Liftmaster HPH1 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Liftmaster HPH1 (46 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 57 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/46
HPH1
High Performance Hoist
INSTALLATION MANUAL
LiftMaster
300 Windsor Drive
Oak Brook, IL 60523
ULUS
C
LISTED
HPH1, 1.25 HP (120V/240V Single Phase & 230V Three Phase)
(460V/575V Three Phase, via stepdown transformer accessories)
2
TO REDUCE THE RISK OF SEVERE INJURY OR DEATH:
IMPORTANT INSTALLATION INSTRUCTIONS
1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND
INSTRUCTIONS.
2. Install door operator ONLY on a properly balanced and
lubricated door. An improperly balanced door may NOT
reverse when required and could result in SEVERE INJURY
or DEATH.
3. ALL repairs to cables, spring assemblies and other hardware
MUST be made by a trained door systems technician BEFORE
installing an operator.
4. Disable ALL locks and remove ALL ropes connected to a
door BEFORE installing an operator to avoid entanglement.
5. Install an operator, a minimum of 8 feet (2.44 m) from the
floor.
6. NEVER connect a door operator to a power source until
instructed to do so.
7. NEVER wear watches, rings or loose clothing while installing
or servicing an operator. They could be caught in the door or
operator mechanisms.
8. Install a control station and/or controller:
within sight of the door
out of reach of children and at a minimum height of 5 feet
(1.5 m) above floors, landings, steps, or any other
adjacent walking surface
away from ALL moving parts of the door
9. Install the control station far enough from the door to
prevent the user from coming in contact with the door while
operating the controls.
10. Install the entrapment warning placard on the wall next to
the control station in a prominent location, visible from the
door.
11. Instruct the end user on the operation of the manual
release.
12. Upon completion of installation, test the entrapment
protection device(s).
13. SAVE THESE INSTRUCTIONS.
When you see these Safety Symbols and Signal Words on the
following pages, they will alert you to the possibility of serious
injury death or if you do not comply with the warnings that
accompany them. The hazard may come from something
mechanical or from electric shock. Read the warnings carefully.
Mechanical
Electrical
IMPORTANT NOTES:
BEFORE attempting to install, operate or maintain the
commercial door operator, you must read and fully understand
this manual and follow all safety instructions.
DO NOT attempt repair or service of a commercial door
operator unless you are an Authorized Service Technician.
A commercial door operator should only be installed on a
properly balanced door only. Ensure door is properly balanced
prior to installation.
SAFETY INFORMATION
ENTRAPMENT PROTECTION DEVICES:
Monitored Entrapment Protection
Monitored photoelectric sensors and/or door edge sensors are
required for any momentary contact to close modes of operation.
See page 18 for additional information. Refer to the accessories
page 42, ‘Entrapment Protection Devices’ for available options.
When you see this Signal Word on the following pages, it will
alert you to the possibility of damage to your door and/or the
door operator if you do not comply with the cautionary
statements that accompany it. Read them carefully.
WARNING: This product can expose you to chemicals
including lead, which are known to the State of California to
cause cancer or birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov.
3
TABLE OF CONTENTS
SAFETY INFORMATION 2
OPERATOR 4-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Carton Inventory ............................... 4
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5
Operator Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 6
INSTALLATION .................................7-18
Preparing the Operator for Mounting. . . . . . . . . . . . . . . . 7
Mounting the Operator. . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing the Cable Tension Monitor . . . . . . . . . . . . . . . . 9
Connect the Hoist Release . . . . . . . . . . . . . . . . . . . . . . . 10
Low-Voltage Wiring of the Powerhead. . . . . . . . . . . . . . 11
Wiring the Incoming Power to the Powerhead . . . . . . . 12
Wiring the 3-Phase Stepdown Transformer. . . . . . . . . . 13
Mounting the Controller. . . . . . . . . . . . . . . . . . . . . . . . . 14
Controller Specifications . . . . . . . . . . . . . . . . . . . . . . . . 15
Wiring the Controller . . . . . . . . . . . . . . . . . . . . . . . . .16-17
Wiring the Monitored Entrapment Protection . . . . . . . . 18
Installing the Monitored Light Curtain . . . . . . . . . . . . . . 19
PROGRAMMING 20-33. . . . . . . . . . . . . . . . . . . . . . . . . .
Menus ....................................20-22
Reset Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Operating Mode Overview . . . . . . . . . . . . . . . . . . . . . . . 24
Configuring the Relay Adapter . . . . . . . . . . . . . . . . . . . . 25
Auxiliary Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Radio, myQ® Devices, & Remotes . . . . . . . . . . . . . . . . . 26
Erasing Programmed Devices . . . . . . . . . . . . . . . . . . . . 26
Connecting to myQ® Smart Facility . . . . . . . . . . . . . . . . 27
Provisioning Wi-Fi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Determine and Set Operating Mode. . . . . . . . . . . . . .28-33
TROUBLESHOOTING 34-36. . . . . . . . . . . . . . . . . . . . . . .
MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Life of Operator Feature . . . . . . . . . . . . . . . . . . . . . . . . . 37
How to Order Repair Parts. . . . . . . . . . . . . . . . . . . . . . . 37
CONTROLLER WIRING DIAGRAM . . . . . . . . . . . . . . . . .38
ACCESSORY WIRING DIAGRAM . . . . . . . . . . . . . . . . . .39
OPERATOR DIMENSIONS . . . . . . . . . . . . . . . . . . . . . .40
REPAIR PARTS & SERVICE KITS . . . . . . . . . . . . . . 41-42
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
CONNECTIVITY
myQ® Smart Facility Access Technology enables secure monitoring and control of door operators and other
myQ® Smart Facility Access devices with a smartphone, tablet or computer.
Alerts can be received as email notifications, ensuring the status of a commercial door.
SAFETY AND SECURITY
Security+ 2.0® – with every press of the button, a new code is sent to the commercial door operator, ensuring a door will only open
for the remote control programmed.
UL 325 requires all commercial door operators to be either constant pressure to close or be equipped with a primary external monitored
entrapment protection device.
LiftMaster® is the leading brand of professionally installed commercial door operators and access control products for businesses
worldwide. We are committed to quality products, innovative designs and comprehensive services which exceed our Customers
expectations.


Product specificaties

Merk: Liftmaster
Categorie: Niet gecategoriseerd
Model: HPH1

Heb je hulp nodig?

Als je hulp nodig hebt met Liftmaster HPH1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Liftmaster

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Festo

Festo VPPI Handleiding

21 November 2024
Festo

Festo SFAB Handleiding

21 November 2024
Festo

Festo SFAH Handleiding

21 November 2024
Festo

Festo DRRD-12 Handleiding

21 November 2024
Festo

Festo SDE3 Handleiding

21 November 2024
Festo

Festo SFTE Handleiding

21 November 2024
Festo

Festo CRVZS-5 Handleiding

21 November 2024