Liftmaster 041DJ003MC Handleiding

Liftmaster Niet gecategoriseerd 041DJ003MC

Lees hieronder de 📖 handleiding in het Nederlandse voor Liftmaster 041DJ003MC (24 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 174 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/24

Logic Board

Model 041DJ003MC

Also replaces 050DCRJWF

WARNING: This product can expose you to chemicals

including lead, which are known to the State of California to

cause cancer or birth defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov.

To prevent possible SERIOUS INJURY or DEATH:

• Disconnect ALL electric and battery power BEFORE performing ANY

service or maintenance.

To prevent damage to the receiver/logic board, DO NOT touch printed

circuit board of replacement receiver/logic board during installation.

ALWAYS wear protective gloves and eye protection when changing the

battery or working around the battery compartment.

NOTICE: This device complies with Part 15 of the FCC rules and Industry

Canada’s license-exempt RSSs. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2)

this device must accept any interference received, including interference

that may cause undesired operation.

Any changes or modiﬁ cations not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

This device must be installed to ensure a minimum 20 cm (8 in.) distance

is maintained between users/bystanders and device.

This device has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC rules and Industry

Canada ICES standard. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment o and on,

the user is encouraged to try to correct the interference by one or more of

the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that

to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Before you begin. Your new myQ® serial number is located on the

replacement label with your replacement logic board. You will need this new myQ

serial number to connect your opener to the network.

Disconnect power.1. 2. Open the front panel . (A)

Remove the battery cover. 3.

Disconnect the battery. Remove

the battery and set aside .(B)

Disconnect the wires coming 4.

from the safety reversing sensors,

door control, door lock and cable

tension monitor from the logic

board .(C)

Remove the logic board cover .5. (D)

Disconnect all the wiring harnesses 6.

from the logic board .(E)

Remove the four screws securing 7.

the logic board, remove the logic

board , and discard.(F)

Install the new logic board and 8.

connect the wiring harnesses. Route

the antenna through the channel in

the new battery cover.

Adhere the new myQ serial number 9.

label over the original label on the

logic board cover.

10. Set door proﬁle for new replacement

logic board. See page 2 to set door

proﬁle steps.

11. Reprogram the travel and test the

safety reversal system (see pages 2

and 3).

12. Program all remote controls and

keyless entries (see page 4).

13. Use the myQ app to add the new

myQ serial number to your account.

Red wire (+)

Battery Status LED

Black wire (-)

Antenna

NOTE: Be sure the short antenna is not pinched by the battery door and held in place

as shown.

NOTE: Please read these instructions as programming may be different from older

programming.

To prevent possible SERIOUS INJURY or DEATH, follow instructions to

select and set door proﬁle for safe and proper operation.

4-6 inch

diameter

8 inch

diameter

8 inch

diameter

To prevent possible SERIOUS INJURY or DEATH, after ANY changes to

the door proﬁle, reprogram limits.

Adjustment

Identify Door Proﬁle

To identify the door proﬁle number, measure the full drum diameter based

on the images below.

NOTE: This step is important to ensure the proper operation of the unit.

To view a video demonstration of how to identify and set the door proﬁle,

scan the QR code.

Standard Lift Sectional Door

• Door Proﬁle 1 = Standard to Heavy Weight Door* with a 4” drum

(Recommended).

• Door Proﬁle 2 = Light Weight Door with a 4” drum.

• Door Proﬁle 3 = Heavy Weight Door* with a 6” drum.

• Door Proﬁle 4 = Light Weight Door with a 6” drum.

*NOTE: Drum sizes may vary by manufacturer.

For Standard Lift Sectional Doors:

•Drums less than or equal to 5”, use 4” drum.

•Drums more than 5”, use 6” drum.

Standard to Heavy Weight doors are those with solid wood interiors, wood

veneer exteriors, glass windows, insulation, and/or decorations.

High Lift Door

• Door Proﬁle 5 = Tapered drum with tracks that raise to a higher elevation

Vertical Lift Sectional Door

• Door Proﬁle 5 = Tapered Drum with tracks raising vertically above the

opening.

Set Door Proﬁle

1. To enter Set Door Proﬁle mode, press and hold the black button for

one second. The UP and DOWN buttons turn a solid color.

2. To set Door Proﬁle, press the UP and DOWN buttons. The Learn LED

button blinks and beeps as you change the setting.

3. The number of Learn LED button blinks indicates which proﬁle you

have selected. There is no preset door proﬁle setting.

4. Press and release the Black button to set the Door Proﬁle. This process

is now complete. Proceed to the Travel Learn mode.

EXITING DOOR PROFILE NUMBER SETTING

If there is no selection within 4.5 minutes, the Door Proﬁle selection mode

will be cancelled with a long beep.

Adjustment

Program the Travel

Travel limits regulate the points at which the door will stop when moving

up or down.

While programming the travel, the UP and DOWN buttons can be used to

move the door as needed. During the Automatic Force Setup, the door will

automatically open and close.

1. Press and hold the Adjustment Button until the UP Button begins to

flash and/or a beep is heard. The Safety Reversing Sensors will be

disconnected during the Program the Travel process.

2. Press and hold the UP Button until the door is in the desired UP

position.

3. Once the door is in the desired UP position press and release the

Adjustment Button. The garage door opener lights will flash twice and

the DOWN Button will begin to flash.

4. Press and hold the DOWN Button until the door is in the desired

DOWN position.

5. Once the door is in the desired DOWN position press and release the

Adjustment Button. The garage door opener lights will flash twice.

Program the Travel is now complete. If the garage door opener lights

flash 5 times, then programming has timed out and the Travel Limits

have not been set. Please restart the Program the Travel process.

Without a properly installed safety reversal system, persons

(particularly small children) could be SERIOUSLY INJURED or KILLED

by a closing garage door.

• Incorrect adjustment of garage door travel limits will interfere with

proper operation of safety reversal system.

• After ANY adjustments are made, the safety reversal system MUST

be tested. Door MUST reverse on contact with 1-1/2" high (3.8 cm)

object (or 2x4 laid flat) on floor.

To prevent damage to vehicles, be sure fully open door provides

adequate clearance.

Button

Adjustment

Button

DOWN

Button

Programming Buttons

To prevent possible SERIOUS INJURY or DEATH, after ANY changes to

the door proﬁle, reprogram limits.

Automatic Force Set Up

Once both the up and down positions have been manually set, the Safety

Reversing Sensors will reconnect and become operational. Then, the opener

will enter a force-sensing operation by automatically moving the door open

and close. The garage door opener will sound an audible and visual alert

before automatically opening and closing the door. The garage door opener

will beep three times, confirming that the Automatic Force Setup completed

successfully. Adjustment is complete.

If you hear one long beep after the door attempts to move, then the

Automatic Force Set Up has not completed successfully. Please start over at

step 1 of Program the Travel.

Product specificaties

Merk:	Liftmaster
Categorie:	Niet gecategoriseerd
Model:	041DJ003MC

Heb je hulp nodig?

Als je hulp nodig hebt met Liftmaster 041DJ003MC stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Liftmaster

Liftmaster CAPXLV2MC Handleiding

5 Augustus 2024

Liftmaster BG770 Handleiding

8 Juli 2024

Liftmaster LMHNTG Handleiding

8 Juli 2024

Liftmaster SL585 Handleiding

11 Juni 2024

Liftmaster SL590 Handleiding

11 Juni 2024

Liftmaster BG3000 Handleiding

11 Juni 2024

Liftmaster CAPXSTKPL Handleiding

9 Juni 2024

Liftmaster BG790 Handleiding

9 Juni 2024

Liftmaster 64LM Handleiding

27 Mei 2024

Liftmaster CAPXSHOOD Handleiding

8 December 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Protector AS-5030.3 V2 Handleiding

21 December 2024

Sabrent AU-MMCW Handleiding

21 December 2024

Sabrent AU-2X35 Handleiding

21 December 2024

Sabrent CB-RS232 Handleiding

21 December 2024

Owon 500W Handleiding

21 December 2024

Owon 300W Handleiding

21 December 2024

Sabrent SB-RKTQ4-1TB Handleiding

21 December 2024

Sabrent SB-RKTQ-1TB Handleiding

21 December 2024

Sabrent SB-ROCKET-1TB Handleiding

21 December 2024

Sabrent SB-HTSS Handleiding

21 December 2024