Kicker DX100.2 Handleiding
Lees hieronder de š handleiding in het Nederlandse voor Kicker DX100.2 (10 pagina's) in de categorie Autoradio. Deze handleiding was nuttig voor 55 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/10
Ā©2007 Stillwater Designs
DX
STEREOAMPLIFIER
DX DX100 ,.2 300.2
English Version
VersiĆ³n EspaƱol
Ampliļ¬ cador del la Serie DX.2
Manual del Propietario
Deutsche Version
StereoverstƤrker der DX.2-Serie
Benutzerhandbuch
Version FranƧaise
Ampliļ¬ cateur de sĆ©rie DX.2
Manuel dāutilisation
2008 DX 100-2 300-2 4in1 a01.indd 1-2
2008 DX 100-2 300-2 4in1 a01.indd 1-2
2008 DX 100-2 300-2 4in1 a01.indd 1-2
2008 DX 100-2 300-2 4in1 a01.indd 1-22008 DX 100-2 300-2 4in1 a01.indd 1-2 1/17/2008 11:19:34 AM
1/17/2008 11:19:34 AM
1/17/2008 11:19:34 AM
1/17/2008 11:19:34 AM1/17/2008 11:19:34 AM
24"
(60cm)
KUNEK
10 - COMA
+12V
18"
(45cm)
XOVER
XOVER
XOVER
Installation
1. Mounting Choose a structurally sound location to mount your Kicker ampliļ¬ er. The controls on the
top of the ampliļ¬ er need to be accessible for adjustment. Make sure there are no items behind the area
where the screws will be driven. Choose a location that allows at least 4ā (10cm) of open ventilation for
the ampliļ¬ er. If possible, mount the ampliļ¬ er in the climate-controlled passenger compartment. Drill four
holes using a 7/64ā (3mm) bit and use the supplied #8 screws to mount the ampliļ¬ er.
2. Wiring Disconnect the vehicleās battery to avoid an electrical short. Then, connect the ground wire to
the ampliļ¬ er. Make the ground wire short, 24ā (60cm) or less, and connect it to a paint and corrosion free
solid metal area of the vehicle's chassis. Adding an additional ground wire of this same gauge (or larger)
between the battery's negative post and the vehicle chassis is recommended.
The DX ampliļ¬ er has dual input sensitivity differential RCA inputs which will receive either high or low
level signals from your car stereoās source unit. Ideally, when connecting the source unit to the ampliļ¬ er,
the DX ampliļ¬ erās input level switch should be set to āLOā and a low-level signal should run from the
source unitās stereo RCA output to the stereo RCA input on the end panel of the ampliļ¬ er using RCA
interconnect cable. If a low-level stereo RCA output is not available on the source unit, the signal can
be delivered to the ampliļ¬ er using the high-level speaker outputs on the source unit. Set the input level
switch on the end panel of the ampliļ¬ er to āHIā. Crimp and solder RCA connectors to the end of the
speaker wire running from the high-level speaker outputs on the source unit and connect the wire to the
RCA Inputs on the end panel of the ampliļ¬ er as shown in Figure 1. Keep the audio signal cable away
from factory wiring harnesses and
other power wiring. If you need to
cross this wiring, cross it at a 90
degree angle.
Install a fuse within 18ā (45cm) of the battery and in-line with the power cable connected to your
ampliļ¬ er. If you ever need to remove the ampliļ¬ er from the vehicle after it has been installed, the ground
wire should be the last wire disconnected from the ampliļ¬ er--just the opposite as when you installed it.
See the chart below for power and ground wire size, and fusing recommendations.
3. Conļ¬ guration The following diagrams show the most common conļ¬ gurations for your Kicker DX
series ampliļ¬ er.
Two Channel Operation (Stereo) DX.2 ampliļ¬ ers are capable of operating into a minimum impedance
of 2 ohms per channel in stereo operation. See Figure 2.
Bridged Operation (Mono) DX.2 series ampliļ¬ ers are capable of operating into a minimum impedance
of 4 ohms when in bridged operation. See Figure 3.
Stereo and Mono Operation Simultaneously (SAMS) The DX.2 series ampliļ¬ ers are capable of
operating into a minimum impedance of 4 ohms mono and 2 ohms per channel in stereo simultaneously
with the use of passive crossovers. See Figure 4.
DX.2SeriesAmpliļ¬ er
OwnerāsManual
TwoChannelModels: DX DX100.2 / 300.2
Authorized Kicker Dealer:
Purchase Date:
Ampliļ¬ er Model Number:
Ampliļ¬ er Serial Number:
Congratulations on your
KICKER purchase!
Please record your purchase
information and keep your sales
receipt for validation of warranty.
__________________________
__________________________
__________________________
__________________________
INSTALLATION
Model 1 AMPERE Power 8DX100.2 (ONE) 15 FUSE GroundWire GA
Model 2 AMPERE Power 8DX300.2 (TWO) 20 FUSE GroundWire GA
2DX.2AMPLIFIER
CONFIGURATION
3
24"
(60cm)
KUNEK
10 - COMA
+12V
18"
(45cm)
24"
(60cm)
KUNEK
10 - COMA
+12V
18"
(45cm)
Figure 2
Figure 3
Figure 4
Minimum Impedance of 2 ohms per channel in stereo operation
Minimum impedance of 4 ohms while in bridged operation
Minimum impedance of 4 ohms mono and 2 ohms
per channel in stereo simultaneously Ground
Remote
Turn-On
Fuse
Battery
High Pass
High Pass
Low Pass
Signal In
L+
L-
R+
R-
Source Unit
Ground
Remote
Turn-On
Fuse
Battery
Ground
Remote
Turn-On
Fuse
Battery
L+
L-
R+
R-
L+
L-
R+
R-
Signal In
Signal In
Source Unit
Source Unit
Bridge Wiring
Bridge Wiring
Bridged Operation (Mono)
Two Channel Operation (Stereo)
Stereo and Mono Operation Simultaneously (SAMS)
Note: To get the best performance from your new Kicker Ampliļ¬ er, we recommend using genuine Kicker Accessories and Wiring.
+
+
>
>
>
>>
+
>
>
>
>>
Core Cable
Ground or Shielding
High-level Speaker Output Wire
To Ampliļ¬ er
To Source Unit
Figure 1
2008 DX 100-2 300-2 4in1 a01.indd 3-4
2008 DX 100-2 300-2 4in1 a01.indd 3-4
2008 DX 100-2 300-2 4in1 a01.indd 3-4
2008 DX 100-2 300-2 4in1 a01.indd 3-42008 DX 100-2 300-2 4in1 a01.indd 3-4 1/17/2008 11:19:34 AM
1/17/2008 11:19:34 AM
1/17/2008 11:19:34 AM
1/17/2008 11:19:34 AM1/17/2008 11:19:34 AM
Operation
1. Crossover Switch Use the XOVER switch on the end panel of the ampliļ¬ er to set the internal
crossover to OFF, HI or LO. When the switch is set to OFF, a full bandwidth signal will be ampliļ¬ ed. Set
the switch to HI if you want the ampliļ¬ erās internal crossover to serve as a high-pass ļ¬ lter ļ¬ xed at 100 Hz
with an 18 db/octave slope. Set the switch to LO if you want the ampliļ¬ erās internal crossover to serve as
a low-pass ļ¬ lter ļ¬ xed at 80 Hz with an 18 db/octave slope to power your subwoofers.
2. Input Gain Control The input gain control is not a volume control. It matches the output of the
source unit to the input level of the ampliļ¬ er. Turn the source unit up to about 3/4 volume (if the source
unit goes to 30, turn it to 25). Next, slowly turn (clockwise) the gain on the ampliļ¬ er up until you can hear
audible distortion, then turn it down a little.
3. Bass Boost Turn the bass boost on to increase bass by 9db at 40 Hz. If you choose to enable the
bass boost it may be necessary to reduce the input gain control on the ampliļ¬ er to avoid clipping.
5. Automatic Turn-On Selection The DX series offers three different automatic turn-on modes that can
be selected on the end panel; +12V, DC Offset, and Audio. Using either the DC Offset or Audio mode
causes the REM terminal to have +12V out for turning on additional ampliļ¬ ers
īRemote Turn-On +12V Set the switch to to use the remote turn-on lead from your source unit. Run
18 Ga wire from the Remote Turn-On Lead on your source unit to the terminal labeled REM between the
ampliļ¬ erās positive and negative power terminals. This is the preferred automatic turn-on method.
īDC Offset Turn-On If Remote Turn-On is not an option, the next best setting is . The DC DC Offset
Offset mode detects a 6 volt surge from the HI Level speaker outputs when the source unit has been
turned on.
īSignal Sense Turn-On Audio The setting is the ļ¬ nal alternative for Automatic turn-on. This is a Signal
Sense turn-on method that detects the incoming audio signal from your source unit and automatically
turns on the amp. This turn-on method will not work properly if the input gain control is not set
appropriately.
TroubleShooting
If your ampliļ¬ er does not appear to be working, check the obvious things ļ¬ rst such as blown fuses, poor
or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There is
a Power Protection LED on the side power panel of your Kicker DX series ampliļ¬ er. Depending on the
state of the ampliļ¬ er and the vehicleās charging system, the LED will glow either Red, Yellow or Green.
When the green LED is lit this indicates the ampliļ¬ er is turned on and no trouble exists.
īGreen LED off, no output? With a Volt Ohm Meter (VOM) check the following: 1) +12 volt power
terminal (should read +12V to +16V) 2) Remote turn-on terminal (should read +12V to +16V) 3) Check
for reversed power and ground connections. 4) Ground terminal, for proper conductivity. 5) Check for
blown fuses
īGreen LED on, no output? Check the following: 1) RCA connections 2) Test speaker outputs with
a āknownā good speaker. 3) Substitute source unit with a āknownā good source unit. 4) Check for a
signal in the RCA cable feeding the ampliļ¬ er with the VOM meter set to measure āACā voltage.
īYellow LED ļ¬ ashing with loud music? The yellow LED indicates low battery voltage. Check all the
connections in your vehicleās charging system. It may be necessary to replace or charge your vehicleās
battery or replace your vehicleās alternator.
īRed LED on, no output? 1) Ampliļ¬ er is very hot. Thermal protection is engaged. Test for proper ī
impedance at the speaker terminals with a VOM meter (see the diagrams in this manual for minimum
recommended impedance and multiple speaker wiring suggestions). Also check for adequate airļ¬ ow
around the ampliļ¬ er. 2) Ampliļ¬ er shuts down only while vehicle is running. Voltage protection circuitry ī
is engaged. Voltage to the ampliļ¬ er is not within the 9-16 volt operating range. Have the vehicle's
charging and electrical system inspected. 3) Ampliļ¬ er will only play at low volume levels. Short circuit ī
protection is engaged. Check for speaker wires shorted to each other or to the vehicle chassis. Check
for damaged speakers, or speaker(s) operating below the minimum recommended impedance.
īNo output from one channel? 1) Check the balance control on source unit 2) Check the RCA (or
speaker input) and speaker output connections for the channel 3) Swap the RCA (or speaker input)
OPERATION
DX.2AMPLIFIER
4
cable from left to right. If the problem changes sides then you have a bad RCA (or speaker input) cable
or source unit problem. 4) Swap the speaker output wire from left to right. If the problem changes sides
then you have a bad speaker cable, passive crossover network and/or speaker.
ī Alternator noise-whining sound with engineās RPM? 1) Check for damaged RCA (or speaker input)
cable 2) Check the routing of RCA (or speaker input) cable 3) Check the source unit for proper
grounding 4) Check the gain settings and turn them down if they are set too high.
īPoor stereo image or reduced bass response? Check system phasing by turning the balance ī
control from left to right. If there is more bass output when turned to either side, then check your speaker
wiring, passive crossover networks and speaker terminals for proper positive and negative connections.
Reverse a speaker connection from positive to negative on the stereo/subwoofer channel(s); if the bass
improves, the speaker was out of phase.
Please Note: Modern high performance speakers have a lower DC Resistance than what used to be
available. The Kicker Coaxial and Component speakers are rated at four ohms (some DC Resistances
may be as low as 3 ohms) and work with any ampliļ¬ er designed to operate at a four ohm load. If you
want to use two Kicker Coaxial or Component speakers on a single channel of your ampliļ¬ er wire the
speakers in series. This will improve the sound quality, lower the total harmonic distortion and lessen
the thermal load at the ampliļ¬ er. This may prevent an ampliļ¬ er from shutting down, due to over-current
protection circuitry.
CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are
correct. Improper connections can result in blown ampliļ¬ er fuses as well as the failure of other critical
systems in the vehicle.
If you have more questions about the installation or operation of your new KICKER product, see the
Authorized KICKER Dealer where you made your purchase. For more advice on installation, click on
the SUPPORT tab on the Kicker homepage, www.kicker.com. Choose the TECHNICAL SUPPORT tab,
choose the subject you are interested in, and then download or view the corresponding information.
Please E-mail support@kicker.com or call Technical Services (405) 624-8583 for unanswered or speciļ¬ c
questions.
PERFORMANCE
5
Performance
Model DX DX100.2 300.2
RMS Power in Watts, all channels driven @14.4
Volts, 4 stereo, 1% THD+NĪ© ā¤ 25 x 2 75 x 2
@ 2 stereo, 1% THD+N 50 x 2 150 x 2Ī© ā¤
@ 4 mono, 1% THD+N 100 300 x 1Ī© ā¤
Length: in(cm) 8 3/8 (21.3) 15 (38.1)
Speciļ¬ cations common to all models:
Height: in(mm) 2 1/8 (54mm)
Width: in(mm) 8 5/16 (211mm)
Frequency Response, Ā± 1 db: 20 Hz - 20 kHz
Signal-to-Noise Ratio: >95db, a-weighted, re: rated power
Input Sensitivity: Low Level: 125mV-5V
High Level 250mV-10V
Selectable Electronic Crossover: 18 db/Octave High Pass Fixed @ 100Hz
18 db/Octave Low Pass Fixed @ 80Hz
Bass Boost: 9db Bass Boost Switch Fixed @ 40Hz
Model .2 DX100
25 x 2 @ 4 ohms, 14.4Vdc, 1%THD, CEA-2006 Watts
Signal to Noise Ratio -84
CEA-2006 (ref: 1W, A-weighted)
Model .2 DX300
75 x 2 @ 4 ohms, 14.4Vdc, 1%THD, CEA-2006 Watts
Signal to Noise Ratio -74
CEA-2006 (ref: 1W, A-weighted)
2008 DX 100-2 300-2 4in1 a01.indd 5-6
2008 DX 100-2 300-2 4in1 a01.indd 5-6
2008 DX 100-2 300-2 4in1 a01.indd 5-6
2008 DX 100-2 300-2 4in1 a01.indd 5-62008 DX 100-2 300-2 4in1 a01.indd 5-6 1/17/2008 11:19:35 AM
1/17/2008 11:19:35 AM
1/17/2008 11:19:35 AM
1/17/2008 11:19:35 AM1/17/2008 11:19:35 AM
Product specificaties
| Merk: | Kicker |
| Categorie: | Autoradio |
| Model: | DX100.2 |
Heb je hulp nodig?
Als je hulp nodig hebt met Kicker DX100.2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Autoradio Kicker
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
2 Juni 2023
Handleiding Autoradio
- Autoradio Philips
- Autoradio Sony
- Autoradio Panasonic
- Autoradio LG
- Autoradio AEG
- Autoradio Daewoo
- Autoradio Ford
- Autoradio Fiat
- Autoradio Grundig
- Autoradio JVC
- Autoradio JBL
- Autoradio Kenwood
- Autoradio Medion
- Autoradio Opel
- Autoradio Pioneer
- Autoradio Renault
- Autoradio Volvo
- Autoradio Adcom
- Autoradio Aiwa
- Autoradio Akai
- Autoradio Alpine
- Autoradio Audiosonic
- Autoradio Audiovox
- Autoradio Audison
- Autoradio Auna
- Autoradio Autovision
- Autoradio Axton
- Autoradio Becker
- Autoradio Blaupunkt
- Autoradio Boss
- Autoradio Boston Acoustics
- Autoradio Brigmton
- Autoradio Denver
- Autoradio DLS
- Autoradio Dual
- Autoradio Eclipse
- Autoradio Elta
- Autoradio Eltax
- Autoradio Emphaser
- Autoradio ESX
- Autoradio Focal
- Autoradio Fusion
- Autoradio Ground Zero
- Autoradio Harman Kardon
- Autoradio Hertz
- Autoradio Hifonics
- Autoradio Hyundai
- Autoradio Impulse
- Autoradio Lanzar
- Autoradio Lenco
- Autoradio Mac Audio
- Autoradio Macrom
- Autoradio Maginon
- Autoradio Magnat
- Autoradio Manta
- Autoradio Marquant
- Autoradio MB Quart
- Autoradio Mercedes-Benz
- Autoradio MT Logic
- Autoradio Mtx Audio
- Autoradio Muse
- Autoradio Nedis
- Autoradio Nextbase
- Autoradio Parrot
- Autoradio Phonocar
- Autoradio Pure
- Autoradio Pyle
- Autoradio Renkforce
- Autoradio Revo
- Autoradio Roadstar
- Autoradio Rockford Fosgate
- Autoradio Rodek
- Autoradio RTO
- Autoradio Sanyo
- Autoradio Scott
- Autoradio Sencor
- Autoradio Sevic
- Autoradio Silvercrest
- Autoradio Skoda
- Autoradio Smart
- Autoradio Soundstream
- Autoradio Spectron
- Autoradio Stinger
- Autoradio Tamashi
- Autoradio Technaxx
- Autoradio Telefunken
- Autoradio Telestar
- Autoradio Tevion
- Autoradio Tokai
- Autoradio Toxic
- Autoradio Twister
- Autoradio Ultimate
- Autoradio US Blaster
- Autoradio Varta
- Autoradio VDO
- Autoradio VDO Dayton
- Autoradio Vieta
- Autoradio Voxx
- Autoradio VW
- Autoradio Watssound
- Autoradio Xomax
- Autoradio Zenec
- Autoradio Jensen
- Autoradio OneConcept
- Autoradio Orion
- Autoradio Overmax
- Autoradio Clas Ohlson
- Autoradio McIntosh
- Autoradio Clatronic
- Autoradio ECG
- Autoradio Caliber
- Autoradio KrĆ¼ger And Matz
- Autoradio Naxa
- Autoradio Kunft
- Autoradio Scion
- Autoradio Clarion
- Autoradio Cobra
- Autoradio Conceptronic
- Autoradio Biltema
- Autoradio Majestic
- Autoradio Trevi
- Autoradio Crunch
- Autoradio Multilaser
- Autoradio Sendai
- Autoradio Orava
- Autoradio SPC
- Autoradio Norauto
- Autoradio Lark
- Autoradio Xblitz
- Autoradio Shuttle
- Autoradio Deaf Bonce
- Autoradio Cartronix
- Autoradio Dension
- Autoradio Raveland
- Autoradio RetroSound
- Autoradio Planet Audio
- Autoradio SoundMAX
- Autoradio Mystery
Nieuwste handleidingen voor Autoradio
20 November 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024
15 November 2024
13 November 2024