Kicker KX600.4 Handleiding

Kicker Autoradio KX600.4

Lees hieronder de đź“– handleiding in het Nederlandse voor Kicker KX600.4 (12 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 50 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/12
Congratulations! You have just purchased the latest in amplifier tech-
nology to carry the famous KICKER name. Your KICKER KX series
amplifier is designed and built to give you years of powerful and trou-
ble-free performance. This installation manual contains valuable infor-
mation on how to get the most out of your new KX series amplifier.
Thanks for buying KICKER. Enjoy!
KX Amplifier Features
Low Impedance Operation Stable into 2 ohm stereo or 4 ohm mono loads.
SORT Protection Circuitry ( ver-voltage, Short circuit, O Reverse polarity,
Thermal) Protects amplifier from accidents and undesired operation.
MOSFET Power Supply Provides high efficiency operation.
KickBass Variable bass boost circuit which provides up to 18 dB of boost at 40
Hz.
Built-In Variable Crossover 12 dB High pass or Low pass variable from 50-
200 Hz. Defeatable for full range operation.
High & Low level inputs Allows connection to various sources such as: after-
market stereo, factory radio, DVD Player, Video Cassette Player, etc..
Custom tooled gold plated connectors Assure maximum power transfer
and damping.
SAMS S A M S( tereo nd ono imultaneously) Amplifier will operate into a bridged
mono load and a stereo load at the same time.
Remote Bass Level Control Dash mounted for maximum control.
(Not included in the KX300.4)
Two Year Warranty When
purchased from and installed by
an Authorized
KICKER Dealer.
KX300.4 / KX600.4 / KX800.4
2
With the shroud removed, you now have access to the four mounting holes in
the mounting feet and all wiring connections. Drill 4 holes using a 7/64” drill bit
and use the supplied #8 screws to mount the amplifier.
REMOVE REMOVE
REMOVE
REMOVE
Mounting Instructions
When selecting a location to mount your Kicker amplifier be sure it is struc-
turally sound and that there are no items behind the area that could be dam-
aged by the screws. Check for brake lines, fuel lines, gas tanks, or wiring harness-
es etc.
All amplifiers generate heat under normal operation. Be sure to choose a loca-
tion that allows adequate ventilation for the amplifier. Also consider that the air
temperature inside an automobiles trunk can reach upwards of 140 degrees
fahrenheit. An amplifier mounted here may require additional cooling tactics
such as fans or venting to allow cool operation. If possible, mounting the amp in
the passenger compartment will allow cooler operation.
Remember that the controls on top of the amp will need to be accessible for
adjustment later. Keep this in mind as you choose your amplifier’s mounting
location.
Now that you are ready to mount your amplifier, use the supplied 3mm allen
wrench to remove the amplifier shroud. This will give you access to the mount-
ing holes in the amplifier and all wiring connections.
3
Wiring Instructions
Signal can be input into the amplifier using either the low level RCA input con-
nections or the high level (speaker level) connections. Using the low level RCA
connections is the preferred method. Use the high level inputs only if your head
unit does not have low level RCA type outputs.
The use of twisted pair interconnects is recommended for all installations to
minimize noise. When routing these cables through the automobile, try to keep
them away from factory wiring harnesses and other power wiring. If you need to
cross any of this wiring do so at a 90 degree angle to reduce the potential of
noise problems.
When working with power connections it is always recommended that you dis-
connect the battery to prevent accidents.
The ground should be connected to the amplifier first before making any of
the other connections. This wire should be as short as possible (24 inches or less)
and connected to a paint/corrosion free solid metal area of the car’s chassis. Use
the same gauge wire as recommended for the amplifiers power connection to
the battery. Adding an additional ground wire between the car battery’s negative
post and the car chassis of this same gauge (or larger) is also recommended.
If you ever need to remove the amp from the vehicle after it has been
installed, the ground wire should be the last wire disconnected from the amplifi-
er, just the opposite as when you installed it.
A fuse must be installed within 18 inches of the battery to protect the power
wire feeding your amplifier. This fuse should be of at least the same value used
in the amplifier but no higher than the capacity of the wire. See the chart below
for wire size and fusing recommendations.
Model Fuse Size Wire Size
KX-300.4 40A 8 GA
KX-600.4 80A 4 GA
KX-800.4 120A 2 GA
L R L R
Amp 1 Amp 2
L+ L - R + R - L+ L - R + R -
SOURCE UNIT
BRIDGE BRIDGE
LEFT +
LEFT -
RIGHT -
RIGHT +
LEFT +
LEFT -
RIGHT -
RIGHT +
Amp 2
A MP 1
Amp 1 Amp 2
+ - - + + - - + WARNING-Use Only
High Or Low Level
NOT...Both!!!
OFF
HI
PAS S
LO PASS
OFF
HI PASS
LO PASS
AMP 1 AMP 2
HI-LEVEL INPUT
A
MP 1
AMP 2
REMOT E B ASS


Product specificaties

Merk: Kicker
Categorie: Autoradio
Model: KX600.4

Heb je hulp nodig?

Als je hulp nodig hebt met Kicker KX600.4 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Autoradio Kicker

Handleiding Autoradio

Nieuwste handleidingen voor Autoradio