Kicker KXMA400.4 Handleiding

Kicker Receiver KXMA400.4

Lees hieronder de 📖 handleiding in het Nederlandse voor Kicker KXMA400.4 (11 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/11
KXMA400.2 | KXMA1200.2
KXMA400.4
Manual del Propietario | Español
AMPLIFICADOR DEL LA SERIE KXM.2
Benutzerhandbuch | Deutsch
STEREOVERSTÄRKER DER KXM.2-SERIE
Manuel d’utilisation | Française
AMPLIFICATEUR DE SÉRIE KXM.2
KXM
AMPLIFIERS
Owner’s Manual
2
KXM STEREO-SERIES AMPLIFIERS
OWNER’S MANUAL
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER ampli er. Make sure there are no
items behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm)
of open ventilation for the ampli er. If possible, mount the ampli er in the climate-controlled passenger
compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the
ampli er.
Wiring: The KXM ampli ers RCA inputs will receive either high or low level signals from your car stereo’s
source unit. A high-level signal can be run from the source unit’s speaker outputs to the stereo RCA
input on the end panel of the ampli er using the KICKER KISL as shown. Alternatively, the signal can be
delivered to the ampli er using the low-level RCA outputs on the source unit. Keep the audio signal cable
away from factory wiring harnesses and other power wiring. If you need to cross this wiring, cross it at a
90 degree angle.
PERFORMANCE
MODEL: KXMA400.2 | KXMA1200.2 | KXMA400.4
IMPORTANT SAFETY WARNING
PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER, SPEAKER, OR SUBWOOFER
IN A DISTORTED, CLIPPED OR OVER-POWERED MANNER CAN CAUSE YOUR AUDIO
SYSTEM TO OVERHEAT, POSSIBLY CATCHING FIRE AND RESULTING IN SERIOUS
DAMAGE TO YOUR COMPONENTS AND/OR VEHICLE. AMPLIFIERS REQUIRE UP TO 4
INCHES (10CM) OPEN VENTILATION. SUBWOOFERS SHOULD BE MOUNTED WITH AT
LEAST 1 INCH (2.5CM) CLEARANCE BETWEEN THE FRONT OF THE SPEAKER AND ANY
SURFACE.
Model: KXMA400.2 KXMA1200.2 KXMA400.4
RMS Power
@ 14.4V, 4 stereo, ≤ 1% THD+N
@ 14.4V, 2 stereo, ≤ 1% THD+N
@ 14.4V, 4Ω mono,1% THD+N
100 x 2
200 x 2
400 x 1
300 x 2
600 x 2
N/A
50 x 4
100 x 4
200 x 2
Length [in, cm] 9-9/16, 24.4 11-3/16, 28.4 11-3/16, 28.4
Speci cations common to all models:
Height [in, cm] 2-1/8, 5.5
Width [in, cm] 8-5/16, 21
Frequency Response [Hz] 10Hz–20kHz
Signal-to-Noise Ratio [dB] 95dB
Input Sensitivity 250mV–10V
Selectable Electronic Crossover Off; Variable HP, 10–500Hz; Variable LP, 40–500Hz; 400Hz–5,000Hz
with 10X Switch (bandpass capable); Slope: 24dB/octave"
KickEQ™ Bass Boost 0–18dB @ 40Hz
3
Install a fuse within 7” (18cm) of the battery and in-line with the power cable connected to your ampli er.
POWER WIRING
source unit
high-level speaker
outputs
to ampli er
shield
+
core conductor KICKER KISL (optional)
from source unit high-
level speaker outputs
OR
to ampli er
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
KXMA400.2 1 x 60 Ampere 8 Gauge PK8, CK8
KXMA1200.2 1 x 150 Ampere 4 Gauge PK4, CK4
KXMA400.4 1 x 100 Ampere 4 Gauge PK4, CK4
RADIO
DETECT
12V
battery
external fuse
remote turn-on (see page 6)
≤7”
(18cm)
ABYC-compliant power terminals
Ampli er uses 304-stainless steel screws
and conformal coated PCB for increased
weather resistance
aluminum bottom plate


Product specificaties

Merk: Kicker
Categorie: Receiver
Model: KXMA400.4

Heb je hulp nodig?

Als je hulp nodig hebt met Kicker KXMA400.4 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Kicker

Handleiding Receiver

Nieuwste handleidingen voor Receiver