Kicker KMA600.4 Handleiding

Kicker Receiver KMA600.4

Lees hieronder de 📖 handleiding in het Nederlandse voor Kicker KMA600.4 (13 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/13
KMA150.2
KMA360.4
KMA600.4
KMA600.6
Manual del Propietario | Español
AMPLIFICADOR DEL LA SERIE KMA
Benutzerhandbuch | Deutsch
MONOVERSTÄRKER DER KMA-SERIE
Manuel d’utilisation | Française
AMPLIFICATEUR DE SÉRIE KMA
KMA
AMPLIFIERS
Owner’s Manual
2
KMA MULTI-CHANNEL SERIES AMPLIFIERS
OWNER’S MANUAL
INSTALLATION
Mounting: Choose a dry, structurally sound location to mount your KICKER ampli er. Make sure there
are no items behind the area where the screws will be driven. Choose a location that allows at least 4”
(10cm) of open ventilation for the ampli er. Drill four holes using a 7/64” (3mm) bit and use the supplied
#8 screws to mount the ampli er.
Wiring: The KMA ampli ers RCA inputs will receive either high or low level signals from your car stereo’s
source unit. A high-level signal can be run from the source units speaker outputs to the stereo RCA input
on the end panel of the ampli er using the KICKER KISL as shown (see page 3). Alternatively, the signal
can be delivered to the ampli er using the low-level RCA outputs on the source unit. Keep the audio
signal cable away from factory wiring harnesses and other power wiring. If you need to cross this wiring,
cross it at a 90 degree angle.
PERFORMANCE
MODEL: KMA150.2 | KMA360.4 | KMA600.4 | KMA600.6
IMPORTANT SAFETY WARNING
PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER, SPEAKER, OR SUBWOOFER IN
A DISTORTED, CLIPPED OR OVER-POWERED MANNER CAN CAUSE YOUR AUDIO SYSTEM
TO OVERHEAT, POSSIBLY CATCHING FIRE AND RESULTING IN SERIOUS DAMAGE TO YOUR
COMPONENTS AND/OR VEHICLE. AMPLIFIERS REQUIRE UP TO 4 INCHES (10CM) OPEN
VENTILATION. SUBWOOFERS SHOULD BE MOUNTED WITH AT LEAST 1 INCH (2.5CM) CLEARANCE
BETWEEN THE FRONT OF THE SPEAKER AND ANY SURFACE.
Model: KMA150.2 KMA360.4 KMA600.4 KMA600.6
RMS Power
@ 14.4V, 4Ω stereo, ≤ 1% THD+N
@ 14.4V, 2Ω stereo, ≤ 1% THD+N
@ 14.4V, 4Ω bridged mono, ≤ 1% THD+N
40 x 2
75 x 2
150 x 1
65 x 4
90 x 4
180 x 2
75 x 4
150x 4
300 x 2
50 x 6
100 x 6
200 x 3
Length [in, cm] 8-1/16, 20.4 12-7/16, 31.5 12-7/16, 31.5 13-15/16, 35.3
Height [in, cm] 2-5/16, 5.9 2-5/16, 5.9 2-5/16, 5.9 2-5/16, 5.9
Width [in, cm] 6-11/16, 17 6-11/16, 17 6-11/16, 17 6-11/16, 17
Specifi cations common to all models:
Frequency Response ± 1dB 10Hz-20kHz
Signal-to-noise Ratio [dB]
1W Signal-to-noise Ratio [dB]
>95dB, A-weighted, re: rated power
-75dB
Input Sensitivity Low: 125mV-5V, High: 250mV-10V
Electronic Crossover Off, Variable HP & LP 50–200Hz, 12dB/octave slope150.2, 360.4, & 600.4:
600.6: Amps 1 & 2 - Variable HP 0–200Hz, 12dB/octave slope;
Amp 3 - Off, Variable HP & LP 50–200Hz. 12dB/octave slope
Subsonic lter xed @ 25Hz in LP mode
KickEQBass Boost 0–6dB @ 40Hz (600.6 AMP 3 only)
3
Install a fuse within 7(18cm) of the battery and in-line with the power cable connected to your ampli er.
source unit
high-level speaker
outputs
to amplifi er
shield
+
core conductor KICKER KISL (optional)
from source unit high-
level speaker outputs
OR
to amplifi er
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
KMA150.2 1 x 40 Ampere 8 Gauge KMPK8, PK8, CK8
KMA360.4 1 x 60 Ampere 8 Gauge KMPK8, PK8, CK8
KMA600.4 1 x 80 Ampere 4 Gauge KMPK4, PK4, CK4
KMA600.6 1 x 80 Ampere 4 Gauge KMPK4, PK4, CK4
12V
battery
external fuse
remote turn-on (see page 6)
POWER WIRING
ABYC-compliant power terminals
Ampli er uses 304-stainless steel
screws and conformal coated PCB
for increased weather resistance
aluminum bottom
plate
≤7
(18cm)


Product specificaties

Merk: Kicker
Categorie: Receiver
Model: KMA600.4

Heb je hulp nodig?

Als je hulp nodig hebt met Kicker KMA600.4 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Kicker

Handleiding Receiver

Nieuwste handleidingen voor Receiver