Liftmaster 880LMW Handleiding

Liftmaster Niet gecategoriseerd 880LMW

Lees hieronder de 📖 handleiding in het Nederlandse voor Liftmaster 880LMW (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
1
Smart Control Panel®
Safety Reversing Sensors
SMART CONTROL PANEL®
Model 880LMW
To prevent possible SERIOUS INJURY or DEATH from
electrocution:
• Be sure power is NOT connected BEFORE installing door
control.
• Connect ONLY to 12 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a closing
garage door:
• Install door control within sight of garage door, out of reach
of children at a minimum height of 5 feet (1.5 m), and away
from ALL moving parts of door.
• NEVER permit children to operate or play with door control
push buttons or remote control transmitters.
• Activate door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep garage door in sight until completely closed.
NEVER permit anyone to cross path of closing garage door.
FEATURE OVERVIEW
The features are adjustable and may be turned off or on as desired. Refer to the Feature Settings section.
A
A
SCREEN
The screen will display the time and temperature until the menu
button is pressed, and then it will display the menu options. If
there is a problem with the garage door opener the screen will
display the Diagnostic Code.
LIGHT BUTTON
Press the LIGHT button to turn the garage door opener lights on or
off. When the lights are turned on they will stay on until the LIGHT
button is pressed again, or until the garage door opener is
activated. Once the garage door opener is activated the lights will
turn off after the specified period of time (the factory setting is
4-1/2 minutes). The LIGHT button will not control the lights when
the door is in motion. The duration of the light timing can be
adjusted by accessing the menu using the navigation buttons.
MOTION SENSOR
The motion sensor will automatically turn on the garage door
opener lights when motion is detected. The lights will come on for
the set period of time, then shut off. The factory setting is on and
set at 4-1/2 minutes.
LOCK
The LOCK feature is designed to prevent activation of the garage
door opener from remote controls while still allowing activation
from the door control and keyless entry. This feature is useful for
added peace of mind when the home is empty (i.e. vacation).
TIMER-TO-CLOSE (TTC)
DO NOT enable TTC if operating a one-piece door. TTC is to be
used ONLY with sectional doors. Factory default is set to off. TTC
can be set to automatically close your garage door from the fully
open position after a specified period of time (1, 5, 10 minute
intervals or a custom setting up to 99 minutes). The garage door
opener will beep and the lights will flash before closing the door.
The screen on the door control can display the status of the TTC.
TTC WILL NOT work if the garage door opener is operating by
battery power or if the safety reversing sensors are misaligned.
This feature is NOT intended to be the primary method of closing
the door. A keyless entry should be installed in the event of an
accidental lock out when using this feature.
MAINTENANCE ALERT SYSTEM (MAS)
This feature assists the homeowner in ensuring the garage door
opener system stays in good working condition. A maintenance
alert message will display on the screen indicating the garage door
opener may be in need of maintenance.
The MAS feature MUST be activated at time of installation. The
factory setting is off.
WARNING: This product can expose you to chemicals including
lead, which are known to the State of California to cause cancer or
birth defects or other reproductive harm. For more information go
to www.P65Warnings.ca.gov.
2
Install the door control within sight of the door at a minimum
height of 5 feet (1.5 m) where small children cannot reach, and
away from the moving parts of the door. For gang box installations
it is not necessary to drill holes or install the drywall anchors. Use
the existing holes in the gang box.
NOTE: Pre-wiring means that your garage already has wires
installed for the door control.
1 Unplug the garage door opener to prevent the garage door
opener from activating during wiring.
2 Strip 7/16 inch (11 mm) of insulation from one end of the wire
and separate the wires.
3 Connect one wire to each of the two screws on the back of the
door control. The wires can be connected to either screw.
PRE-WIRED INSTALLATIONS: Choose any two wires to
connect, but make note of which wires are used.
1 Mark the location of the bottom mounting hole and drill a 5/32
inch (4 mm) hole.
2 Install the bottom screw, allowing 1/8 inch (3 mm) to protrude
from the wall.
3 Position the bottom hole of the door control over the screw and
slide down into place.
4 Lift the push bar up and mark the top hole.
5 Remove the door control from the wall and drill a 5/32 inch
(4 mm) hole for the top screw.
6 Position the bottom hole of the door control over the screw and
slide down into place. Attach the top screw.
7 Close the push bar.
1 Strip 7/16 inch (11 mm) of insulation from the end of the wire
near the garage door opener.
2 Connect the wire to the red and white terminals on the garage
door opener. The wires can be connected to either terminal. To
insert or release wire, push in tab with screwdriver tip.
3 Reconnect power to the garage door opener. If the door control
has been installed and wired correctly, a message will display
on the screen. To synchronize the garage door opener and the
door control, press the push bar up to 3 times, until the garage
door opener activates. The time and temperature will display on
the door control when the door control and the garage door
opener are synchronized.
PRE-WIRED INSTALLATIONS: Connect the same wires to the
garage door opener that were previously connected to the door
control.
GANG BOX
DRYWALL
RED
WHITE
GREY
Drywall Anchors
HARDWARE
2
1
7/16" (11 mm)
7/16" (11 mm)
2
1
3
B
INSTALLATION
BWIRE THE DOOR CONTROL CMOUNT THE DOOR CONTROL DWIRE TO GARAGE DOOR OPENER
C D
6ABx1-1/4" 6-32x1"
1
2
3
4
5
6
7
3
LOCK
When the Lock feature is on, your
remote controls have been
disabled and the following
message will display on the door
control:
BATTERY BACKUP ONLY
If your garage door opener has
a battery backup the following
message will display on the door
control if there is a problem with
the battery:
MAINTENANCE ALERT (MAS)
When the maintenance alert is
on and the garage door opener
needs maintenance the following
message will display on the
screen:
PUSH BAR
Press the push bar to open or close the door.
NAVIGATION BUTTONS
Use the navigation buttons to make selections and program
features.
GARAGE DOOR OPENER LIGHTS
Press the LIGHT button to turn the garage door opener lights on
or off. When the lights are turned on they will stay on until the
LIGHT button is pressed again, or until the garage door opener is
activated. Once the garage door opener is activated the lights will
turn off after the specified period of time (the factory setting is
4-1/2 minutes). The LIGHT button will not control the lights when
the door is in motion.
MOTION SENSOR
This feature will automatically turn on the garage door opener
lights when motion is sensed. The lights will come on for the set
period of time, then shut off.
LIGHT FEATURE
The lights will turn on when someone enters through the open
garage door and the safety reversing sensor infrared beam is
broken.
If using the garage door opener light as a work light, turn the light
on using the light button on the wall control or the light will turn
off if you are beyond the range of the sensor.
Push Bar
LIGHT Button
Screen
Motion Sensor
Navigation Buttons
TIMER-TO-CLOSE (TTC)
DO NOT enable TTC if operating a one-piece door. TTC is to be
used ONLY with sectional doors.
Once the TTC has been set and the door is open, the selected
close interval will be displayed on the screen and toggle between
the time and TTC message. The garage
door opener will beep and the lights will
flash before closing the door.
When the TTC is on the following
message will display on the door control:
To temporarily suspend the TTC feature
press and release the HOLD button.
Press REL button to resume normal TTC
operation.
The TTC feature will deactivate if the garage door encounters two
sequential obstructions; or the safety reversing sensors are
incorrectly installed. The garage door will reverse open and WILL
NOT close until the obstructions are removed or the safety
reversing sensors are correctly installed.
When the obstruction has been cleared
or the safety reversing sensors have
been aligned, the door will close when
the garage door opener is activated.
ALERT
E
OPERATION
E

Product specificaties

Merk: Liftmaster
Categorie: Niet gecategoriseerd
Model: 880LMW

Heb je hulp nodig?

Als je hulp nodig hebt met Liftmaster 880LMW stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Liftmaster

Liftmaster

Liftmaster CAPXLV2MC Handleiding

5 Augustus 2024
Liftmaster

Liftmaster BG770 Handleiding

8 Juli 2024
Liftmaster

Liftmaster LMHNTG Handleiding

8 Juli 2024
Liftmaster

Liftmaster SL585 Handleiding

11 Juni 2024
Liftmaster

Liftmaster SL590 Handleiding

11 Juni 2024
Liftmaster

Liftmaster BG3000 Handleiding

11 Juni 2024
Liftmaster

Liftmaster CAPXSTKPL Handleiding

9 Juni 2024
Liftmaster

Liftmaster BG790 Handleiding

9 Juni 2024
Liftmaster

Liftmaster 64LM Handleiding

27 Mei 2024
Liftmaster

Liftmaster CAPXSHOOD Handleiding

8 December 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Protector

Protector AS-5030.3 V2 Handleiding

21 December 2024
Sabrent

Sabrent AU-MMCW Handleiding

21 December 2024
Sabrent

Sabrent AU-2X35 Handleiding

21 December 2024
Sabrent

Sabrent CB-RS232 Handleiding

21 December 2024
Owon

Owon 500W Handleiding

21 December 2024
Owon

Owon 300W Handleiding

21 December 2024
Sabrent

Sabrent SB-RKTQ4-1TB Handleiding

21 December 2024
Sabrent

Sabrent SB-RKTQ-1TB Handleiding

21 December 2024
Sabrent

Sabrent SB-ROCKET-1TB Handleiding

21 December 2024
Sabrent

Sabrent SB-HTSS Handleiding

21 December 2024