Kicker KMA600.1 Handleiding

Kicker Receiver KMA600.1

Lees hieronder de 📖 handleiding in het Nederlandse voor Kicker KMA600.1 (11 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/11
KMA600.1
Manual del Propietario | Español
AMPLIFICADOR DEL LA SERIE KMA.1
Benutzerhandbuch | Deutsch
MONOVERSTÄRKER DER KMA.1-SERIE
Manuel d’utilisation | Française
AMPLIFICATEUR DE SÉRIE KMA.1
KMA
AMPLIFIERS
Owner’s Manual
2
KMA.1-SERIES AMPLIFIERS
OWNER’S MANUAL
INSTALLATION
Mounting: Choose a dry, structurally sound location to mount your KICKER amplifi er. Make sure there
are no items behind the area where the screws will be driven. Choose a location that allows at least 4”
(10cm) of open ventilation for the ampli er. Drill four holes using a 7/64 (3mm) bit and use the supplied
#8 screws to mount the ampli er.
Wiring: The KMA ampli ers RCA inputs will receive either high or low level signals from your source
unit. A high-level signal can be run from the source unit’s speaker outputs to the stereo RCA input on the
end panel of the ampli er using the KICKER KISL as shown (see page 3). Alternatively, the signal can be
delivered to the ampli er using the low-level RCA outputs on the source unit. Keep the audio signal cable
away from factory wiring harnesses and other power wiring. If you need to cross this wiring, cross it at a
90 degree angle.
PERFORMANCE
MODEL: KMA600.1
IMPORTANT SAFETY WARNING
PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER, SPEAKER, OR SUBWOOFER IN A DISTORTED, CLIPPED
OR OVER-POWERED MANNER CAN CAUSE YOUR AUDIO SYSTEM TO OVERHEAT, POSSIBLY CATCHING FIRE
AND RESULTING IN SERIOUS DAMAGE TO YOUR COMPONENTS AND/OR VEHICLE. AMPLIFIERS REQUIRE UP TO
4 INCHES (10CM) OPEN VENTILATION. SUBWOOFERS SHOULD BE MOUNTED WITH AT LEAST 1 INCH (2.5CM)
CLEARANCE BETWEEN THE FRONT OF THE SPEAKER AND ANY SURFACE.
Model: KMA600.1
RMS Power
@ 14.4V, 4Ω mono, 1% THD+N
@ 14.4V, 2Ω mono, 1% THD+N
300W x 1
600W x 1
Length [in, cm] 8-1/16, 20.5
Height [in, cm] 2-5/16, 5.9
Width [in, cm] 7-1/8, 18
Frequency Response ± 1dB 25Hz-200Hz
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mV–5V
High Level: 250mV10V
Electronic Crossover Variable Lo-pass 50Hz–200Hz, 12dB/octave
KickEQ™ Bass Boost 0-12dB @ 40Hz
Subsonic Filter 25Hz, 24dB/octave
Remote Bass Yes
3
Install a fuse within 7 (18cm) of the battery and in-line with the power cable connected to your ampli er.
source unit
high-level speaker
outputs
to ampli er
shield
+
core conductor KICKER KISL (optional)
from source unit high-
level speaker outputs
OR
to ampli er
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
KMA600.1 1 x 80 Ampere 4 Gauge PK4, CK4
12V
battery
external fuse
remote turn-on (see page 5)
woofer
MONO OPERATION
minimum impedance of 2 ohms
ABYC-compliant power terminals
Ampli er uses 304-stainless steel
screws and conformal coated PCB
for increased weather resistance.
aluminum bottom
plate
≤7”
(18cm)


Product specificaties

Merk: Kicker
Categorie: Receiver
Model: KMA600.1

Heb je hulp nodig?

Als je hulp nodig hebt met Kicker KMA600.1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Kicker

Handleiding Receiver

Nieuwste handleidingen voor Receiver