Kicker ZX200.4 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Kicker ZX200.4 (10 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/10
ZX
MULTI-CHANNELAMPLIFIER
ZX200.4
©2006 Stillwater Designs
English Version
Versión spañolE
Amplificador del la Serie ZX.4
Manual del Propietario
Deutsche Version
Stereoverstärker der ZX.4-Serie
Benutzerhandbuch
Version Française
Amplificateur de série ZX.4
Manuel d'utilisation
Installation . . . as easy as 1, , 32
1. Mounting Choose a structurally sound location to mount your Kicker amplifier. The amplifier’s
end-panel controls need to be accessible for adjustment. Make sure there are no items behind the area
where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for
the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four
holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifier.
2
. Wiring
Disconnect the vehicle’s battery to avoid an electrical short. Then connect the ground wire
to the amplifier. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and
corrosion-free solid-metal area of the vehicle's
chassis.
Use a twisted pair(s) of RCA (low-level)
interconnect cable to feed the audio signal to
the amplifier. If you are using only one pair of
RCA inputs, connect the RCA cable to the AMP
1 inputs. Push the fader button out, and all four
channels will work with a single pair of RCA
input cable. Push the fader button in, when
using two pairs of RCA input cables. Keep the
RCA cable away from factory wiring harnesses
and other power wiring. If you need to cross this
wiring, cross it at a 90 degree angle.
Only use speaker wire (high-level) inputs if
your source unit does not have RCA type outputs. If you are using only one pair of high-level inputs,
connect the speaker wire to the AMP 1 input. Push the fader button out, and all four channels will work
with a single high-level input cable. Push the fader button in, when using both sets of high-level inputs.
Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your
amplifier. If you ever need to remove the amplifier from the vehicle after it has been installed, the ground
wire should be the last wire disconnected from the amplifier--just the opposite as when you installed it.
See the chart below for power and ground wire size, and fusing recommendations.
3. Configuration The following diagrams show the most common configurations for your Kicker ZX
series amplifier.
Four C
hannel Operation (Stereo)
These ZX amplifiers are capable of operating into a minimum
impedance of 2 ohms per channel in stereo operation. See Figure 2.
Bridged Operation (Mono) ZX.4 series amplifiers are capable of operating into a minimum
impedance of 4 ohms when in bridged operation. See Figure 3.
Stereo and Bridged Operation Simultaneously The ZX.4 series amplifiers are capable of operating
into a minimum impedance of 4 ohms bridged and 2 ohms per channel in stereo operation. See
Figure 4.
INSTALLATION
ZX 4AMPLIFIER
ZX200.4
FourChannelModel:
ZX.4SeriesAmplifier
Owner’sManual
Congratulations on your
KIC EK R purchase
Please record your purchase
information and keep your sales
receipt for validation of warranty.
Authorized Kicker Dealer:
Purchase Date:
Amplifier Model Number:
Amplifier Serial Number:
__________________________
__________________________
__________________________
__________________________
killers trk7“on Top”
RCA
I PN UTS
BASS
GA
INGAINBASS
R
L
R
L
HI-LEVEL
I P TN U
+ - - +
H LEI- VEL
I P TN U
+ - - +
A AMP 1 MP 2
OFF I O H L
XOVER
OFF HI O L
XOVER
F D RA E
ON OFF
Model FuseZX200.4 30APowerG d 8rounWire GA
Note: To get the best performance from your new Kicker Amplifier, we recommend using genuine Kicker Accessories and Wiring.
+
-
+-+-
+
-
Battery
+12V Fuse
Right Speaker AMP 2
Left Speaker AMP 2
18"
Or Less
(45cm)
Signal In AMP 1
Minim ance peratium imped of 2 ohms per channel in stereo o on
Signal In AMP 2
Right Speaker AMP 1
Left Speaker AMP 1
24"
Or Less
(60cm)
G droun
Rem teo
Turn-On
Battery
+12V Fuse
18"
Or Less
(45cm)
Signal In AMP 1
Minim m impe ance f hms when in bri ge peratiu d o 4 o d d o on
Signal In AMP 2
M no o Speaker AMP 1
M no o Speaker AMP 2
24"
Or Less
(60cm)
G droun
Remote
Turn-On
+
+-
-
Battery
+12V Fuse
18"
Or Less
(45cm)
Signal In AMP 1
Minim ance f ge peratium imped o 4 o hms when in brid d o on
an peratid 2 ohms per channel in stereo o on
Signal In AMP 2
Right Speaker AMP 1
M no o Speaker AMP 2
Left Speaker AMP 1
24"
Or Less
(60cm)
G droun
Remote
Turn-On
+
+
+-
-
-
23
Figure 1
Figure 2
Figure 3
Figure 4
U u ,se o only ne type of signal inp t to the amplifier
either able Speaker CR A C or Wire
R AC Cable
(L el)ow-Lev
AMP 1
Speaker Wire
(High-Level
Output)
Speaker Wire
(High-Level Input)
AMP 1
Left +
Left -
Right -
Right +
C N GU AO FI R TION
ZX200.4
Speaker Wire
(High-Level Input)
AMP 2
Fa er shd uB tto un: P in of r
2 f p t pairs o inputs, ush ou
f r a fo single pair o inputs.
R AC Cable
(L el)ow-Lev
AMP 2
Left +
Left -
Right -
Right +
Operation
Your Kicker ZX.4 series amplifier has four rotary controls and two switches on the end-panel. Before
turning on the system for the first time, turn the four rotary controls on the side of the amplifier to the full
counter-clockwise position.
1. CrossoverSwitch The crossover switches on the end-panel are for setting the internal crossovers.
In the OFF position the amplifier
passes a full-range signal to the
speakers. Use the LO position when
connected to a subwoofer. The HI
position should be selected when
connected to speakers, which you
do not want to receive any sub-bass
information. Never change the
crossover "OFF/HI/LO" switch
setting with the audio system on!
2 G. Input ainControl The input gain control is not a volume control. It matches the output of the
source unit to the input level of the amplifier. Turn the source unit up to about 3/4 volume (if the source
unit goes to 30, turn it to 25). Next, slowly turn (clockwise) the gain on the amplifier up until you can
hear audible distortion, then turn it down a little. Adjust AMP 1, then proceed to AMP 2.
3. BassBoostControl The bass boost control is designed to give you increased output 0 - 12dB
at 40 Hz. The setting for this control is subjective. If you turn it up, you must go back and adjust the
input gain control to avoid clipping the amplifier.
Trouble Shooting
If your amplifier does not appear to be working, check the obvious things first such as blown fuses,
poor or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There
are two LEDs on the top of your Kicker ZX series amplifier, one green and one red. When the green
LED is lit this indicates the amplifier is turned on and no trouble exists. If the green LED turns off and
the red LED is lit, this indicates that the protection circuitry (SORT) is engaged.
Green LED off, no output? With a Volt Ohm Meter (VOM) check the following: 1) +12 volt power
terminal (should read +12V to +16V) 2) Remote turn-on terminal (should read +12V to +16V)
3) Check for reversed power and ground connections 4) Ground terminal, for proper conductivity.
Green LED on, no output? Check the following: 1) RCA connections 2) Test speaker outputs
with a “known” good speaker. 3) Substitute source unit with a “known” good source unit. 4) Check
for a signal in the RCA cable feeding the amplifier with the “AC” test position selected on the VOM
meter.
Red LED on, no output? 1) Amplifier is very hot. Thermal protection is engaged. Test for proper
impedance at the speaker terminals with a VOM meter (see the diagrams in this manual for minimum
recommended impedance and multiple speaker wiring suggestions). Also check for adequate airflow
around the amplifier. 2) Amplifier shuts down only while vehicle is running. Voltage protection
circuitry is engaged. Voltage to the amplifier is not within the 9-16 volt operating range. Have the
vehicle's charging and electrical system inspected. 3) Amplifier will only play at low volume levels.
Short circuit protection is engaged. Check for speaker wires shorted to each other or to the vehicle
chassis. Check for damaged speakers, or speaker(s) operating below the minimum recommended
impedance.
No output from one channel? 1) Check the balance control on source unit 2) Check the RCA (or
speaker input) and speaker output connections for the channel 3) Swap the RCA (or speaker input)
cable from left to right. If the problem changes sides then you have a bad RCA (or speaker input) cable
or source unit problem. 4) Swap the speaker output wire from left to right. If the problem changes
sides then you have a bad speaker cable, passive crossover network and/or speaker.
Alternator noise-whining sound with engine’s RPM? 1) Check for damaged RCA (or speaker
input) cable 2) Check the routing of RCA (or speaker input) cable 3) Check the source unit for proper
grounding 4) Check the gain settings and turn them down if they are set too high.
Poor stereo image or reduced bass response? Check system phasing by turning the balance
control from left to right. If there is more bass output when turned to either side, then check your
speaker wiring, passive crossover networks and speaker terminals for proper positive and negative
connections. Reverse a speaker connection from positive to negative on the stereo/subwoofer
channel(s); if the bass improves, the speaker was out of phase.
G L Nround- oop oise? If you are using only one pair of RCA inputs, connect the RCA cable to the
AMP 1 inputs.
No Fader? When using both sets of low-level (RCA) or high-level (speaker wire) inputs, the fader
button must be pushed in.
If you have more questions about the installation or operation of your new KICKER product, see the
Authorized KICKER Dealer where you made your purchase. For more advice on installation, click on the
SUPPORT tab on the Kicker homepage, www.kicker.com. Choose the TECHNICAL SUPPORT tab,
choose the subject you are interested in, and then download or view the corresponding information.
Please E-mail support@kicker.com or call Technical Services (405) 624-8583 for unanswered or specific
questions.
Please Note: Modern high performance speakers have a lower DC Resistance than what used to be available. The
Kicker Coaxial and Component speakers are rated at four ohms (some DC Resistances may be as low as 3 ohms)
and work with any amplifier designed to operate at a four ohm load. If you want to use two Kicker Coaxial or
Component speakers on a single channel of your amplifier wire the speakers in series. This will improve the sound
quality, lower the total harmonic distortion and lessen the thermal load at the amplifier. This may prevent an amplifier
from shutting down, due to over-current protection circuitry.
CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct. Improper
connections can result in blown amplifier fuses as well as the failure of other critical systems in the vehicle.
Performance
Model ZX200.4
RMS Power in Watts, all channels driven
@ 14.4 Volts, 4Ωstereo, ≤1% THD+N 35 x 4
@ 2 1% THD+N 50 x 4Ωstereo, ≤
@ 4 1% THD+N 100 x 2Ωmono, ≤
Frequency Response, ±0.5 dB: 20 Hz - 20 kHz
Signal-to-Noise Ratio: 95 dB, a-weighted, re: rated power>
Input Sensitivity: 125 mV - 5 V low level
250 mV - 10 V high level
Electronic Crossover: HI, LO or OFF (bypass),
fixed @ 80 Hz, 12 dB per octave
Bass Boost: Variable 0 to +12 dB boost @ 40 Hz
Height: 2 1/8” (54mm)
Width: 9 5/8” (244mm)
Length: 10 1/4” (260mm)
ZX 4AMPLIFIER
AMP 1
Bass Boo Cost ntrol
0-12 dB @ 4 H0 z
AMP 2
Bass Boo Cost ntrol
0-12 dB @ 4 H0 z
Inp ain ntru Gt Co ol AMP 1 Inp ntru Gt ain Co ol AMP 2
Selectable AMP 2
C or ssover Switch
Set @ 8 H0 z
Selectable AMP 1
C or ssover Switch
Set @ 8 H0 z
RCA
I PN UTS
BASS
GA
INGAINBASS
R
L
R
L
HI-LEVEL
I P TN U
+ - - +
H ELI-LEV
I P TN U
+ - - +
A AMP 1 MP 2
OFF HI LO
XOVER
OFF HI O L
XOVER
F D RA E
ON OFF
45
Figure 5
PERFORMANCE
OPE AR TION
Model .4ZX200
3 d H ,5 x 4 @ 4 ohms, 14.4V c, 1% T D
CEA-2006 W( atts)
Signal ise Rati to No o - 58
CE : A-2006 (ref 1W, A-weighted)
NOTE: All specifications and performance figures are subject to change. Please visit the www.kicker.com for the most current information.
Product specificaties
| Merk: | Kicker |
| Categorie: | Autoradio |
| Model: | ZX200.4 |
Heb je hulp nodig?
Als je hulp nodig hebt met Kicker ZX200.4 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Autoradio Kicker
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
Handleiding Autoradio
- Autoradio Philips
- Autoradio Sony
- Autoradio Panasonic
- Autoradio LG
- Autoradio AEG
- Autoradio Daewoo
- Autoradio Ford
- Autoradio Fiat
- Autoradio Grundig
- Autoradio JVC
- Autoradio JBL
- Autoradio Kenwood
- Autoradio Medion
- Autoradio Opel
- Autoradio Pioneer
- Autoradio Renault
- Autoradio Volvo
- Autoradio Adcom
- Autoradio Aiwa
- Autoradio Akai
- Autoradio Alpine
- Autoradio Audiosonic
- Autoradio Audiovox
- Autoradio Audison
- Autoradio Auna
- Autoradio Autovision
- Autoradio Axton
- Autoradio Becker
- Autoradio Blaupunkt
- Autoradio Boss
- Autoradio Boston Acoustics
- Autoradio Brigmton
- Autoradio Denver
- Autoradio DLS
- Autoradio Dual
- Autoradio Eclipse
- Autoradio Elta
- Autoradio Eltax
- Autoradio Emphaser
- Autoradio ESX
- Autoradio Focal
- Autoradio Fusion
- Autoradio Ground Zero
- Autoradio Harman Kardon
- Autoradio Hertz
- Autoradio Hifonics
- Autoradio Hyundai
- Autoradio Impulse
- Autoradio Lanzar
- Autoradio Lenco
- Autoradio Mac Audio
- Autoradio Macrom
- Autoradio Maginon
- Autoradio Magnat
- Autoradio Manta
- Autoradio Marquant
- Autoradio MB Quart
- Autoradio Mercedes-Benz
- Autoradio MT Logic
- Autoradio Mtx Audio
- Autoradio Muse
- Autoradio Nedis
- Autoradio Nextbase
- Autoradio Parrot
- Autoradio Phonocar
- Autoradio Pure
- Autoradio Pyle
- Autoradio Renkforce
- Autoradio Revo
- Autoradio Roadstar
- Autoradio Rockford Fosgate
- Autoradio Rodek
- Autoradio RTO
- Autoradio Sanyo
- Autoradio Scott
- Autoradio Sencor
- Autoradio Sevic
- Autoradio Silvercrest
- Autoradio Skoda
- Autoradio Smart
- Autoradio Soundstream
- Autoradio Spectron
- Autoradio Stinger
- Autoradio Tamashi
- Autoradio Technaxx
- Autoradio Telefunken
- Autoradio Telestar
- Autoradio Tevion
- Autoradio Tokai
- Autoradio Toxic
- Autoradio Twister
- Autoradio Ultimate
- Autoradio US Blaster
- Autoradio Varta
- Autoradio VDO
- Autoradio VDO Dayton
- Autoradio Vieta
- Autoradio Voxx
- Autoradio VW
- Autoradio Watssound
- Autoradio Xomax
- Autoradio Zenec
- Autoradio Jensen
- Autoradio OneConcept
- Autoradio Orion
- Autoradio Overmax
- Autoradio Clas Ohlson
- Autoradio McIntosh
- Autoradio Clatronic
- Autoradio ECG
- Autoradio Caliber
- Autoradio Krüger And Matz
- Autoradio Naxa
- Autoradio Kunft
- Autoradio Scion
- Autoradio Clarion
- Autoradio Cobra
- Autoradio Conceptronic
- Autoradio Biltema
- Autoradio Majestic
- Autoradio Trevi
- Autoradio Crunch
- Autoradio Multilaser
- Autoradio Sendai
- Autoradio Orava
- Autoradio SPC
- Autoradio Norauto
- Autoradio Lark
- Autoradio Xblitz
- Autoradio Shuttle
- Autoradio Deaf Bonce
- Autoradio Cartronix
- Autoradio Dension
- Autoradio Raveland
- Autoradio RetroSound
- Autoradio Planet Audio
- Autoradio SoundMAX
- Autoradio Mystery
Nieuwste handleidingen voor Autoradio
20 November 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024
13 November 2024