Kramer T10F-22M Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Kramer T10F-22M (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
The T10F 22MKramer - Inner Frame
Congratulations on purchasing your Kramer Inner Frame for the T10F 22M- TBUS-10XL Table
Connection bus.
The includesT10F 22M- Inner Frame :
• An opening for 1 - SID X1 or other MegaTOOL
• 2 s power socket opening
• 1 blank insert
• 1 pass through
insert
Note that you can install the optional T-2INSERT (P/N: 80-00006699) inside
a single power socket opening.
Figure 22M1 -: T10F - ) Inner Frame (P/N: 80 000028
Installing the Wall Plate Inserts
Before installing the inner frame, you need to wall plate insertsinstall .
Go to to check for uphttp://www.kramerelectronics.com - -to date user
manuals and the omplete list of Kramer wall plate and module c inserts
connectors.
You can rearrange or remove any of the blank inserts mounted on the inner frame and replace
them with Kramer wall or connector modules for interfacing A/V type signals. plate inserts
To mount a Kramer insert or connector module:
1. Unscrew the two screws that fasten the blank insert to the inner frame and remove the
blank insert.
2. Place the required Kramer wall plate insert over the opening, insert the two screws to fix
the Kramer insert in place, and tighten them.
Installing the -SID X1 or other MegaTOOL
To install , as shown inthe SID-X1 Figure 2:
1. Fasten each of the supplied TOOL brackets to their location (one on each side).
2. Insert the SID-X1, from underneath, through the MegaTOOL opening.
3. . Fasten the screws (one on each side) through the inner frame holes and TOOL brackets
Figure 2 : Installing the SID-X1
Installing the Inner Frame
To install the inner frame:T10F 22M-
1. Place the assembled inner frame inside the TBUS-10XL enclosure.
2. Set the required height using your fingers to bring the inner frame to the desired position,
and then screw and tighten it in place using the height adjustment screws supplied with the
inner frame.
i
i
Connecting the Cables
When replacing blank inserts with connector inserts (for example, VGA, audio, HDMI and so on):
1. Insert the cables to their appropriate connectors from underneath.
2. . Secure the cables to the tie holes on the TBUS-10XL
Do not secure the cables too tightly or too loosely. Leave a small amount of slack.
After the is connected to mains power and the proper cables, it is ready for use.TBUS-10XL
Adjusting the Height of the Inner Frame
If needed, you can adjust the possible heights to accommodate inner frame to several one of the
large or bulky cables. To adjust, perform the following:
1. Remove the height adjustment screws, while supporting the frame from underneath with
your fingers.
2. Raise or lower the connecting surface to the required height, insert the screws, and tighten
them in place.
K R A M E R ELE C T R O N I C S LT D .
Installation
Instructions
MODEL:
T10F 22M-
Inner Frame
For the latest information on our products and a list of Kramer
distributors, visit our Web site where updates to this user manual may be
found.
We welcome your questions, comments, and feedback.
Web site: www.kramerelectronics.com
E-mail: info@kramerel.com
P/N: 2900-300 Rev 225 1
P/N:
2900- 300225
Rev:
1


Product specificaties

Merk: Kramer
Categorie: Niet gecategoriseerd
Model: T10F-22M

Heb je hulp nodig?

Als je hulp nodig hebt met Kramer T10F-22M stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Kramer

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd