Kicker KXMA1200.1 Handleiding

Kicker Receiver KXMA1200.1

Lees hieronder de 📖 handleiding in het Nederlandse voor Kicker KXMA1200.1 (14 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 55 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/14
KXMA1200.1
Manual del Propietario | Español
AMPLIFICADOR DEL LA SERIE KXM.1
Benutzerhandbuch | Deutsch
MONOVERSTÄRKER DER KXM.1-SERIE
Manuel d’utilisation | Française
AMPLIFICATEUR DE SÉRIE KXM.1
KXM
AMPLIFIERS
Owner’s Manual
2
KXM.1-SERIES AMPLIFIERS
OWNER’S MANUAL
INSTALLATION
Mounting: Choose a dry, structurally sound location to mount your KICKER ampli er. Make sure there
are no items behind the area where the screws will be driven. Choose a location that allows at least 4
(10cm) of open ventilation for the ampli er. Drill four holes using a 7/64 (3mm) bit and use the supplied
#8 screws to mount the ampli er.
Wiring: The KXM ampli ers RCA inputs will receive either high or low level signals from your car stereo’s
source unit. A high-level signal can be run from the source units speaker outputs to the stereo RCA
input on the end panel of the amplifi er using the KICKER KISL as shown. Alternatively, the signal can be
delivered to the ampli er using the low-level RCA outputs on the source unit. Keep the audio signal cable
away from factory wiring harnesses and other power wiring. If you need to cross this wiring, cross it at a
90 degree angle.
PERFORMANCE
MODEL: KXMA1200.1
IMPORTANT SAFETY WARNING
PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER, SPEAKER, OR SUBWOOFER IN A DISTORTED, CLIPPED
OR OVER-POWERED MANNER CAN CAUSE YOUR AUDIO SYSTEM TO OVERHEAT, POSSIBLY CATCHING FIRE
AND RESULTING IN SERIOUS DAMAGE TO YOUR COMPONENTS AND/OR VEHICLE. AMPLIFIERS REQUIRE UP TO
4 INCHES (10CM) OPEN VENTILATION. SUBWOOFERS SHOULD BE MOUNTED WITH AT LEAST 1 INCH (2.5CM)
CLEARANCE BETWEEN THE FRONT OF THE SPEAKER AND ANY SURFACE.
NOTE: 2017 KXM amplifi er subwoofer channels are stable - power rating equivalent to operation, +/- 10%
Model: KXMA1200.1
RMS Power
@ 14.4V, 4Ω mono, 1% THD+N
@ 14.4V, 2Ω mono, 1% THD+N
600W x 1
1200W x 1
Length [in, cm] 9-9/16,24.4
Height [in, cm] 2 1/8, 5.5
Width [in, cm] 8 5/16, 21
Frequency Response ± 1dB 10Hz–160Hz
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity 250mV–10V
Selectable Electronic Crossover Variable Lo-pass 40Hz–160Hz, 24dB/octave
KickEQ+Parametric Bass Boost Boost - Variable 0–18db; Center Frequency - 20Hz–80Hz; Bandwidth 1–5
Subsonic Filter Variable 10–80Hz, 24dB/octave
3
Install a fuse within 7” (18cm) of the battery and in-line with the power cable connected to your ampli er.
source unit
high-level speaker
outputs
to ampli er
shield
+
core conductor KICKER KISL (optional)
from source unit high-
level speaker outputs
OR
to ampli er
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
KXMA1200.11 x 150 Ampere 4 Gauge PK4, CK4
12V
RADIO
DETECT
battery
external fuse
remote turn-on (see page 5)
woofer
MONO OPERATION
minimum impedance of 1 ohm
ABYC-compliant power terminals
Ampli er uses 304-stainless steel screws
and conformal coated PCB for increased
weather resistance
aluminum bottom plate
≤7”
(18cm)


Product specificaties

Merk: Kicker
Categorie: Receiver
Model: KXMA1200.1

Heb je hulp nodig?

Als je hulp nodig hebt met Kicker KXMA1200.1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Kicker

Handleiding Receiver

Nieuwste handleidingen voor Receiver