Lanzar VIBE 276 Handleiding

Lanzar Autoradio VIBE 276

Lees hieronder de šŸ“– handleiding in het Nederlandse voor Lanzar VIBE 276 (9 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 55 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/9
V i b e r a n t O w n e r ā€™ s M a n u a l - 1
123765
Congratulations on your purchase of a Lanzar Viberant amplifier. You have purchased a quality product designed
and engineered to give you many years of uncompromised musical service. VIBE ampliļ¬ers are designed with
the latest technology available, which provides headroom for even the most demanding peaks and dynamic ranges
found on modern CD's and recordings.
T A B L E O F C O N T E N T S
System Wiring
6. 2 channel stereo
7. 2 channel bridged mode
8. 2 channel tri-mode
9. 2 channel triamp system
10. 4 channel stereo
11. 4 channel bridged mode
12. 4 channel tri-mode
13. Precautions
14.Troubleshooting
15.Notes
1. INPUT LEVEL CONTROLS
Enables the matching of input levels to the output levels from
head unit (or other signal source).
2. CROSSOVER MODE SELECTOR
Determines the mode of built-in crossover:
low pass (permits only low frequency signals to pass to speakers),
high pass (permits only high frequency signals to pass to speakers),
or ļ¬‚at.
3. BASS BOOST CONTROL
With a bass boost switch engaged, the bass level is increased
approx 18dB.
4. REMOTE BASS BOOST
Plug in the remote bass boost control wire in here
5. POWER & PROTECTION INDICATORS
Provide instant information on status of ampliļ¬er, including
short-circuit and thermal overload alerts.
6. HIGH PASS FILTER (HPF)
When Crossover Mode Selector is in High Pass Mode, this control
limits the frequencies which will be distributed to the speakers
to those below the value to which this is set within the range 80-
2.5KHz.
7. LOW PASS FILTER (LPF)
When Crossover Mode Selector is in Low Pass Mode, this control
limits the frequencies which will be distributed to the speakers
to those below the value to which this is set within the range 35-
400Hz.
Table of Contents
Feature and Controls
1. VIBE 226/236/246/256/266/276/286
2. VIBE 416/426/436
3. Installation
4. Speciļ¬cations
Feat u r e s a n d C o n tro l
s
V i b e r a n t O w n e r ā€™ s M a n u a l
VIBE 226/236/246/256/266/276/28
6
4
V i b e r a n t O w n e r ā€™ s M a n u a l - 3
1. REMOTE BASS BOOST
Plug in the remote bass boost control wire in here
2. INPUT LEVEL CONTROLS
Enables the matching of input levels to the output levels from
head unit (or other signal source).
3. CROSSOVER MODE SELECTOR
Determines the mode of built-in crossover:
low pass (permits only low frequency signals to pass to speakers),
high pass (permits only high frequency signals to pass to speakers),
or ļ¬‚at.
4. BASS BOOST CONTROL
With a bass boost switch engaged, the bass level is increased
approx 18dB.
5. POWER & PROTECTION INDICATORS
Provide instant information on status of ampliļ¬er, including
short-circuit and thermal overload alerts.
6. HIGH PASS FILTER (HPF)
When Crossover Mode Selector is in High Pass Mode, this control
limits the frequencies which will be distributed to the speakers
to those below the value to which this is set within the range 80-
2.5KHz.
7. LOW PASS FILTER (LPF)
When Crossover Mode Selector is in Low Pass Mode, this control
limits the frequencies which will be distributed to the speakers
to those below the value to which this is set within the range 35-
400 Hz.
1. Find a suitable location in the vehicle to mount the ampliļ¬er.
2. Make sure there is suļ¬€icient air ļ¬‚ow around the intended mounting location.
3. Bolt the ampliļ¬er to the mounting surface.
4. Connect the power ground terminal to the nearest point on the chassis of the car. Keep this ground wire less than one meter (39")
in length. Use 8 gauge wire.
5. Connect the remote terminal to the remote output of the head unit using 14 gauge wire.
6. Connect an empty fuse holder within 300mm (12") of the battery and run 8 gauge of larger high quality cable from this fuse to the
ampliļ¬er location.
7. Make sure there is no fuse in this fuse holder. Then make the connection to the "BATT" connection on the ampliļ¬er.
8. If multiple ampliļ¬ers are being used, use cables (each with its own fuse at the battery) or a #0 or #2 cable from the fuse holder at
the battery to a distribution block at or near the ampliļ¬er's location.
9. Connect all line inputs and outputs using high-quality RCA-RCA cables.
10. Insert fuse(s) at the battery fuse holder(s).
11. Recheck all connections before powering up.
12. Set all level controls to their least sensitive positions and set all crossover controls, switches, etc. to the desired frequency or
position.
13. Once the system is powered up, set the volume control on the head unit to about the 2 o'clock position, and then set all the
ampliļ¬ers' level controls for maximum output level.
14. Further ļ¬ne tuning of the various controls may be necessary to obtain the desired results.
V i b e r a n t O w n e r ā€™ s M a n u a l2 -
Feat u r e s a n d C o n tr o l s I n s ta ll ati o
n
VIBE 416/426/436
5 234762 3 476
1


Product specificaties

Merk: Lanzar
Categorie: Autoradio
Model: VIBE 276

Heb je hulp nodig?

Als je hulp nodig hebt met Lanzar VIBE 276 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Autoradio Lanzar

Handleiding Autoradio

Nieuwste handleidingen voor Autoradio