Kicker zx 550 3 Handleiding

Kicker Autoradio zx 550 3

Lees hieronder de 📖 handleiding in het Nederlandse voor Kicker zx 550 3 (10 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 37 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/10

MULTI-CHANNELAMPLIFIER

with a CLASS-DSUBWOOFERCHANNEL

ZX550.3, ZX700.5

English Version

Versión Español

Amplificador del la Serie ZX.3/ZX.5

Manual del Propietario

Deutsche Version

Stereoverstärker der ZX.3/ZX.5-Serie

Benutzerhandbuch

Version Française

Amplificateur de série ZX.3/ZX.5

Manuel d'utilisation

Installation . . . as easy as 1, 2, 3

1. Mounting Choose a structurally sound location to mount your Kicker amplifier. The controls on the

top of the amplifier need to be accessible for adjustment. Make sure there are no items behind the area

where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for

the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four

holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifier.

2. Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then connect the ground wire

to the amplifier. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and

corrosion-free solid-metal area of the vehicle's

chassis. Adding an additional ground wire between

the battery's negative post and the vehicle chassis

of this same gauge (or larger) is recommended.

Use a twisted pair(s) of RCA (low-level)

interconnect cable to feed the audio signal to the

amplifier. If you are using only one pair of RCA

inputs, connect the RCA cable to the AMP 1

inputs. All three (or five ZX700.5) channels will

work with a single pair of RCA input cable; the

fader will not operate. Keep the RCA cable away

from factory wiring harnesses and other power

wiring. If you need to cross this wiring, cross it at a

90 degree angle.

Only use speaker wire (high-level) inputs if your source unit does not have RCA type outputs. When

using both sets of high-level inputs for the ZX700.5, the supplied RCA dummy plugs must be inserted

into the RCA AMP 2 inputs in order for the fader to work properly. In any other configuration do not use

the RCA dummy plugs. Never use shorting plugs in any configuration. See Figure 1.

Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your

amplifier. If you ever need to remove the amplifier from the vehicle after it has been installed, the ground

wire should be the last wire disconnected from the amplifier--just the opposite as when you installed it.

See the chart below for power and

ground wire size, and fusing

recommendations.

3. Configuration The following diagrams show the most common configurations for your Kicker ZX

series amplifier.

Four (ZX700.5) / Two Channel (ZX550.3) Operation with Subwoofer These ZX amplifiers are

capable of operating into a minimum impedance of 2 ohms per channel in stereo operation and

2 ohms mono in the subwoofer channel. See Figure 3.

Bridged (Mono) Operation (ZX700.5) The ZX700.5 series amplifier is capable of operating into a

minimum impedance of 4 ohms when in bridged operation. This allows you to bridge AMP 1 to run the

“right” side and AMP 2 to run the “left” side. You will need two RCA Y-Adapters for this configuration.

Each AMP is stable down to 4 ohms in this configuration. See Figure 4.

INSTALLATION

ZX.3/ZX.5AMPLIFIER

ZX550.3 /ZX700.5

Multi-ChannelModels:

ZX.3/ZX.5SeriesAmplifier

Owner’sManual

Congratulations on your

KICKER purchase

Please record your purchase

information and keep your sales

receipt for validation of warranty.

Authorized Kicker Dealer:

Purchase Date:

Amplifier Model Number:

Amplifier Serial Number:

__________________________

SUB INPUT SUB

SOURCE UNIT

killers trk7“on Top”

ModelZX550.3 Fuse60APowerGroundWire 4GA

ModelZX700.5 Fuse90APowerGroundWire 4GA

Remote

Turn-On

Battery

+12V Fuse

18"

Or Less

(45cm)

24"

Or Less

(60cm)

Ground

+-+-

Signal In AMP 1

Signal In AMP 2

Left Speaker AMP 1 Right Speaker AMP 1

Minimum impedance of 2 ohms in the Subwoofer Channel

and 2 ohms per channel in stereo operation of the AMPs

Signal In Subwoofer

(Optional)

+-+

Left Speaker AMP 2 Right Speaker AMP 2

Mono Speaker

Subwoofer Channel

Remote

Turn-On

Battery

+12V Fuse

18"

Or Less

(45cm)

24"

Or Less

(60cm)

Ground

+-+-

Signal In AMP 1 (Right)

Signal In AMP 2 (Left)

Mono Speaker

Subwoofer Channel

Right Speaker AMP 1 Left Speaker AMP 2

Minimum impedance of 2 ohms in the Subwoofer Channel

and 4 ohms per AMP in bridged operation

Signal In Subwoofer

(Optional)

Figure 3

Figure 4

Use only one type of signal input to the

amplifier, either RCA Cable or Speaker Wire

RCA Cable

(Low-Level)

Speaker Wire

(High-Level

Output)

Speaker Wire

(High-Level Input)

Left +

Left -

Right -

Right +

CONFIGURATION

When using both sets of high-level

(speaker wire) inputs the supplied RCA

dummy plugs must be inserted into the

RCA AMP 2 inputs in order for

the fader to work properly.

Left +

Left -

Right -

Right +

Optional RCA

Subwoofer Cable Input

Optional RCA

Subwoofer Cable Output

Figure 1

ZX700.5

SUB INPUT

SUB

SOURCE UNIT

killers trk7“on Top”

Use only one type of signal input to the

amplifier, either RCA Cable or Speaker Wire

RCA Cable

(Low-Level)

Speaker Wire

(High-Level

Output)

Speaker Wire

(High-Level Input)

Left +

Left -

Right -

Right +

Optional RCA

Subwoofer Cable

Figure 2

ZX550.3

ZX700.5

Note: To get the best performance from your new Kicker Amplifier, we recommend using genuine Kicker Accessories and Wiring.

Note: All specifications and performance figures are subject to change. Please visit the www.kicker.com for the most current information.

Operation

Your Kicker ZX series amplifier has five (or seven ZX700.5) rotary controls on top and one

(or two ZX700.5) switch(es) on the end-panel. Before turning on the system for the first time, turn the

rotary controls on the top of the amplifier to the full counter-clockwise position.

1. CrossoverSwitch The crossover switch(es) on the end-panel is

(are) for setting the internal crossover(s) for the “full-range” audio

channels (12dB slope per octave). In the OFF position the amplifier

passes a full-range signal to the speakers. The HI position should be

selected when connected to speakers, which you do not want to

receive any sub-bass information. Never change the crossover

"OFF/HI" switch setting with the audio system on!

2. InputGainControl The input gain control is not a volume control.

It matches the output of the source unit to the input level of the

amplifier. Turn the source unit up to about 3/4 volume (if the source

unit goes to 30, turn it to 25). Next, slowly turn (clockwise) the gain

on the amplifier up until you can hear audible distortion, then turn it

down a little. Set AMP 1 first, then AMP 2 (ZX700.5 only) and finally

the Subwoofer Channel input gain control.

3. BassBoostControl The bass boost control is designed to give

you increased output 0 - 18dB at 40Hz for the subwoofer channel.

The setting for this control is subjective. If you turn it up, you must go

back and adjust the input gain control to avoid clipping the amplifier.

4. CrossoverControl The setting for this control is subjective; 80Hz is a good place to start.

5. RemoteBass(Level Control) When using the remote bass level control you have the ability to

control the level of the Subwoofer Channel’s output remotely. To mount the remote bass level control,

simply screw the metal bracket to the

chosen location. Then slide the

housing onto the bracket until it

snaps into place. Run the cable from

the controller to the “Remote Bass”

jack on the amplifier chassis.

TroubleShooting

If your amplifier does not appear to be

working, check the obvious things first

such as blown fuses, poor or incorrect

wiring connections, incorrect setting of

crossover switch and gain controls, etc.

There are two LEDs on the top of your

Kicker ZX series amplifier, one green and

one red. When the green LED is lit this indicates the amplifier is turned on and no trouble exists. If the green LED turns

off and the red LED is lit, this indicates that the protection circuitry (SORT) is engaged.

Green LED off, no output? With a Volt Ohm Meter (VOM) check the following: 1) +12 volt power terminal

(should read +12V to +16V) 2) Remote turn-on terminal (should read +12V to +16V) 3) Check for reversed power

and ground connections 4) Ground terminal, for proper conductivity

Green LED on, no output? Check the following: 1) RCA connections 2) Test speaker outputs with a “known”

good speaker. 3) Substitute source unit with a “known” good source unit. 4) Check for a signal in the RCA cable

feeding the amplifier with the “AC” test position selected on the VOM meter.

Red LED on, no output? 1) Amplifier is very hot. Thermal protection is engaged. Test for proper impedance at

the speaker terminals with a VOM meter (see the diagrams in this manual for minimum recommended impedance and

multiple speaker wiring suggestions). Also check for adequate airflow around the amplifier. 2) Amplifier shuts down

only while vehicle is running. Voltage protection circuitry is engaged. Voltage to the amplifier is not within the 9-16

volt operating range. Have the vehicle's charging and electrical system inspected. 3) Amplifier will only play at low

volume levels. Short circuit protection is engaged. Check for speaker wires shorted to each other or to the vehicle

chassis. Check for damaged speakers, or speaker(s) operating below the minimum recommended impedance.

No output from one channel? 1) Check the balance control on source unit 2) Check the RCA (or speaker input)

and speaker output connections for the channel 3) Swap the RCA (or speaker input) cable from left to right. If the

problem changes sides then you have a bad RCA (or speaker input) cable or source unit problem. 4) Swap the

speaker output wire from left to right. If the problem changes sides then you have a bad speaker cable, passive

crossover network and/or speaker.

Alternator noise-whining sound with engine’s RPM? 1) Check for damaged RCA (or speaker input) cable

2) Check the routing of RCA (or speaker input) cable 3) Check the source unit for proper grounding 4) Check the

gain settings and turn them down if they are set too high

Poor stereo image or reduced bass response? Check system phasing by turning the balance control from left

to right. If there is more bass output when turned to either side, then check your speaker wiring, passive crossover

networks and speaker terminals for proper positive and negative connections. Reverse a speaker connection from

positive to negative on the stereo/subwoofer channel(s); if the bass improves, the speaker was out of phase.

Ground-Loop Noise? If you are using only one pair of RCA inputs, connect the RCA cable to the AMP 1 inputs.

No Fader? When using both sets of high-level inputs (ZX700.5 only), RCA dummy plugs must be inserted into

the RCA AMP 2 inputs in order for the fader to work properly. If you do not have dummy plugs available, use

unterminated RCA ends or cut the ends off of existing RCA cable. Do not use shorting plugs.

If you have more questions about the installation or operation of your new KICKER product, see the Authorized KICKER Dealer where you

made your purchase. For more advice on installation, click on the SUPPORT tab on the Kicker homepage, www.kicker.com. Choose the

TECHNICAL SUPPORT tab, choose the subject you are interested in, and then download or view the corresponding information. Please

E-mail support@kicker.com or call Technical Services (405) 624-8583 for unanswered or specific questions.

Please Note: Modern high performance speakers have a lower DC Resistance than what used to be available. The Kicker Coaxial and

Component speakers are rated at four ohms (some DC Resistances may be as low as 3 ohms) and work with any amplifier designed to

operate at a four ohm load. If you want to use two Kicker Coaxial or Component speakers on a single channel of your amplifier wire the

speakers in series. This will improve the sound quality, lower the total harmonic distortion and lessen the thermal load at the amplifier. This

may prevent an amplifier from shutting down, due to over-current protection circuitry.

CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct. Improper connections can

result in blown amplifier fuses as well as the failure of other critical systems in the vehicle.

Performance

Model ZX550.3 ZX700.5

RMS Power in Watts, AMP 1 and AMP 2 all channels driven

@14.4V, 4ΩStereo ≤1% THD+N 70 x 2 70 x 4

@14.4V, 2ΩStereo, ≤1% THD+N 85 x 2 85 x 4

@14.4V, 4ΩMono, ≤1% THD+N N/A 165 x 2

RMS Power in Watts, Subwoofer channel driven

@14.4V, 4ΩMono ≤1.5% THD+N 210 x 1 210 x 1

@14.4V, 2ΩMono, ≤1.5% THD+N 420 x 1 420 x 1

Length: 16 3/4” (425mm) 20” (507mm)

Specifications common to all models:

Height: 2 1/8” (54mm)

Width: 9 5/8” (244mm)

Frequency Response, ± 0.5 dB: 20 Hz - 20 kHz

Signal-to-Noise Ratio: >95 dB, a-weighted, re: rated power

Input Sensitivity: 125 mV - 5 V low level, 250 mV - 10 V high level

Electronic Crossover: Variable (defeatable) HI pass, 50 - 200Hz, 12bB per octave, for the full-range channels

Variable LOW pass, 50 - 200Hz, 24dB per octave, for the subwoofer channel

Bass Boost: Variable 0 to +18dB boost @ 40Hz, for the subwoofer channel

ZX.3/ZX.5AMPLIFIER

4 5

Model ZX550.3

70 x 2, 210 x 1 @ 4 ohms from 20-20K, 20-200Hz, 14.4Vdc,

1% THD, CEA-2006 (Watts)

Signal to Noise Ratio -72 / -55 dBA CEA-2006 (ref: 1W, A-weighted)

Model ZX700.5

70 x 4, 210 x 1 @ 4 ohms from 20-20K, 20-200Hz, 14.4Vdc,

1% THD, CEA-2006 (Watts)

Signal to Noise Ratio -72 / -55 dBA CEA-2006 (ref: 1W, A-weighted)

PERFORMANCE

OPERATION

SUB INPUT SUB

Figure 6

Mount the metal bracket

Back View

Side View

4 Conductor

Phone Cable

Slide the housing until it snaps into the metal bracket

Figure 5

Crossover Control

Subwoofer Channel

Bass Boost Control

Subwoofer Channel

Input Gain Control

AMP 1 Input

Gain ControlAMP 2 Input

Gain Control

Crossover Control

AMP 2

Crossover Control

AMP 1

ZX700.5

Product specificaties

Merk:	Kicker
Categorie:	Autoradio
Model:	zx 550 3

Heb je hulp nodig?

Als je hulp nodig hebt met Kicker zx 550 3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Autoradio Kicker

Kicker X50 Handleiding

2 Juni 2023

Kicker zx 350 2 Handleiding

2 Juni 2023

Kicker KX 400.4 Handleiding

2 Juni 2023

Kicker ZX 300.1 Handleiding

2 Juni 2023

Kicker kx 600 1 Handleiding

2 Juni 2023

Kicker zr 120 Handleiding

2 Juni 2023

Kicker KX 800.4 Handleiding

2 Juni 2023

Kicker KX 550.2 Handleiding

2 Juni 2023

Kicker zx 550 3 Handleiding

2 Juni 2023

Kicker ix 404 impulse Handleiding

2 Juni 2023

Handleiding Autoradio

Nieuwste handleidingen voor Autoradio

Boss BCPA12 Handleiding

30 November 2024

Alpine mrp m 200 Handleiding

16 November 2024

Panasonic CQ-5250T Handleiding

23 November 2024

Deaf Bonce Machete MFA-1.1500 Handleiding

20 November 2024

Xblitz RF100 Handleiding

15 November 2024

Xblitz RF300 Handleiding

15 November 2024

Xblitz RF500 CAM Handleiding

15 November 2024

Xblitz RF350 CAM Handleiding

15 November 2024

Blaupunkt Alicante CD30 Handleiding

15 November 2024

JBL Grand Touring GTR-102 Handleiding

15 November 2024