Liftmaster KPW250 Handleiding

Liftmaster Niet gecategoriseerd KPW250

Lees hieronder de 📖 handleiding in het Nederlandse voor Liftmaster KPW250 (20 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/20

KPW5 KPW250

OVERVIEW

Wireless Commercial Keypads are security keypads and should be programmed to ONE operator.

The Wireless Commercial Keypad comes with one 9V Lithium battery, instructions, and two keys. A wireless signal is

transmitted when a valid 4-digit PIN and the # key is pressed. A long tone will sound. The keypad backlight will illuminate for

15 seconds when any key is pressed. If an invalid PIN or partial PIN is accidentally entered, an error tone will sound. The

Wireless Commercial Keypad is compatible with the brands of commercial door and gate operators listed in the table below.

Wireless Commercial Keypad

Models KPW5 and KPW250

MODEL FREQUENCY AND ENCRYPTION PIN CAPACITY

KPW5 LiftMaster Security+ 2.0® Default

Tri-band 390 MHz, 315 MHz, and 310 MHz

Up to 5 permanent PINs and

Up to 10 unique temporary PINs

KPW250 LiftMaster Security+ 2.0® Default

Tri-band 390 MHz, 315 MHz, and 310 MHz

Up to 250 permanent PINs and

Up to 10 unique temporary PINs

LiftMaster Security+® 315 MHz

LiftMaster Security+® 390 MHz

Linear Multi-Code 300 MHz

Speciﬁ cations

Power ..................................................................................................................................................................... 9V Lithium battery

Operating temperature range .............................................................................................................. -4°F to 140°F (-20°C to 60°C)

Storage and shipping temperature range .........................................................................................-40°F to 140°F (-40°C to 60°C)

Enclosure ..............................................................................................................................................................................NEMA 3R

INSTALLATION

1. Choose a mounting location suitable for your application such as a wall, flat surface, or a pedestal with a 3" x 3" mounting

pattern (LiftMaster gooseneck pedestal post models PED42 or PED64). Locate the keypad at least 6 feet (1.8 m) away

from any moving part of the gate and where the user cannot reach over, under, around or through the gate to operate the

controls. The mounting location needs to be in line of sight of the moving gate.

2. Unlock and remove the faceplate from the mounting plate.

3. Mount the mounting plate to the desired surface and secure with 1/4" screws or bolts (not provided).

4. Remove the battery cover using a Phillips screw driver. Install the battery (provided) and re-install inner cover.

5. Reattach the faceplate to the mounting plate and lock with the key.

To prevent possible SERIOUS INJURY or DEATH from a moving gate or door:

• User activation controls MUST be located at least 6 feet (1.8 m) away from ANY moving part of the gate and where the

user cannot reach over, under, around or through the gate to operate the controls.

• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with remote controls.

• Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

• ALWAYS keep gate or door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.

Battery

Mounting plate

Faceplate

Battery Cover

WARNING: This product can expose you to chemicals including lead, which are known to the State of California to

cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

Program to LiftMaster Operator

NOTE: The Master Code and a PIN need to be set before the gate operator can be programmed. See Basic Programming.

KPW5 - The frequency and encryption are set at the factory. Proceed to Step 4.

KPW250 - The frequency and encryption are set at the factory for (tri-band 310, 315, and 390 MHz) LiftMaster Security+ 2.0

operators. Proceed to Step 4.

For LiftMaster Security+ (315 MHz or 390 MHz), the frequency and encryption need to be set.Proceed to Step 1.

1. Enter program mode: * (Master Code) #.

2 Set frequency and encryption (KPW250 only):

• LiftMaster Security+ 315 MHz - Press . A long tone will sound.03 # 2 #

• LiftMaster Security+ 390 MHz - Press . A long tone will sound.03 # 3 #

• To reset factory default - Press . A long tone will sound.03 # 1 #

3. Exit Program Mode: * * #.

4. Press the Learn Button on the operator.

5. Within 30 seconds - Enter a valid then press #. A long tone will sound.4-digit PIN

PROGRAM TO OPERATOR

BASIC PROGRAMMING

The Wireless Commercial Keypad must be put into programming mode prior to any of the programming steps below unless

otherwise indicated. The keypad backlight will remain on if the product is in programming mode. While in programming

mode, if an invalid code is entered, an error tone will sound, but the keypad will remain in programming mode. After 60

seconds of inactivity, the keypad will exit the programming mode. The 6-digit Master Code is used to prevent unauthorized

access to the system. A Master Code is required (factory default code: 888888) to operate the Wireless Commercial Keypad. It

is highly recommended to change and record your unique Master Code.

Programming Step Keystroke Combination Indicator

1. Enter program mode * (Master Code) # Long tone

2. Update Master Code 09 # (New 6-digit Code) # (New 6-digit Code) # Long tone

3. Exit Program Mode * *

#Keypad backlight will turn off

Programming Step Keystroke Combination Indicator

1. Enter program mode * (Master Code) # Long tone

2. Set new pin 01 # (New 4-digit PIN) # Repeat (new 4-digit PIN) #Long tone

3. Exit Program Mode * *

#Keypad backlight will turn off

NOTE: An error tone will sound if the maximum number of PINs is exceeded or if user tries to program a PIN already

programmed in the memory.

Set Master Code

Program a PIN

Product specificaties

Merk:	Liftmaster
Categorie:	Niet gecategoriseerd
Model:	KPW250

Heb je hulp nodig?

Als je hulp nodig hebt met Liftmaster KPW250 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Liftmaster

Liftmaster CAPXLV2MC Handleiding

5 Augustus 2024

Liftmaster BG770 Handleiding

8 Juli 2024

Liftmaster LMHNTG Handleiding

8 Juli 2024

Liftmaster SL585 Handleiding

11 Juni 2024

Liftmaster SL590 Handleiding

11 Juni 2024

Liftmaster BG3000 Handleiding

11 Juni 2024

Liftmaster CAPXSTKPL Handleiding

9 Juni 2024

Liftmaster BG790 Handleiding

9 Juni 2024

Liftmaster 64LM Handleiding

27 Mei 2024

Liftmaster CAPXSHOOD Handleiding

8 December 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Protector AS-5030.3 V2 Handleiding

21 December 2024

Sabrent AU-MMCW Handleiding

21 December 2024

Sabrent AU-2X35 Handleiding

21 December 2024

Sabrent CB-RS232 Handleiding

21 December 2024

Owon 500W Handleiding

21 December 2024

Owon 300W Handleiding

21 December 2024

Sabrent SB-RKTQ4-1TB Handleiding

21 December 2024

Sabrent SB-RKTQ-1TB Handleiding

21 December 2024

Sabrent SB-ROCKET-1TB Handleiding

21 December 2024

Sabrent SB-HTSS Handleiding

21 December 2024