Lanzar HTG237 Handleiding

Lanzar Receiver HTG237

Lees hieronder de 📖 handleiding in het Nederlandse voor Lanzar HTG237 (23 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 81 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/23

< 3 >

Owners Manual before beginning installation.

WARNING

High powered audio systems in a vehicle are capable of generating "Live Concert"

high levels of sound pressure. Continued exposure to excessively high volume

sound levels may cause hearing loss or damage. Also, operation of a motor vehicle

while listening to audio equipment at high volume levels may impair your ability to

hear external sounds such as; horns, warning signals, or emergency vehicles, thus

contributing to a potential trafﬁc hazard. In the interest of safety, HERTIAGE

recommends listening at lower volume levels while driving.

< 4 >

TROUBLE SHOOTING GUIDE .............................................................

SPECIFICATION .......................................................................................

WARNING .................................................................................................

PLANNING YOUR SYSTEM

Before beginning the installation, consider the following:

1. Do you plan to add additional mobile electronics equipment in the future?

If you plan to expand your system by adding other components sometime in the

future, ensure adequate space is left and cooling requirements are met.

2. Should you use high or low level inputs?

Your Ampliﬁer has been designed to accept Low-Level(Pre-Amp outputs from your

radio) source signal. If your radio/source is equipped with Pre-Amp outputs, it is

possible to utilize them to drive the Ampliﬁer and the 2 front speakers. Then, use the

built-in power of your radio to drive the 2 rear speakers.

3. Are your components matched?

The RMS power rating of your speaker(s) must be equal or greater than the RMS

power rating of your ampliﬁer. Your speaker(s) also must be 2 - 8 Ohms impedance

for stable ampliﬁer operation. Impedance information is normally printed on the

speaker basket or magnet.

4. Where will the ampliﬁer be installed?

Consider both the length of your leads, and routing when determining the mounting

location. It is best to run power and RCA wiring on opposite sides of the vehicle to

prevent induced noise. Pre-amp input jacks require a length of high quality shielded

male to male RCA patch cord.

Product specificaties

Merk:	Lanzar
Categorie:	Receiver
Model:	HTG237
Kleur van het product:	Zwart
Breedte:	223.8 mm
Diepte:	249.9 mm
Hoogte:	56.9 mm
LED-indicatoren:	Power, Temperature
Aan/uitschakelaar:	Ja
Connectiviteitstechnologie:	Bedraad
DC voltage input:	12 V
Bedoeld voor:	Auto
Audio (L,R) out:	3
Audio-uitgangskanalen:	2.0 kanalen
Frequentiebereik:	10 - 45000 Hz
Signaal/ruis-verhouding:	90 dB
Totale harmonische vervorming (THD):	0.01 procent
Regeling van bass-niveau:	Ja
Piekvermogen per kanaal:	1000 W
Speakers connectiviteit type:	Banaanstekker/poolklem
RMS vermogen uitvoer per kanaal (4 Ohm):	125 W
Line inputs (RCA):	1
High pass filter:	Ja
Low pass filter:	Ja
Gain aanpassing:	Draaiknop
RMS vermogen uitvoer per kanaal (2 Ohm):	225 W
Bass boost:	0 - 12 dB
Ingebouwde crossover:	Ja
High-pass filterbereik:	80 Hz
Low-pass filterbereik:	50 - 250 Hz
Waarde zekering:	25A
Maximaal uitgangsvermogen:	1000 W
Aarding:	Ja