Liftmaster CPS-OPEN4 Handleiding

Liftmaster Niet gecategoriseerd CPS-OPEN4

Lees hieronder de 📖 handleiding in het Nederlandse voor Liftmaster CPS-OPEN4 (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

LIFTMASTER® PROTECTOR SYSTEM

MODEL CPS-OPEN4

APPLICATION

LiftMaster® Protector System model CPS-OPEN4 is a monitored entrapment protection device for use with sectional and rolling doors. This device is

compatible with LiftMaster Heavy, Standard, and Medium Duty Logic (post 2010), FDC, FCL, FDOA, FDOB, and Egress Commercial Door operators. This

device may be installed in areas exposed to rain or moisture. These images in this document are for reference only and your product may look different.

SPECIFICATIONS

Power Consumption: Max. 50mA

Supply Voltage: 6 to 40 Vdc

Operating Temperature: -13°F to 165°F (-25°C to 73°C)

NEMA4 rating

CARTON INVENTORY

Photoelectric sensors (transmitter and receiver), mounting brackets (2), hardware, and instructions

LIFTMASTER® PROTECTOR SYSTEM

IMPORTANT INFORMATION ABOUT THE PHOTOELECTRIC SENSOR

Be sure power to the operator is disconnected.

When properly connected and aligned, the photoelectric sensor will detect an obstruction in the path of its beam. If an obstruction breaks the beam while

the door is closing, the operator will stop and typically reverse to the full open position.

The transmitter must be installed so that it faces the receiver across the entrapment zone, no more than 6" (15 cm) above the ﬂ oor for a door. Minimum

installation width of 3 feet (.91 m) and maximum width of 45 feet (13.7 m).

The brackets must be securely fastened to a solid surface such as the wall framing. If installing in masonry construction, add a piece of wood at each

location to avoid drilling extra holes in masonry if repositioning is necessary.

The invisible light beam path must be unobstructed. No part of the door (or door tracks, springs, hinges, rollers or other hardware) may interrupt the

beam while the door is closing.

ENTRAPMENT ZONES

Make sure the brackets are aligned so the photoelectric sensors will face each other across the entrapment zone as illustrated.

ENTRAPMENT ZONE FOR COMMERCIAL DOOR APPLICATION

To prevent possible SERIOUS INJURY or DEATH from a closing door:

• Be sure to DISCONNECT POWER to the operator BEFORE installing the photoelectric sensor.

• The door MUST be in the fully opened or closed position BEFORE installing the LiftMaster

® Monitored Entrapment Protection device.

• Correctly connect and align the photoelectric sensor.

• Install the photoelectric sensor beam NO HIGHER than 6" (15 cm) above the ﬂ oor.

• LiftMaster® Monitored Entrapment Protection devices are for use with LiftMaster

® Commercial Door. Use with ANY other product voids the

warranty.

• Entrapment protection devices MUST be installed per the operator owner's manual for each Entrapment Zone.

Photoelectric

Sensor

Entrapment Zone Invisible Light Beam

Protection Area

Photoelectric

Sensor

6" (15 cm) max. above the

ﬂoor and away from the door

6" (15 cm) max. above the

ﬂoor and away from the door

Facing the door from inside the building

(Installation procedures are the same for all door types)

GARAGE DOOR

Secondary protection ONLY

Primary Monitored Entrapment

18" (46 cm) min.

48" (122 cm) min.

R S

S R

R S

S R

R S

S R

DOOR #1 DOOR #2 DOOR #3

R S = Receiving Sensor = Sending Sensor

24" (61 cm) min.

Secondary protection ONLY

Primary Monitored Entrapment

Secondary protection ONLY

Primary Monitored Entrapment

Secondary protection ONLY

Primary Monitored Entrapment

S R

6" (15 cm) max. above the

ﬂoor and away from the door

6" (15 cm) max. above the

ﬂoor and away from the door

6" (15 cm) max. above the

ﬂoor and away from the door

Wing

Nut

Mounting Bracket

Mounting

Bracket

6" (15 cm)

Max. above

the floor and away

from the door.

INSTALLATION

1. Attach the mounting brackets to a solid surface on each side of the door with hardware (provided) no more than 6" (15 cm) above the ﬂ oor.

Track mount is not recommended.NOTE:

2. Loosen the wing nut and slide the mounting bracket to adjust the photoelectric sensor.

SECONDARY PROTECTION AND ADJACENT DOOR INSTALLATIONS

Recommended installation for adjacent doors and more than one set of photoelectric sensors. NOTE: Secondary protection requires a CPS3 card.

Recommendations for optimizing operation of high volume vehicle trafﬁ c with two sets of monitored photoelectric sensors.

1 2 3 4 5 6 7 8 9 10 11 12

13 14 15 16 17 18 19 20 21 22 23 24

WIRING

Do not run wiring in the same conduit with AC power.

1. Disconnect power to the operator.

2. Run wire from both photoelectric sensors to the operator.

3. Connect wires from the photoelectric sensors as illustrated below for your operator type. The wiring is polarity sensitive so make certain to wire as