Kicker ZX450.2 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Kicker ZX450.2 (10 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 64 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/10
ZX
STEREOAMPLIFIER
ZX ZX ZX ZX350 ,.2 450 ,.2 550 ,.2 850.2
©2006 Stillwater Designs
English Version
Versión spañolE
Amplificador del la erie ZX.2S
Manual del Propietario
Deutsche Version
S Stereoverstärker der ZX.2- erie
Benutzerhandbuch
Version Française
Amplificateur de série ZX.2
Manuel d'utilisation
Installation . . . as easy as 1, 2, 3
1. Mounting Choose a structurally sound location to mount your Kicker amplifier. The controls on the
top of the amplifier need to be accessible for adjustment. Make sure there are no items behind the area
where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for
the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four
holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifier.
2. Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then connect the ground wire
to the amplifier. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and
corrosion-free solid-metal area of the vehicle's chassis. Adding an additional ground wire between the
battery's negative post and the vehicle chassis of this same gauge (or larger) is recommended.
Use a twisted pair of RCA (low-level) interconnect cable to feed the audio signal to the amplifier.
Only use speaker wire (high-level) inputs if
your source unit does not have RCA type
outputs. Either input method will provide a
low-level output signal at the RCA output,
which effectively passes the audio signal
to another amplifier or component
(P.A.S.T.). Keep the RCA cable away from
factory wiring harnesses and other power
wiring. If you need to cross this wiring,
cross it at a 90 degree angle.
Install a fuse within 18” (45cm) of the
battery and in-line with the power cable
connected to your amplifier. If you ever
need to remove the amplifier from the
vehicle after it has been installed, the ground wire should be the last wire disconnected from the
amplifier--just the opposite as when you installed it. See the chart below for power and ground wire
size, and fusing recommendations.
3. Configuration The following
diagrams show the most common
configurations for your Kicker ZX series
amplifier.
Two Channel peration ( tereo) O S These ZX amplifiers are capable of operating into a minimum
impedance of 2 ohms per channel in stereo operation. See Figure 2.
Bridged Operation (Mono) ZX.2 series amplifiers are capable of operating into a minimum
impedance of 4 ohms when in bridged operation. See Figure 3.
S O S S Stereo and Mono peration imultaneously ( AM ) The ZX.2 series amplifiers are capable of
operating into a minimum impedance of 4 ohms mono and 2 ohms per channel in stereo
simultaneously with the use of passive crossovers. See Figure 4.
INSTALLAT OI N
ZX.2AMPLIFIER
ZX ZX ZX ZX350.2 /450.2 /550.2 /850.2
TwoChannelModels:
ZX.2SeriesAmplifier
Owner’sManual
Congratulations on your
KICKER purchase
Please record your purchase
information and keep your sales
receipt for validation of warranty.
Authorized Kicker Dealer:
Purchase Date:
Amplifier Model Number:
Amplifier Serial Number:
__________________________
__________________________
__________________________
__________________________
Model FuseZX350.2 50APowerG d 8rounWire GA
Model FuseZX450.2 60APowerG d 4rounWire GA
Model FuseZX550.2 70APowerG d 4rounWire GA
Model FuseZX850.2 120APowerG drounWire 2GA
Note: To get the best performance from your new Kicker Amplifier, we recommend using genuine Kicker Accessories and Wiring.
Note: All specifications and performance figures are subject to change. Please visit the www.kicker.com for the most current information.
23
C AONFIGUR T OI N
SOURCE UNIT
killers trk7“on Top”
INPUT
RL
L -+L- R+ R
O T TU PU
RL
H E EI-L V L
INPUT
+ +- - O OFF HI L
X VO ER
REMOT E BASS
F uig re 1
U h mp f ,se onl ney o type of signal input to t e a li ier
eit le ireher C bR A Ca or S peaker W
R A aC C ble
(Lo -Lw evel)
Input
Speaker Wire
(High-Level
O t tu pu )
Speaker Wire
(High-L puevel In t)
L fe t +
L fe t -
Right -
Right +
R A aC C ble
(Lo -Lw evel)
O t tu pu
C or ss erov
Switch
Re te Bassmo
Co puntro ul O t t
24"
Or Less
(60cm)
G droun
+
_
+
_
R-
R+
L-
L+
Re temo
Tu -rn On
Battery
+12V Fuse
Right S ea erp k
L f p ke t S ea er
18"
Or Less
Signal O t u (P. . .A S T.)
(45cm)
Signal In
Mini an e 2 s er eratimum i emp d c of ohm p channel in stereo op on
Re temo
Tu -rn On
Battery
+12V Fuse
18"
Or Less
(45cm)
Mini i an e s w en in ri ge eratimum mped c of 4 ohm h b d d op on
R-
R+
L-
L+
+
_
M no o
Speaker
Signal O t u (P. . .A S T.)
Signal In
24"
Or Less
(60cm)
G droun
24"
Or Less
(60cm)
G droun
+
_
+
_+
_
HIGH PASS
CROSSOVER
HIGH PASS
CROSSOVER L WO
PAS S
C -ROSS
OVER
L f p ke t S ea er
Rig erht Speak
M no o
Speaker
R-
R+
L-
L+
Remote
Tu -rn On
Battery
+12V Fuse
18"
Or Less
(45cm)
Mini i an e s an s er annel inmum mped c of 4 ohm mono d 2 ohm p ch
stere si ltane sl t e se assi e ss erso mu ou y with h u of p v c orov
Signal Out (P. . .A S T.)
Signal In
F u ig re 2
F uig re 3
F uig re 4
Signal uO t
( . . .P A S T.)
Operation
Your Kicker ZX.2 series amplifier has three rotary controls on top and one switch on the end-panel.
Before turning on the system for the first time, turn the three rotary controls on the top of the amplifier
to the full counter-clockwise position.
1. CrossoverSwitch The crossover switch on the end-panel is for setting the internal crossover. In
the OFF position the amplifier passes
a full-range signal to the speakers.
Use the LO position when connected
to a subwoofer. The HI position
should be selected when connected
to speakers, which you do not want
to receive any sub-bass information.
Never change the crossover
"OFF/HI/LO" switch setting with the
audio system on! See Figure 1.
2. InputGainControl The input gain control is not a volume control. It matches the output of the
source unit to the input level of the amplifier. Turn the source unit up to about 3/4 volume (if the source
unit goes to 30, turn it to 25). Next, slowly turn (clockwise) the gain on the amplifier up until you can
hear audible distortion, then turn it down a little.
3. BassBoostControl The bass boost control is designed to give you increased output 0 - 18dB
at 40 Hz. The setting for this control is subjective. If you turn it up, you must go back and adjust the
input gain control to avoid clipping the amplifier.
4. CrossoverControl The setting for this control is subjective; 80Hz is a good place to start.
5. RemoteBass(Level Control) When the crossover on your ZX.2 series amplifier is set to LO pass,
you have the ability to control the output level of the amplifier remotely. To mount the remote bass level
control, simply screw the metal
bracket to the chosen location. Then
slide the housing onto the bracket
until it snaps into place. Run the
cable from the controller to the
“Remote Bass” jack on the amplifier
chassis.
TroubleShooting
If your amplifier does not appear to be
working, check the obvious things first
such as blown fuses, poor or incorrect
wiring connections, incorrect setting of
crossover switch and gain controls, etc.
There are two LEDs on the top of your
Kicker ZX series amplifier, one green and one red. When the green LED is lit this indicates the amplifier is turned on
and no trouble exists. If the green LED turns off and the red LED is lit, this indicates that the protection circuitry (SORT)
is engaged.
Green LE ,D off no output? With a Volt Ohm Meter (VOM) check the following: 1) +12 volt power terminal
(should read +12V to +16V) 2) Remote turn-on terminal (should read +12V to +16V) 3) Check for reversed power
and ground connections 4) Ground terminal, for proper conductivity.
Green LE ,D on no output? Check the following: 1) RCA connections 2) Test speaker outputs with a “known”
good speaker. 3) Substitute source unit with a “known” good source unit. 4) Check for a signal in the RCA cable
feeding the amplifier with the “AC” test position selected on the VOM meter.
R E ,ed L D on no output? 1) Amplifier is very hot. Thermal protection is engaged. Test for proper impedance at
the speaker terminals with a VOM meter (see the diagrams in this manual for minimum recommended impedance and
multiple speaker wiring suggestions). Also check for adequate airflow around the amplifier. 2) Amplifier shuts down
only while vehicle is running. Voltage protection circuitry is engaged. Voltage to the amplifier is not within the 9-16
volt operating range. Have the vehicle's charging and electrical system inspected. 3) Amplifier will only play at low
volume levels. Short circuit protection is engaged. Check for speaker wires shorted to each other or to the vehicle
chassis. Check for damaged speakers, or speaker(s) operating below the minimum recommended impedance.
No output from one channel? 1) Check the balance control on source unit 2) Check the RCA (or speaker input)
and speaker output connections for the channel 3) Swap the RCA (or speaker input) cable from left to right. If the
problem changes sides then you have a bad RCA (or speaker input) cable or source unit problem. 4) Swap the
speaker output wire from left to right. If the problem changes sides then you have a bad speaker cable, passive
crossover network and/or speaker.
Alternator noise-whining sound with engine’s RPM? 1) Check for damaged RCA (or speaker input) cable
2) Check the routing of RCA (or speaker input) cable 3) Check the source unit for proper grounding 4) Check the
gain settings and turn them down if they are set too high.
Poor stereo image or reduced bass response? Check system phasing by turning the balance control from left
to right. If there is more bass output when turned to either side, then check your speaker wiring, passive crossover
networks and speaker terminals for proper positive and negative connections. Reverse a speaker connection from
positive to negative on the stereo/subwoofer channel(s); if the bass improves, the speaker was out of phase.
If you have more questions about the installation or operation of your new KICKER product, see the Authorized
KICKER Dealer where you made your purchase. For more advice on installation, click on the SUPPORT tab on the
Kicker homepage, www.kicker.com. Choose the TECHNICAL SUPPORT tab, choose the subject you are interested in,
and then download or view the corresponding information. Please E-mail support@kicker.com or call Technical
Services (405) 624-8583 for unanswered or specific questions.
Please Note: Modern high performance speakers have a lower DC Resistance than what used to be available. The Kicker Coaxial and
Component speakers are rated at four ohms (some DC Resistances may be as low as 3 ohms) and work with any amplifier designed to
operate at a four ohm load. If you want to use two Kicker Coaxial or Component speakers on a single channel of your amplifier wire the
speakers in series. This will improve the sound quality, lower the total harmonic distortion and lessen the thermal load at the amplifier. This
may prevent an amplifier from shutting down, due to over-current protection circuitry.
CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct. Improper connections can
result in blown amplifier fuses as well as the failure of other critical systems in the vehicle.
Performance
Model ZX35 45 55 850.2 ZX 0.2 ZX 0.2 ZX 0.2
RMS Power in Watts, all channels driven
@14.4V, 4ΩStereo ≤1% THD+N 110 x 2 150 x 2 205 x 2 295 x 2
@14.4V, 2ΩStereo, ≤1% THD+N 175 x 2 225 x 2 275 x 2 425 x 2
@14.4V, 4ΩMono, ≤1% THD+N 350 x 1 450 x 1 550 x 1 850 x 1
Length: 13 1/2” (342mm) 16 3/4” (425mm) 20” (507mm) 23 1/4” (590mm)
Specifications common to all models:
Height: 2 1/8” (54mm)
Width: 9 5/8” (244mm)
Frequency Response, ± 0.5 dB: 20 Hz - 20 kHz
Signal-to-Noise Ratio: >95 dB, a-weighted, re: rated power
Input Sensitivity: 125 mV - 5 V low level, 250 mV - 10 V high level
Electronic Crossover: Variable HI, LO or OFF (bypass), 50 - 200Hz, 12dB per octave
Bass Boost: Variable 0 to +18 dB boost @ 40 Hz
ZX.2AMPLIFIER
4 5
Model .2ZX350
110 x 2 @ 4 ohms, 14.4Vdc, 1% T DH , CEA-2006 (Watts)
Signal ise Rati EA 2006 to No o -98 C - (ref: 1W, A-weighted)
Model .2ZX450
150 x 2 @ 4 ohms, 14.4Vdc, 1% T DH , CEA-2006 (Watts)
Signal ise Rati EA 2006 to No o -95 C - (ref: 1W, A-weighted)
Model .2ZX550
205 x 2 @ 4 ohms, 14.4Vdc, 1% T DH , CEA-2006 (Watts)
Signal ise Rati EA 2006 to No o -95 C - (ref: 1W, A-weighted)
Model .2ZX850
2 2 s V T D95 x @ 4 ohm , 14.4 dc, 1% H , CEA-2006 (Watts)
Signal ise Rati EA 2006 to No o -93 C - (ref: 1W, A-weighted)
P FER ORMANCE
OPERAT OI N
INPUT
RL
L L- -+ R+ R
O T TU PU
RL
H E EI-L V L
INPUT
+ - - +
O OFF HI L
X VO ER
REMOTE BASS
L-
L+
F uig re 5
C o or ss erov Contr l
5 d / c0 - 200Hz, 12 B O t
I onput Gain Contr l
Lo 5mw Level: 12 V - 5V, High Level: 2 0 V5 m - 10 V
Bass st ntr Boo Co ol
0 t B 0 o +18d boost @ 4 Hz
F u ig re 6
M t eount h metal et brack
Ba Viewck
Si Viewd e
4 Conduct ro
P ahone C ble
Sli it intd he t e housing ntil u snap so t eh metal ra et b ck
Product specificaties
| Merk: | Kicker |
| Categorie: | Autoradio |
| Model: | ZX450.2 |
Heb je hulp nodig?
Als je hulp nodig hebt met Kicker ZX450.2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Autoradio Kicker
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
Handleiding Autoradio
- Autoradio Philips
- Autoradio Sony
- Autoradio Panasonic
- Autoradio LG
- Autoradio AEG
- Autoradio Daewoo
- Autoradio Ford
- Autoradio Fiat
- Autoradio Grundig
- Autoradio JVC
- Autoradio JBL
- Autoradio Kenwood
- Autoradio Medion
- Autoradio Opel
- Autoradio Pioneer
- Autoradio Renault
- Autoradio Volvo
- Autoradio Adcom
- Autoradio Aiwa
- Autoradio Akai
- Autoradio Alpine
- Autoradio Audiosonic
- Autoradio Audiovox
- Autoradio Audison
- Autoradio Auna
- Autoradio Autovision
- Autoradio Axton
- Autoradio Becker
- Autoradio Blaupunkt
- Autoradio Boss
- Autoradio Boston Acoustics
- Autoradio Brigmton
- Autoradio Denver
- Autoradio DLS
- Autoradio Dual
- Autoradio Eclipse
- Autoradio Elta
- Autoradio Eltax
- Autoradio Emphaser
- Autoradio ESX
- Autoradio Focal
- Autoradio Fusion
- Autoradio Ground Zero
- Autoradio Harman Kardon
- Autoradio Hertz
- Autoradio Hifonics
- Autoradio Hyundai
- Autoradio Impulse
- Autoradio Lanzar
- Autoradio Lenco
- Autoradio Mac Audio
- Autoradio Macrom
- Autoradio Maginon
- Autoradio Magnat
- Autoradio Manta
- Autoradio Marquant
- Autoradio MB Quart
- Autoradio Mercedes-Benz
- Autoradio MT Logic
- Autoradio Mtx Audio
- Autoradio Muse
- Autoradio Nedis
- Autoradio Nextbase
- Autoradio Parrot
- Autoradio Phonocar
- Autoradio Pure
- Autoradio Pyle
- Autoradio Renkforce
- Autoradio Revo
- Autoradio Roadstar
- Autoradio Rockford Fosgate
- Autoradio Rodek
- Autoradio RTO
- Autoradio Sanyo
- Autoradio Scott
- Autoradio Sencor
- Autoradio Sevic
- Autoradio Silvercrest
- Autoradio Skoda
- Autoradio Smart
- Autoradio Soundstream
- Autoradio Spectron
- Autoradio Stinger
- Autoradio Tamashi
- Autoradio Technaxx
- Autoradio Telefunken
- Autoradio Telestar
- Autoradio Tevion
- Autoradio Tokai
- Autoradio Toxic
- Autoradio Twister
- Autoradio Ultimate
- Autoradio US Blaster
- Autoradio Varta
- Autoradio VDO
- Autoradio VDO Dayton
- Autoradio Vieta
- Autoradio Voxx
- Autoradio VW
- Autoradio Watssound
- Autoradio Xomax
- Autoradio Zenec
- Autoradio Jensen
- Autoradio OneConcept
- Autoradio Orion
- Autoradio Overmax
- Autoradio Clas Ohlson
- Autoradio McIntosh
- Autoradio Clatronic
- Autoradio ECG
- Autoradio Caliber
- Autoradio Krüger And Matz
- Autoradio Naxa
- Autoradio Kunft
- Autoradio Scion
- Autoradio Clarion
- Autoradio Cobra
- Autoradio Conceptronic
- Autoradio Biltema
- Autoradio Majestic
- Autoradio Trevi
- Autoradio Crunch
- Autoradio Multilaser
- Autoradio Sendai
- Autoradio Orava
- Autoradio SPC
- Autoradio Norauto
- Autoradio Lark
- Autoradio Xblitz
- Autoradio Shuttle
- Autoradio Deaf Bonce
- Autoradio Cartronix
- Autoradio Dension
- Autoradio Raveland
- Autoradio RetroSound
- Autoradio Planet Audio
- Autoradio SoundMAX
- Autoradio Mystery
Nieuwste handleidingen voor Autoradio
20 November 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024
13 November 2024