli 2024
Liftmaster

Liftmaster LMHNTG Handleiding

8 Juli 2024
Liftmaster

Liftmaster SL585 Handleiding

11 Juni 2024
Liftmaster

Liftmaster SL590 Handleiding

11 Juni 2024
Liftmaster

Liftmaster BG3000 Handleiding

11 Juni 2024
Liftmaster

Liftmaster CAPXSTKPL Handleiding

9 Juni 2024
Liftmaster

Liftmaster BG790 Handleiding

9 Juni 2024
Liftmaster

Liftmaster 64LM Handleiding

27 Mei 2024
Liftmaster

Liftmaster CAPXSHOOD Handleiding

8 December 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Xblitz

Xblitz R8 Power Charge Handleiding

3 December 2024
Xblitz

Xblitz R4 Power Handleiding

3 December 2024
Franke

Franke Urban UBG 610-78 Handleiding

3 December 2024
Franke

Franke ANX211RHD Handleiding

3 December 2024
Franke

Franke ANX220 Handleiding

3 December 2024
Dell

Dell NX3330 Handleiding

3 December 2024
Dell

Dell PowerConnect B-DCX-4s Handleiding

3 December 2024
Hager

Hager AKB83000701 Handleiding

3 December 2024
Hager

Hager AKB81500402 Handleiding

3 December 2024
Hager

Hager AKBA1500401V Handleiding

3 December 2024