Levenhuk Wezzer Plus LP30 Handleiding

Levenhuk Weerstation Wezzer Plus LP30

Lees hieronder de 📖 handleiding in het Nederlandse voor Levenhuk Wezzer Plus LP30 (47 pagina's) in de categorie Weerstation. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/47
Levenhuk Inc. (USA): 928 E 124th Ave. Ste D, Tampa, FL 33612, USA,
+1-813-468-3001, contact_us@levenhuk.com
Levenhuk Optics s.r.o. (Europe): V Chotejně 700/7, 102 00 Prague 102,
Czech Republic, +420 737-004-919, sales-info@levenhuk.cz
LevenhukÂŽ is a registered trademark of Levenhuk, Inc.
© 2006—2022 Levenhuk, Inc. All rights reserved.
www.levenhuk.com
Levenhuk
Wezzer PLUS LP30
Thermometer
2
Levenhuk Wezzer PLUS LP30 Thermometer
The kit includes: base station, sensor, user manual, and warranty.
Also required (not included):
2 AAA batteries for the sensor
3 AAA batteries for the base station
Parts overview
Base station
1. SET button
2. UP button
3. DOWN button
4. MEM button
5. CH button
6. Battery compartment cover
7. Table stand (fold-out)
Sensor
1. Temperature
2. Humidity
3. Current channel
4. LED indicator
5. Wall mount hole
6. RESET button
7. Channel switch (1—3)
8. Battery compartment cover
9. Battery compartment
Interface icons
1. Time display
2. Low battery indicator
3. Calendar and week display
4. Sensor connection status
5. Outdoor temperature
6. Indoor temperature
7. Outdoor temperature trend
8. Indoor temperature trend
9. MAX./MIN. temperature record
10. Atmospheric pressure trend
11. Weather forecast
EN
CH MEM DOWN UP SET
5 1
2
4
3
6
7
CH1
3
1
2
1 2 3
+
-AAA 1.5V
7
4
+
-AAA 1.5V
5
6
8
9
12 00:
18 20
T H U
6/27
FUTURE FORECAST
OUTDOOR
° °C C
INDOOR
TREND
TREND TREND
MAX
MIN
1
2
11
10
9
8
67
3
4
5
LOW
LOW
3
Getting started
Base station
• Open the battery compartment cover (6) and insert 3 batteries according to the correct
polarity. Close the cover.
• Wait until the indoor temperature is displayed on the base station.
Sensor
• Open the battery compartment cover (8). The sensor should be operated on channel 1.
• Insert 2 batteries according to the correct polarity. Close the cover.
• To re-establish the sensor connection manually, press using a pin.RESET
Sensor connection
• Place the base station and the remote sensor within the eective transmission range. Ensure
that the channels are assigned after you set up the power supply for the base station and all
the sensors.
• If the reception is successful, the display will show the temperature of the respective
outdoor sensor. If the values are not received from a channel, "—" appears on the display.
Check the batteries and try it again. Check if there is any source of interference.
• When changing batteries, replace the batteries rst in the base unit, and then in all the
sensors, to re-establish the connection. If an adapter supplies power to any of the devices,
briey disconnect the power to that device when replacing the batteries. If you change
the batteries only in one of the devices (for example, in the sensor), the signal may not be
received correctly.
• If you have problems in receiving the readings, make sure that channel 1 is selected on the
sensor, and then press and hold on the base station for 5 seconds.CH
• The eective range may dier depending on the unit’s position. Due to interference (various
remote control devices, etc.), the maximum distance between the base unit and the sensor
may be signicantly reduced. In such cases, we suggest moving the base unit and sensor a
little. Sometimes it is enough to move one of these units a few inches!
NOTE! Although the sensor is weather resistant, never place it in direct sunlight or
in the rain or snow.
Time setting
Press the button and hold it for 3 seconds. The digits that are to be set are ashing. Press SET UP
or to continue.DOWN SET to change the value, and then press
The setting order: Hours > Minutes > Year > Month > Date > Temperature unit.
Finally, press the button to save the settings and exit.SET
The language and the selected abbreviations for each day of the week are shown in the following
table.
Weather
Temperature
Press the button to switch between °C and °F. UP
Weather forecast
Language Monday Tuesday Wednesday Thursday Friday Saturday Sunday
English, EN MON TUE WED THU FRI SUNSAT
1 2 3 4 5
1. Sunny
2. Partly cloudy
3. Cloudy
4. Rainy
5. Snowy


Product specificaties

Merk: Levenhuk
Categorie: Weerstation
Model: Wezzer Plus LP30

Heb je hulp nodig?

Als je hulp nodig hebt met Levenhuk Wezzer Plus LP30 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Weerstation Levenhuk

Handleiding Weerstation

Nieuwste handleidingen voor Weerstation