Kicker ZX 300.1 Handleiding

Kicker Autoradio ZX 300.1

Lees hieronder de šŸ“– handleiding in het Nederlandse voor Kicker ZX 300.1 (28 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/28
ZX AMPLIFIER
ZX300.1
ZX400.1
ZX500.1
ZX750.1
English Version
VersiĆ³n EspaƱol
Amplificador del la Serie ZX.1
Deutsche Version
StereoverstƤrker der ZX.1-Serie
Version Francaise
Amplificateur de sƩrie ZX.1
LIVINā€™ LOUD
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 12011 ZX 300.1 400.1 500.1 750.1 RevC.indd 1 11/5/2010 1:22:27 PM11/5/2010 1:22:27 PM
2ZX AMPLIFIERS
ZX.1-SERIES AMPLIFIERS Ownerā€™s Manual
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER ampliļ¬ er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4ā€ (10cm) of open
ventilation for the ampliļ¬ er. If possible, mount the ampliļ¬ er in the climate-controlled passenger compartment. Drill
four holes using a 7/64ā€ (3mm) bit and use the supplied #8 screws to mount the ampliļ¬ er.
Wiring: Disconnect the vehicleā€™s battery to avoid an electrical short. Then, connect the ground wire to the
ampliļ¬ er. Make the ground wire short, 24ā€ (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicleā€™s chassis. Adding an additional ground wire of this same gauge (or larger) between the
batteryā€™s negative post and the vehicle chassis is recommended.
The ZX ampliļ¬ er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereoā€™s source unit. A high-level signal can be run from the source unitā€™s speaker outputs to the
stereo RCA input on the end panel of the ampliļ¬ er using the KICKER ZISL as shown (make sure you set the ZX
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Model Number:
Serial Number:
Model: ZX300.1 ZX400.1 ZX500.1 ZX750.1
RMS Power
@ 14.4V, 4Ī© mono, ļ‚£ 1% THD+N
@ 14.4V, 2Ī© mono, ļ‚£ 1% THD+N
150W x 1
300W x 1
200W x 1
400W x 1
250W x 1
500W x 1
375W x 1
750W x 1
Length 13-1/2ā€
(342mm)
10-1/4ā€
(260mm)
12ā€
(305mm)
14-11/16
(373mm)
Selectable Electronic Crossover Lo-pass,
80Hz,
24dB/octave
Variable lo-pass 50ā€“200Hz, 24dB/octave
Bass Boost +12dB, on/off,
40Hz
Variable 0ā€“18dB @ 40Hz
Frequency Response Ā± 1dB 25Hzā€“20kHz 25Hzā€“200Hz
Speciļ¬ cations common to all models:
Height 2-1/8ā€ (54mm)
Width 9-5/8ā€ (244mm)
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mVā€“5V
High Level: 250mVā€“10V
Subsonic Filter 24dB/octave, ļ¬ xed @ 25Hz
Pro Tip: To get the best performance from your new KICKER Ampliļ¬ er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
MODEL: ZX300.1 / ZX400.1 / ZX500.1 / ZX750.1
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 22011 ZX 300.1 400.1 500.1 750.1 RevC.indd 2 11/5/2010 1:22:35 PM11/5/2010 1:22:35 PM
3
Model External Fuse Power/Ground Wire KICKER Wiring Kit
ZX300.1 1 x 60 Ampere 8 Gauge PK8, CK8, ZCK8
ZX400.1 1 x 60 Ampere 4 Gauge PK4, CK4, ZCK4
ZX500.1 1 x 80 Ampere 4 Gauge PK4, CK4, ZCK4
ZX750.1 1 x 100 Ampere 4 Gauge PK4, CK4, ZCK4
ampliļ¬ erā€™s input level switch to ā€œHIā€). Alternatively, the signal can be delivered to the ampliļ¬ er using the low-level
RCA outputs on the source unit. Set the input level switch on the end panel of the ampliļ¬ er to ā€œLOā€. Either input
method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to
another ampliļ¬ er or component. Keep the audio signal cable away from factory wiring harnesses and other
power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to ampliļ¬ er
shield
+
ā€“
core conductor
GND REM +12V
12V
battery
external fuse
remote turn-on
(see page 5)
bare-metal
chassis ground
ļ‚£18ā€
(45cm)
ļ‚£24ā€
(60cm)
Install a fuse within 18ā€ (45cm) of the battery and in-line with the power cable connected to your ampliļ¬ er. If you
ever need to remove the ampliļ¬ er from the vehicle after it has been installed, the ground wire should be the last
wire disconnected from the ampliļ¬ er--just the opposite as when you installed it.
KICKER ZISL
source unit high-level
speaker outputs
OR to ampliļ¬ er
protection LED
2011 ZX 300.1 400.1 500.1 750.1 RevC.indd 32011 ZX 300.1 400.1 500.1 750.1 RevC.indd 3 11/5/2010 1:22:35 PM11/5/2010 1:22:35 PM


Product specificaties

Merk: Kicker
Categorie: Autoradio
Model: ZX 300.1

Heb je hulp nodig?

Als je hulp nodig hebt met Kicker ZX 300.1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Autoradio Kicker

Handleiding Autoradio

Nieuwste handleidingen voor Autoradio