Kramer KDS-8-MNGR Handleiding

Kramer AV extender KDS-8-MNGR

Lees hieronder de 📖 handleiding in het Nederlandse voor Kramer KDS-8-MNGR (4 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

KDS-8-MNGR Quick Start

P/N:

2 9 0 0 - 3 0 1 4 5 9 QS

Rev:

Scan for full manual

KDS-8-MNGR Quick Start Guide

This guide helps you install and use your KDS-8-MNGR for the first time.

Go to www.kramerav.com/downloads/KDS-8-MNGR to download the latest user manual and check if

rmware upgrades are available.

Step 1: Check in the b what’s ox

KDS-8-MNGR SDVoE Manager

1 Quick start guide

1 Power adapter and cord

1 Rubber foot square

Step 2: Get to know your -8-MNGR KDS

Feature

Function

POWER LED

This LED illuminates to indicate the unit is on and receiving power.

IR Window

For future use.

Feature

Function

IR EXT Port

For future use.

CONTROL 5-pin Terminal

Block Connector

For future u .se

RS-232 3-pin Terminal Block

Connector

Connect to a PC, laptop or other serial control device with a 3-pin adapter cable, to control

the unit via RS-232.

TRIGGER IN 10-pin Terminal

Block Connector

Connect any device with trigger switch functionality such as window security alarms, motion

detectors, door switches, etc.

Each of the 8 trigger inputs will activate the associated macro (1 to 8) when triggered.

HDMI OUT Port

Connect to a standard HDMI ™ display to view the unit’s current status information and

access the WebGUI directly without a PC.

HDMI output is locked to a resolution of 1080p@60Hz.

USB Port

Connect a USB mouse and keyboard to control the unit’s WebGUI displayed on the HDMI

output port. Firmware update via USB is also supported.

Specialized USB control devices, such as a touch panel, should be connected

before the unit is powered on.

LAN 2 Port

Connect directly, or through a network switch, to your PC/ laptop to control the unit via

WebGUI/Telnet.

# Feature Function

LAN 1(POE) Port

This port is used to connect to the SDVoE devices to be controlled. Connect to the SDVoE

units’ private network through their dedicated network switch, to enable detection and control

over those units.

If the connected network switch supports the IEEE 802.3af 2003 PoE (Power over

Ethernet) standard, this unit can optionally be powered directly via this Ethernet port.

RESET Button

Press and hold for 3 seconds to reset the unit to its factory defaults, including Ethernet

settings.

While the reset is in process, the LEDs on the front of the unit flash. Once the reset

is complete, the unit returns to normal operation.

DC 5V Port

Plug the 5V DC power adapter into the unit and connect it to an AC wall outlet for power.

(Optional, not required if the unit is powered via PoE).

Step 3: Mount -8-MNGR KDS

Install KDS-8-MNGR using one of the following methods:

• Attach the rubber foot pad and place the unit on a at surface.

• Fasten a bracket on each side of the unit to a at surface

(see www.kramerav.com/downloads/K -8-MNGRDS ).

• Ensure that the environment (e.g., maximum ambient temperature &

air ow) is compatible for the device.

• Avoid uneven mechanical loading.

• Appropriate consideration of equipment nameplate ratings should be

used for avoiding overloading of the circuits.

• Reliable earthing of rack-mounted equipment should be maintained.

Step 4: Connect inputs and outputs

Always switch OFF the power on each device before connecting it to your KDS-8-MNGR.

For optimal performance, use the recommended Kramer cables available at . www.kramerav.com/product/KDS-8-MNGR

Using third-party cables may cause damage!

Step 5: Connect power

Connect the power adapter and cord to KDS-8-MNGR and plug it into the mains electricity. If the connected network switch

supports the PoE, KDS-8-MNGR can optionally be powered directly via the LAN 1 (POE) port.

Safety Instructions (See for updated safety information)www.kramerav.com

Caution:

• For products with relay terminals and GPI\O ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.

• There are no operator serviceable parts inside the unit.

Warning:

• Use only the power cord that is supplied with the unit.

• Disconnect the power and unplug the unit from the wall before installing.

• Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.

• To ensure continuous risk protection, replace fuses only according to the rating specified on the product label which located on the bottom of the unit.

Step 6: Operate -8-MNGR KDS

Device Discovery

To discover a device:

1. Connect the unit and your PC/Laptop to the same active network via LAN 1 or LAN 2 port.

2. Connect to a standard HDMI ™ display to view the unit’s IP information in System Setting tab.

The current IP address can be veried using the HDMI output or RS-232.

Once the IP settings are known, you can use to connect to the device via Telnet or Web GUI. it

Web GUI Operation

After connecting to the Web GUI using device IP address in a web browser, the Web GUI loads displays the System tab. and

To use the Web GUI:

1. Click Login to the authentication window. open

2. Enter the appropriate user name and password.

The default user name / password is “admin / admin”.

3. Click to log in. Enter

If a keyboard is not available, (for example, when using a touch screen) an on-screen keyboard can be activated by

clicking on the keyboard icon ( ).

4. After logging in, use the menu tabs to operate the device.

In the System tab, click Logout to disconnect the currently connected user from the Web GUI, and return to the login page.

When not logged in, only the “Monitor & Control” and “System” tabs are available.

Product specificaties

Merk:	Kramer
Categorie:	AV extender
Model:	KDS-8-MNGR
Kleur van het product:	Zwart
Gewicht:	700 g
Breedte:	231 mm
Diepte:	108 mm
Hoogte:	25 mm
Gewicht verpakking:	1200 g
Breedte verpakking:	382 mm
Diepte verpakking:	188 mm
Hoogte verpakking:	60 mm
Soort:	AV-repeater
Gebruikershandleiding:	Ja
LED-indicatoren:	Stroom
Type verpakking:	Doos
Stroom:	4 A
USB-connectortype:	USB Type-A
Connectiviteitstechnologie:	Bedraad
Maximum resolutie:	1920 x 1080 Pixels
Type stroombron:	DC
Aantal USB-aansluitingen:	1
USB-versie:	2.0
Maximale refresh snelheid:	60 Hz
Materiaal:	Staal
Duurzaamheidscertificaten:	CE, Federal Communications Commission (FCC), RoHS, WEEE
Aantal per verpakking:	1 stuk(s)
Temperatuur bij opslag:	-20 - 60 °C
Naleving van duurzaamheid:	Ja
Power over Ethernet (PoE):	Ja
RS-232 ingangspoorten:	1
RS-232 uitgangspoorten:	1
Aantal HDMI-uitgangen:	1
RJ-45 invoer ports:	2
Operating voltage:	5 V
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	20 - 90 procent
Electrostatic Discharge (ESD) bescherming:	8 kV
Elektrostatische ontlading (ESD) bescherming:	Ja