Kicker zx 550 2 Handleiding

Kicker Autoradio zx 550 2

Lees hieronder de 📖 handleiding in het Nederlandse voor Kicker zx 550 2 (10 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/10

STEREOAMPLIFIER

ZX350.2, ZX450.2, ZX550.2, ZX850.2

English Version

Versión Español

Amplificador del la Serie ZX.2

Manual del Propietario

Deutsche Version

Stereoverstärker der ZX.2-Serie

Benutzerhandbuch

Version Française

Amplificateur de série ZX.2

Manuel d'utilisation

Installation . . . as easy as 1, 2, 3

1. Mounting Choose a structurally sound location to mount your Kicker amplifier. The controls on the

top of the amplifier need to be accessible for adjustment. Make sure there are no items behind the area

where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for

the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four

holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifier.

2. Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then connect the ground wire

to the amplifier. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and

corrosion-free solid-metal area of the vehicle's chassis. Adding an additional ground wire between the

battery's negative post and the vehicle chassis of this same gauge (or larger) is recommended.

Use a twisted pair of RCA (low-level) interconnect cable to feed the audio signal to the amplifier.

Only use speaker wire (high-level) inputs if

your source unit does not have RCA type

outputs. Either input method will provide a

low-level output signal at the RCA output,

which effectively passes the audio signal

to another amplifier or component

(P.A.S.T.). Keep the RCA cable away from

factory wiring harnesses and other power

wiring. If you need to cross this wiring,

cross it at a 90 degree angle.

Install a fuse within 18” (45cm) of the

battery and in-line with the power cable

connected to your amplifier. If you ever

need to remove the amplifier from the

vehicle after it has been installed, the ground wire should be the last wire disconnected from the

amplifier--just the opposite as when you installed it. See the chart below for power and ground wire

size, and fusing recommendations.

3. Configuration The following

diagrams show the most common

configurations for your Kicker ZX series

amplifier.

Two Channel Operation (Stereo) These ZX amplifiers are capable of operating into a minimum

impedance of 2 ohms per channel in stereo operation. See Figure 2.

Bridged Operation (Mono) ZX.2 series amplifiers are capable of operating into a minimum

impedance of 4 ohms when in bridged operation. See Figure 3.

Stereo and Mono Operation Simultaneously (SAMS) The ZX.2 series amplifiers are capable of

operating into a minimum impedance of 4 ohms mono and 2 ohms per channel in stereo

simultaneously with the use of passive crossovers. See Figure 4.

INSTALLATION

ZX.2AMPLIFIER

ZX350.2 /ZX450.2 /ZX550.2 /ZX850.2

TwoChannelModels:

ZX.2SeriesAmplifier

Owner’sManual

Congratulations on your

KICKER purchase

Please record your purchase

information and keep your sales

receipt for validation of warranty.

Authorized Kicker Dealer:

Purchase Date:

Amplifier Model Number:

Amplifier Serial Number:

__________________________

ModelZX350.2 Fuse50APowerGroundWire 8GA

ModelZX450.2 Fuse60APowerGroundWire 4GA

ModelZX550.2 Fuse70APowerGroundWire 4GA

ModelZX850.2 Fuse120APowerGroundWire 2GA

Note: To get the best performance from your new Kicker Amplifier, we recommend using genuine Kicker Accessories and Wiring.

Note: All specifications and performance figures are subject to change. Please visit the www.kicker.com for the most current information.

CONFIGURATION

SOURCE UNIT

killers trk7“on Top”

INPUT

L+L- R+ R-

OUTPUT

HI-LEVEL

INPUT

+ - - + OFF HI LO

XOVER

REMOTE BASS

Figure 1

Use only one type of signal input to the amplifier,

either RCA Cable or Speaker Wire

RCA Cable

(Low-Level)

Input

Speaker Wire

(High-Level

Output)

Speaker Wire

(High-Level Input)

Left +

Left -

Right -

Right +

RCA Cable

(Low-Level)

Output

Crossover

Switch

Remote Bass

Control Output

24"

Or Less

(60cm)

Ground

R-

R+

L-

L+

Remote

Turn-On

Battery

+12V Fuse

Right Speaker

Left Speaker

18"

Or Less

Signal Out (P.A.S.T.)

(45cm)

Signal In

Minimum impedance of 2 ohms per channel in stereo operation

Remote

Turn-On

Battery

+12V Fuse

18"

Or Less

(45cm)

Minimum impedance of 4 ohms when in bridged operation

R-

R+

L-

L+

Mono

Speaker

Signal Out (P.A.S.T.)

Signal In

24"

Or Less

(60cm)

Ground

24"

Or Less

(60cm)

Ground

HIGH PAS S

CROSSOVER

HIGH PAS S

CROSSOVER LOW

PAS S

CROSS-

OVER

Left Speaker

Right Speaker

Mono

Speaker

R-

R+

L-

L+

Remote

Turn-On

Battery

+12V Fuse

18"

Or Less

(45cm)

Minimum impedance of 4 ohms mono and 2 ohms per channel in

stereo simultaneously with the use of passive crossovers

Signal Out (P.A.S.T.)

Signal In

Figure 2

Figure 3

Figure 4

Signal Out

(P.A.S.T.)

Operation

Your Kicker ZX.2 series amplifier has three rotary controls on top and one switch on the end-panel.

Before turning on the system for the first time, turn the three rotary controls on the top of the amplifier

to the full counter-clockwise position.

1. CrossoverSwitch The crossover switch on the end-panel is for setting the internal crossover. In

the OFF position the amplifier passes

a full-range signal to the speakers.

Use the LO position when connected

to a subwoofer. The HI position

should be selected when connected

to speakers, which you do not want

to receive any sub-bass information.

Never change the crossover

"OFF/HI/LO" switch setting with the

audio system on! See Figure 1.

2. InputGainControl The input gain control is not a volume control. It matches the output of the

source unit to the input level of the amplifier. Turn the source unit up to about 3/4 volume (if the source

unit goes to 30, turn it to 25). Next, slowly turn (clockwise) the gain on the amplifier up until you can

hear audible distortion, then turn it down a little.

3. BassBoostControl The bass boost control is designed to give you increased output 0 - 18dB

at 40 Hz. The setting for this control is subjective. If you turn it up, you must go back and adjust the

input gain control to avoid clipping the amplifier.

4. CrossoverControl The setting for this control is subjective; 80Hz is a good place to start.

5. RemoteBass(Level Control) When the crossover on your ZX.2 series amplifier is set to LO pass,

you have the ability to control the output level of the amplifier remotely. To mount the remote bass level

control, simply screw the metal

bracket to the chosen location. Then

slide the housing onto the bracket

until it snaps into place. Run the

cable from the controller to the

“Remote Bass” jack on the amplifier

chassis.

TroubleShooting

If your amplifier does not appear to be

working, check the obvious things first

such as blown fuses, poor or incorrect

wiring connections, incorrect setting of

crossover switch and gain controls, etc.

There are two LEDs on the top of your

Kicker ZX series amplifier, one green and one red. When the green LED is lit this indicates the amplifier is turned on

and no trouble exists. If the green LED turns off and the red LED is lit, this indicates that the protection circuitry (SORT)

is engaged.

Green LED off, no output? With a Volt Ohm Meter (VOM) check the following: 1) +12 volt power terminal

(should read +12V to +16V) 2) Remote turn-on terminal (should read +12V to +16V) 3) Check for reversed power

and ground connections 4) Ground terminal, for proper conductivity.

Green LED on, no output? Check the following: 1) RCA connections 2) Test speaker outputs with a “known”

good speaker. 3) Substitute source unit with a “known” good source unit. 4) Check for a signal in the RCA cable

feeding the amplifier with the “AC” test position selected on the VOM meter.

Red LED on, no output? 1) Amplifier is very hot. Thermal protection is engaged. Test for proper impedance at

the speaker terminals with a VOM meter (see the diagrams in this manual for minimum recommended impedance and

multiple speaker wiring suggestions). Also check for adequate airflow around the amplifier. 2) Amplifier shuts down

only while vehicle is running. Voltage protection circuitry is engaged. Voltage to the amplifier is not within the 9-16

volt operating range. Have the vehicle's charging and electrical system inspected. 3) Amplifier will only play at low

volume levels. Short circuit protection is engaged. Check for speaker wires shorted to each other or to the vehicle

chassis. Check for damaged speakers, or speaker(s) operating below the minimum recommended impedance.

No output from one channel? 1) Check the balance control on source unit 2) Check the RCA (or speaker input)

and speaker output connections for the channel 3) Swap the RCA (or speaker input) cable from left to right. If the

problem changes sides then you have a bad RCA (or speaker input) cable or source unit problem. 4) Swap the

speaker output wire from left to right. If the problem changes sides then you have a bad speaker cable, passive

crossover network and/or speaker.

Alternator noise-whining sound with engine’s RPM? 1) Check for damaged RCA (or speaker input) cable

2) Check the routing of RCA (or speaker input) cable 3) Check the source unit for proper grounding 4) Check the

gain settings and turn them down if they are set too high.

Poor stereo image or reduced bass response? Check system phasing by turning the balance control from left

to right. If there is more bass output when turned to either side, then check your speaker wiring, passive crossover

networks and speaker terminals for proper positive and negative connections. Reverse a speaker connection from

positive to negative on the stereo/subwoofer channel(s); if the bass improves, the speaker was out of phase.

If you have more questions about the installation or operation of your new KICKER product, see the Authorized

KICKER Dealer where you made your purchase. For more advice on installation, click on the SUPPORT tab on the

Kicker homepage, www.kicker.com. Choose the TECHNICAL SUPPORT tab, choose the subject you are interested in,

and then download or view the corresponding information. Please E-mail support@kicker.com or call Technical

Services (405) 624-8583 for unanswered or specific questions.

Please Note: Modern high performance speakers have a lower DC Resistance than what used to be available. The Kicker Coaxial and

Component speakers are rated at four ohms (some DC Resistances may be as low as 3 ohms) and work with any amplifier designed to

operate at a four ohm load. If you want to use two Kicker Coaxial or Component speakers on a single channel of your amplifier wire the

speakers in series. This will improve the sound quality, lower the total harmonic distortion and lessen the thermal load at the amplifier. This

may prevent an amplifier from shutting down, due to over-current protection circuitry.

CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct. Improper connections can

result in blown amplifier fuses as well as the failure of other critical systems in the vehicle.

Performance

Model ZX350.2 ZX450.2 ZX550.2 ZX850.2

RMS Power in Watts, all channels driven

@14.4V, 4ΩStereo ≤1% THD+N 110 x 2 150 x 2 205 x 2 295 x 2

@14.4V, 2ΩStereo, ≤1% THD+N 175 x 2 225 x 2 275 x 2 425 x 2

@14.4V, 4ΩMono, ≤1% THD+N 350 x 1 450 x 1 550 x 1 850 x 1

Length: 13 1/2” (342mm) 16 3/4” (425mm) 20” (507mm) 23 1/4” (590mm)

Specifications common to all models:

Height: 2 1/8” (54mm)

Width: 9 5/8” (244mm)

Frequency Response, ± 0.5 dB: 20 Hz - 20 kHz

Signal-to-Noise Ratio: >95 dB, a-weighted, re: rated power

Input Sensitivity: 125 mV - 5 V low level, 250 mV - 10 V high level

Electronic Crossover: Variable HI, LO or OFF (bypass), 50 - 200Hz, 12dB per octave

Bass Boost: Variable 0 to +18 dB boost @ 40 Hz

ZX.2AMPLIFIER

4 5

Model ZX350.2

110 x 2 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)

Signal to Noise Ratio -98 CEA-2006 (ref: 1W, A-weighted)

Model ZX450.2

150 x 2 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)

Signal to Noise Ratio -95 CEA-2006 (ref: 1W, A-weighted)

Model ZX550.2

205 x 2 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)

Signal to Noise Ratio -95 CEA-2006 (ref: 1W, A-weighted)

Model ZX850.2

295 x 2 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)

Signal to Noise Ratio -93 CEA-2006 (ref: 1W, A-weighted)

PERFORMANCE

OPERATION

INPUT

L+L- R+ R-

OUTPUT

HI-LEVEL

INPUT

+ - - + OFF HI LO

XOVER

REMOTE BASS

L-

L+

Figure 5

Crossover Control

50 - 200Hz, 12dB/Oct

Input Gain Control

Low Level: 125mV - 5V, High Level: 250mV - 10 V

Bass Boost Control

0 to +18dB boost @ 40Hz

Figure 6

Mount the metal bracket

Back View

Side View

4 Conductor

Phone Cable

Slide the housing until it snaps into the metal bracket

Product specificaties

Merk:	Kicker
Categorie:	Autoradio
Model:	zx 550 2

Heb je hulp nodig?

Als je hulp nodig hebt met Kicker zx 550 2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Autoradio Kicker

Kicker X50 Handleiding

2 Juni 2023

Kicker zx 350 2 Handleiding

2 Juni 2023

Kicker KX 400.4 Handleiding

2 Juni 2023

Kicker ZX 300.1 Handleiding

2 Juni 2023

Kicker kx 600 1 Handleiding

2 Juni 2023

Kicker zr 120 Handleiding

2 Juni 2023

Kicker KX 800.4 Handleiding

2 Juni 2023

Kicker KX 550.2 Handleiding

2 Juni 2023

Kicker zx 550 3 Handleiding

2 Juni 2023

Kicker ix 404 impulse Handleiding

2 Juni 2023

Handleiding Autoradio

Nieuwste handleidingen voor Autoradio

Deaf Bonce Machete MFA-1.1500 Handleiding

20 November 2024

Xblitz RF100 Handleiding

15 November 2024

Xblitz RF300 Handleiding

15 November 2024

Xblitz RF500 CAM Handleiding

15 November 2024

Xblitz RF350 CAM Handleiding

15 November 2024

Blaupunkt Alicante CD30 Handleiding

15 November 2024

JBL Grand Touring GTR-102 Handleiding

15 November 2024

Alpine CDA-7842R Handleiding

15 November 2024

Shuttle SCD-420 Handleiding

15 November 2024

JBL Celebrity 150 Handleiding

13 November 2024