Konig DL-DANCER250 Handleiding

Konig Effect machine DL-DANCER250

Lees hieronder de 📖 handleiding in het Nederlandse voor Konig DL-DANCER250 (69 pagina's) in de categorie Effect machine. Deze handleiding was nuttig voor 10 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/69

DL-DANCER250

MANUAL (p. 2)

Light xture Dancer 250W

MODE D’EMPLOI (p. 13)

Jeu de lumières Dancer 250W

MANUALE (p. 24)

Luminaria Dancer 250W

BRUKSANVISNING (s. 46)

Belysningsarmatur Dancer 250W

MANUAL DE UTILIZARE (p. 57)

Corp de iluminat Dancer 250W

HASZNÁLATI ÚTMUTATÓ (o. 35.)

250 W-os Dancer fényeffektus-vetítő

KÄYTTÖOHJE (s. 41)

Dancer 250W valolaite

GEBRUIKSAANWIJZING (p. 18)

Verlichtingsarmatuur Dancer 250W

ANLEITUNG (s. 7)

Lichteffekt Dancer 250W

MANUAL DE USO (p. 30)

Dispositivo luminoso Dancer 250W

NÁVOD K POUŽITÍ (s. 51)

Světelná konstrukce Dancer 250W

ΕΓΧΕΙΡΙΔΙΟ XPHΣHΣ (σελ. 62)

Συσκευή φωτισμού Χορευτής 250W

ENGLISH

INTRODUCTION:

This advanced, DMX controllable multi-color light effect has 14 different rotating gobo patterns. The

250W halogen lamp ensures a room lling effect. This light effect is ideal for permanent installation or

mobile use.

IMPORTANT INFORMATION BEFORE USE:

The DANCER250 is not for household use. It is not a toy: it presents risks of serious injury due to

electric shock, high heat, and intense light. For safe operation, read this manual before using the

xture and observe all warnings and precautions printed here and on the xture. If you have questions

about how to operate the xture safely, please contact your König distributor or dealer.

Precautions:

• For protection against dangerous electric shock, the xture must be grounded (earthed). The AC

mains supply shall be tted with a fuse or circuit breaker and ground-fault protection.

• The xture operating voltage is printed on the rating label. Verify that the operating voltage closely

matches the AC supply voltage before connecting the xture. Do not connect the xture if the

voltage on the label differs from the AC mains voltage by more than ve percent.

• Verify that all used power cables are undamaged and rated for the current requirements of all

connected devices before use.

• There are no user serviceable parts inside except the lamp. Refer for all service to a qualied

technician.

• Replace the lamp if it becomes defective or worn out. Allow the xture to cool for 15 minutes before

installing a new lamp and make sure the xture is disconnected from the AC mains supply.

• Keep all combustible materials (for example fabric, wood, paper) at least 50cm (20 inches) away

from the xture. Keep ammable materials well away from the xture.

• Provide a minimum clearance of 10cm (4 inches) around the fan and air vents.

• When suspending the xture above ground level, verify that the structure can hold at least

10 times the weight of all installed devices and secure the xture with an approved safety cable.

Block access below the work area whenever installing or removing the xture.

• When carrying the xture, lock the mounting bracket securely and do not touch the lens or mirrors.

• Do not expose the xture to rain or moisture.

• Do not illuminate surfaces within 1 meter (39 inches) of the xture.

• Do not operate the xture if the ambient temperature exceeds 40°C (104°F).

• Never place lters or other objects over the lens or mirrors.

Important! Electric dimmers may damage the electronic components.

Although the DANCER250 cannot be dimmed, it may be switched on and off remotely using switch

packs or the full-on and full-off levels on dimmer packs.

INSTALLATION:

The best way to hang the DANCER250 is to use a rigging clamp. Bolt the clamp securely to the

mounting bracket. Verify that the structure can hold at least 10 times the weight of all installed devices

and secure the xture with an approved safety cable. Change to the desired angle by adjusting the

mounting bracket and tighten both swivel locks.

Install the xture at least 50cm (20 inches) away from combustible materials. Keep ammable

materials well away from the xture. Make sure the xture does not illuminate surfaces within 1 meter

(39 inches).

To ensure maximum lamp life, provide a minimum clearance of 10cm (4 inches) around the fan and air

vents. Make sure the ambient temperature will not exceed 40°C (104°F) and do not place the xture

on or nearby a loudspeaker.

OPERATION:

Read “IMPORTANT INFORMATION BEFORE USE” rst and verify all precautions are fullled before

operating.

Make sure the correct lamp is installed, read “SERVICE” on how to (re)place the lamp.

Although the DANCER250 cannot be dimmed, it may be switched on and off remotely using switch

packs or the full-on and full-off levels on dimmer packs. Disconnect the xture from AC power when

not in use.

The DANCER250 has an advanced control panel. To set the desired function please read the following

instructions carefully.

Power

DMX

Up Down

Enter

Sound

Control panel

DMX address setting:

1. Press Menu to access address code setting menu

Axxxx

2. Press UP or DOWN to set the DMX address code.

3. Press ENTER to save the update DMX address code.

Address code setting range

A001-A512

Motor Speed and Sound Sensitivity setting:

1. Press Menu to access the menu StuP

2. Press ENTER to save the setting.

3. LCD display Mot1, press ENTER to access.

4. Press UP or DOWN to select motor speed, the range is 0-99.

5. Press ENTER to save the setting. Press

Menu to exit.

6. In Mot1 interface, press UP or DOWN to select

Mot2 and SEnS, the same setting as

SenS is

sound sensitivity; 0 is closed, 99 max sound sensitivity.

StuP → Mot1 0-99 Gobo motor speed

→ Mot2 0-99 Gobo rotate motor speed

→ SenS 0-99 Sound sensitivity

Test program:

Press Menu to access the test program, select

TESt and press ENTER to save the setting, the LCD

display ashes.

Press Menu to exit this scene.

Mode setting:

Press Menu to access the menu

ModE and press ENTER button to save the setting.

Press UP or DOWN to select the mode of Auto or Sond or dMH.

Press ENTER to save the setting.

Press Menu to upgrade the menu.

Product specificaties

Merk:	Konig
Categorie:	Effect machine
Model:	DL-DANCER250
Kleur van het product:	Zwart
Gewicht:	4300 g
Vermogen lamp:	250 W
Ingangsspanning:	230 V
Fitting/voet-type:	GX5.3
Frequentie:	50 - 60 Hz
Afmetingen (B x D x H):	365 x 365 x 195 mm