Kicker DX500.1 Handleiding

Kicker Autoradio DX500.1

Lees hieronder de šŸ“– handleiding in het Nederlandse voor Kicker DX500.1 (38 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 11 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/38
DX AMPLIFIER
D
LIVINā€™ LOUD
2011 DX Mono Amps RevI.indd 1
2011 DX Mono Amps RevI.indd 1
2011 DX Mono Amps RevI.indd 1
2011 DX Mono Amps RevI.indd 12011 DX Mono Amps RevI.indd 1 11/3/2010 1:29:20 PM
11/3/2010 1:29:20 PM
11/3/2010 1:29:20 PM
11/3/2010 1:29:20 PM11/3/2010 1:29:20 PM
2
DX.1-SERIES AMPLIFIERS
OWNERā€™S MANUAL
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER ampliļ¬ er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4ā€ (10cm) of open
ventilation for the ampliļ¬ er. If possible, mount the ampliļ¬ er in the climate-controlled passenger compartment. Drill
four holes using a 7/64ā€ (3mm) bit and use the supplied #8 screws to mount the ampliļ¬ er.
Wiring: Disconnect the vehicleā€™s battery to avoid an electrical short. Then, connect the ground wire to the
ampliļ¬ er. Make the ground wire short, 24ā€ (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicleā€™s chassis. Adding an additional ground wire of this same gauge (or larger) between the
batteryā€™s negative post and the vehicle chassis is recommended.
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Model Number:
Serial Number:
Model: DX250.1 DX500.1 DX1000.1
RMS Power
@ 14.4V, 4 1% THD+NĪ© mono, ļ‚£
@ 14.4V, 2 mono, 1% THD+NĪ©ļ‚£
140 x 1
250 x 1
275W x 1
500W x 1
550W x 1
1000W x 1
Length, in. (cm) 10-1/4ā€ (26) 10-1/4ā€ (26) 10-1/4ā€ (26)
Electronic Crossover Fixed, 80Hz
24dB/octave
Variable lo-pass 50Hzā€“200Hz
18dB/octave
Subsonic Filter Fixed, 25Hz
24dB/octave
Variable hi-pass 10Hz-30Hz
18dB/octave
Bass Boost Selectable, 0/9dB
@ 40Hz
Variable 0ā€“12dB @ 40Hz
Speciļ¬ cations common to all models:
Height, in. (mm) 2-1/4ā€ (57)
Width, in. (mm) 8-5/16ā€ (211)
Frequency Response Ā± 1dB 20Hzā€“200Hz
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mVā€“5V
High Level: 250mVā€“10V
Remote Bass Yes (not included) Yes Yes
Pro Tip: To get the best performance from your new KICKER Ampliļ¬ er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
MODEL: DX250.1 / DX500.1 / DX1000.1
2011 DX Mono Amps RevI.indd 2
2011 DX Mono Amps RevI.indd 2
2011 DX Mono Amps RevI.indd 2
2011 DX Mono Amps RevI.indd 22011 DX Mono Amps RevI.indd 2 11/3/2010 1:29:25 PM
11/3/2010 1:29:25 PM
11/3/2010 1:29:25 PM
11/3/2010 1:29:25 PM11/3/2010 1:29:25 PM
3
12V
DX250.1
15A 15A
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
DX250.1 1 x 40 Ampere 8 Gauge PK8, ZCK84
DX500.1 1 x 80 Ampere 4 Gauge PK4, CK44, ZCK44
DX1000.1 1 x 100 Ampere 4 Gauge PK4, CK44, ZCK44
The DX ampliļ¬ er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereoā€™s source unit. A high-level signal can be run from the source unitā€™s speaker outputs to the
stereo RCA input on the end panel of the ampliļ¬ er using the KICKER ZISL as shown (make sure you set the DX
ampliļ¬ erā€™s input level switch to ā€œHIā€). Alternatively, the signal can be delivered to the ampliļ¬ er using the low-level
RCA outputs on the source unit. Set the input level switch on the end panel of the ampliļ¬ er to ā€œLOā€. Either input
method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to
another ampliļ¬ er or component. Keep the audio signal cable away from factory wiring harnesses and other
power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to ampliļ¬ er
shield
+
ā€“
core conductor
battery
external fuse
remote turn-on
(see page 5)
bare-metal
chassis ground
ļ‚£18ā€
(45cm)
ļ‚£24ā€
(60cm)
Install a fuse within 18ā€ (45cm) of the battery and in-line with the power cable connected to your ampliļ¬ er. If you
ever need to remove the ampliļ¬ er from the vehicle after it has been installed, the ground wire should be the last
wire disconnected from the ampliļ¬ er--just the opposite as when you installed it.
KICKER ZISL
source unit high-level
speaker outputs
OR to ampliļ¬ er
woofer
MONO OPERATION
minimum impedance of 2 ohms
2011 DX Mono Amps RevI.indd 3
2011 DX Mono Amps RevI.indd 3
2011 DX Mono Amps RevI.indd 3
2011 DX Mono Amps RevI.indd 32011 DX Mono Amps RevI.indd 3 11/3/2010 1:29:26 PM
11/3/2010 1:29:26 PM
11/3/2010 1:29:26 PM
11/3/2010 1:29:26 PM11/3/2010 1:29:26 PM


Product specificaties

Merk: Kicker
Categorie: Autoradio
Model: DX500.1

Heb je hulp nodig?

Als je hulp nodig hebt met Kicker DX500.1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Autoradio Kicker

Handleiding Autoradio

Nieuwste handleidingen voor Autoradio