Kicker KX1600.1 Handleiding

Kicker Autoradio KX1600.1

Lees hieronder de šŸ“– handleiding in het Nederlandse voor Kicker KX1600.1 (28 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/28
Ownerā€™s Manual |
Manual del Propietario |
Benutzerhandbuch |
Manuel dā€™utilisation |
KX Amplifiers
2013 KX Mono Amps Rev G.indd 1
2013 KX Mono Amps Rev G.indd 1
2013 KX Mono Amps Rev G.indd 1
2013 KX Mono Amps Rev G.indd 12013 KX Mono Amps Rev G.indd 1 11/13/2012 2:13:57 PM
11/13/2012 2:13:57 PM
11/13/2012 2:13:57 PM
11/13/2012 2:13:57 PM11/13/2012 2:13:57 PM
2
KX.1-SERIES AMPLIFIERS
OWNERā€™S MANUAL
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER ampliļ¬ er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4ā€ (10cm) of open
ventilation for the ampliļ¬ er. If possible, mount the ampliļ¬ er in the climate-controlled passenger compartment. Drill
four holes using a 7/64ā€ (3mm) bit and use the supplied #8 screws to mount the ampliļ¬ er.
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Model Number:
Serial Number:
Model: KX400.1 KX800.1 KX1200.1 KX1600.1 KX2400.1
RMS Power
@ 14.4V, 4 1% THD+NĪ© mono, ļ‚£
@ 14.4V, 2 mono, 1% THD+NĪ©ļ‚£
200W x 1
400W x 1
400W x 1
800W x 1
600W x 1
1200W x 1
800W x 1
1600W x 1
1200W x 1
2400W x 1
Length | in [cm] 8 [20.4] 9 9/16 [24.4] 9 9/16 [24.4] 11 3/16 [28.4] 15 1/2 [39.4]
Speciļ¬ cations common to all models:
Height | in [cm] 2 1/8 [5.5]
Width | in [cm] 8 5/16 [21]
Frequency Response Ā± 1dB 10Hzā€“160Hz
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mVā€“5V
High Level: 250mVā€“10V
Electronic Crossover Variable Lo-pass 40Hzā€“160Hz, 24dB/octave
Bass Boost Parametric 20-80Hz; Variable Q: 1 to 5; Variable Boost, 0-18dB
Subsonic Filter Variable 10ā€“80Hz, 24dB/octave
Remote Bass Yes [included]
Pro Tip: To get the best performance from your new KICKER Ampliļ¬ er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
MODEL: KX400.1 / KX800.1 / KX1200.1 / KX1600.1 / KX2400.1
2013 KX Mono Amps Rev G.indd 2
2013 KX Mono Amps Rev G.indd 2
2013 KX Mono Amps Rev G.indd 2
2013 KX Mono Amps Rev G.indd 22013 KX Mono Amps Rev G.indd 2 11/13/2012 2:17:11 PM
11/13/2012 2:17:11 PM
11/13/2012 2:17:11 PM
11/13/2012 2:17:11 PM11/13/2012 2:17:11 PM
3
Wiring: Disconnect the vehicleā€™s battery to avoid an electrical short. Then, connect the ground wire to the
ampliļ¬ er. Make the ground wire short, 24ā€ (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicleā€™s chassis. Adding an additional ground wire of this same gauge (or larger) between the
batteryā€™s negative post and the vehicle chassis is recommended.
The KX ampliļ¬ er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereoā€™s source unit. A high-level signal can be run from the source unitā€™s speaker outputs to the
stereo RCA input on the end panel of the ampliļ¬ er using the KICKER ZISL as shown (make sure you set the KX
ampliļ¬ erā€™s input level switch to ā€œHIā€). Alternatively, the signal can be delivered to the ampliļ¬ er using the low-level
RCA outputs on the source unit. Set the input level switch on the end panel of the ampliļ¬ er to ā€œLOā€. Either input
method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to
another ampliļ¬ er or component. Keep the audio signal cable away from factory wiring harnesses and other
power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to ampliļ¬ er
shield
+
+
+
ā€“ā€“
ā€“
core conductor KICKER ZISL (optional)
source unit high-level
speaker outputs
OR to ampliļ¬ er
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
KX400.1 1 x 60 Ampere 4 Gauge PK4, CK44, ZCK44
KX800.1 1 x 100 Ampere 4 Gauge PK4, CK44, ZCK44
KX1200.1 1 x 150 Ampere 1/0 Gauge PKD1, PWB050
KX1600.1 1 x 150 Ampere 1/0 Gauge PKD1, PWB050
KX2400.1 1 x 200 Ampere 1/0 Gauge PKD1, PWB050
Install a fuse within 18ā€ (45cm) of the battery and in-line with the power cable connected to your ampliļ¬ er. If you
ever need to remove the ampliļ¬ er from the vehicle after it has been installed, the ground wire should be the last
wire disconnected from the ampliļ¬ er--just the opposite as when you installed it.
2013 KX Mono Amps Rev G.indd 3
2013 KX Mono Amps Rev G.indd 3
2013 KX Mono Amps Rev G.indd 3
2013 KX Mono Amps Rev G.indd 32013 KX Mono Amps Rev G.indd 3 11/13/2012 2:17:12 PM
11/13/2012 2:17:12 PM
11/13/2012 2:17:12 PM
11/13/2012 2:17:12 PM11/13/2012 2:17:12 PM


Product specificaties

Merk: Kicker
Categorie: Autoradio
Model: KX1600.1

Heb je hulp nodig?

Als je hulp nodig hebt met Kicker KX1600.1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Autoradio Kicker

Handleiding Autoradio

Nieuwste handleidingen voor Autoradio