Kicker IX500.4 Handleiding

Kicker Autoradio IX500.4

Lees hieronder de šŸ“– handleiding in het Nederlandse voor Kicker IX500.4 (28 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 63 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/28
IX AMPLIFIER
IX500.4
English Version
VersiĆ³n EspaƱol
Amplificador del la Serie IX.4
Deutsche Version
StereoverstƤrker der IX.4-Serie
Version Francaise
Amplificateur de sƩrie IX.4
LIVINā€™ LOUD
2IX AMPLIFIERS
IX.1-SERIES AMPLIFIERS Ownerā€™s Manual
IX500.4
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER ampliļ¬ er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4ā€ (10cm) of open
ventilation for the ampliļ¬ er. If possible, mount the ampliļ¬ er in the climate-controlled passenger compartment.
Drill four holes using a 7/64ā€ (3mm) bit and use the supplied #8 screws to mount the ampliļ¬ er. Use the IXSM
mounting bracket (sold separately) to stack IX ampliļ¬ ers of different sizes.
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Serial Number:
Model: IX500.4
RMS Power
@ 14.4V, 4 stereo, 1% THD+NĪ©ļ‚£
@ 14.4V, 2 stereo, 1% THD+NĪ©ļ‚£
@ 14.4V, 4 mono, 1% THD+NĪ©ļ‚£
75W x 4
125W x 4
250W x 2
Length 11-3/8ā€ (288mm)
Height 2-3/16ā€ (55mm)
Width 7-7/8ā€ (200mm)
Frequency Response Ā± 1dB 20Hzā€“20kHz
Signal-to-noise Ratio 98dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mVā€“5V
High Level: 250mVā€“10V
Electronic Crossover Selectable HI/LO/OFF, Variable lo-pass 50ā€“200Hz,
12dB/octave
Bass Boost Variable 0ā€“18dB @ 40Hz
Maximum Efļ¬ ciency (2Ī©) >80%
Pro Tip: To get the best performance from your new KICKER Ampliļ¬ er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
IXSM
sold separately
3
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
IX500.4 2 x 50 Ampere 4 Gauge PK4, CK4, ZCK4
Wiring: Disconnect the vehicleā€™s battery to avoid an electrical short. Then, connect the ground wire to the
ampliļ¬ er. Make the ground wire short, 24ā€ (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicleā€™s chassis. Adding an additional ground wire of this same gauge (or larger) between the
batteryā€™s negative post and the vehicle chassis is recommended.
The IX ampliļ¬ er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereoā€™s source unit. Ideally, when connecting the source unit to the ampliļ¬ er, the IX ampliļ¬ erā€™s input
level switch should be set to ā€œLOā€ and a low-level signal should run from the source unitā€™s stereo RCA output to
the stereo RCA input on the end panel of the ampliļ¬ er using RCA interconnect cable. If a low-level stereo RCA
output is not available on the source unit, the signal can be delivered to the ampliļ¬ er using the high-level speaker
outputs on the source unit. Set the input level switch on the end panel of the ampliļ¬ er to ā€œHIā€. Crimp and solder
RCA connectors to the end of the speaker wire running from the high-level speaker outputs on the source unit
and connect the wire to the RCA Inputs on the end panel of the ampliļ¬ er or simplify the installation by using a
KICKER ZISL as shown below. Either input method will provide a low-level output signal at the RCA output, which
effectively passes the audio signal to another ampliļ¬ er or component. Keep the audio signal cable away from
factory wiring harnesses and other power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to ampliļ¬ er
shield
+
ā€“
core conductor
Install a fuse within 18ā€ (45cm) of the battery and in-line with the power cable connected to your ampliļ¬ er. Install
a second fuse within 18ā€ (45cm) of the ampliļ¬ er. If you ever need to remove the ampliļ¬ er from the vehicle after it
has been installed, the ground wire should be the last wire disconnected from the ampliļ¬ er--just the opposite as
when you installed it.
KICKER ZISL
source unit high-level
speaker outputs
OR to ampliļ¬ er
INPUT
LEVEL
LO
HI
AMP2AMP1
L
R
OUTPUT
POWERAMP1
GNDL+ Lā€“ R+ Rā€“ REM +12V
AUTO
TURN ON
12V DC AUDIO
OFFSET
FADER
OFF
ON
BRIDGED
AMP2
L+ Lā€“ R+ Rā€“
BRIDGED
12V
ļ‚£18ā€
(45cm)
battery
external fuse
external fuse
remote turn-on
(see page 5)
bare-metal
chassis ground
ļ‚£24ā€
(60cm)


Product specificaties

Merk: Kicker
Categorie: Autoradio
Model: IX500.4

Heb je hulp nodig?

Als je hulp nodig hebt met Kicker IX500.4 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Autoradio Kicker

Handleiding Autoradio

Nieuwste handleidingen voor Autoradio