Kenton Midi USB Host Handleiding

Kenton Niet gecategoriseerd Midi USB Host

Lees hieronder de đź“– handleiding in het Nederlandse voor Kenton Midi USB Host (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 203 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
MIDI USB HOST
MIDI USB HOSTMIDI USB HOST
MIDI USB HOST
MIDI Host for Class Compliant
USB MIDI devices
Operating manual
2
__________________________________________________________________________________
FCC Statement for MIDI USB Host
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
__________________________________________________________________________________
Important
This product will ONLY work with USB devices which are MIDI Class Compliant. Check in the product
manual or contact the manufacturers to establish if the device you intend to attach is Class Compliant.
If you attach a non class compliant device, it just won’t be recognised. No damage will be caused to
either the host or the device.
__________________________________________________________________________________
Description
The MIDI USB Host has a USB Host port (USB A socket), a MIDI IN and a MIDI OUT (both 5 pin DIN).
MIDI data received at the MIDI IN socket will be sent to the USB device. MIDI data received from the
USB device will be sent to the MIDI OUT socket.
The MIDI USB Host is powered by a regulated 5V mains adaptor (supplied), and can supply up to
500mA of buss power to the attached USB device.
Connecting
It is recommended that you attach your USB device to the MIDI USB Host before applying power. Then
plug-in and power the power adaptor. The active LED should be lit up. If you apply power with nothing
plugged into the MIDI USB Host, the Active LED will flash steadily; this is to indicate that it is waiting for
a suitable device to be attached. If it is still flashing when you have attached your device, then it is
possible that your device is not class compliant, however you could try turning off the power and start
again.
Some USB MIDI devices have two modes of operation and can be set to operate in Class Compliant
mode even if this is not the default. The Class Compliant mode might be called “generic driver”, the
other mode may be called something like “advanced driver”. Consult the device manual to see if the
mode can be set for Class Compliant.
If you unplug then re-plug the USB cable while it is powered the device might reconnect, but it is not
certain.
Power
It is essential to use only the supplied 5V regulated power adaptor. Applying a voltage higher than 5V
to the MIDI USB Host will probably not damage the MIDI USB Host itself, but it could damage any
3
attached USB device as the 5V is passed on to the attached USB device for buss power. There is
protection circuitry inside the MIDI USB Host to protect against reverse polarity and over-voltage, but
these should be treated as a last resort and are not guaranteed to prevent damage to an attached USB
device in the event of over-voltage as the USB buss voltage could rise to 6.5V before being clamped.
Care should be taken to ensure that power adaptors for other pieces of equipment are not accidentally
plugged into the MIDI USB Host.
If the input voltage rises above 6.5 volts then power will be shut off. The LED will go out and the unit
will not operate again until power has been removed for at least 60 seconds. This allows time for the
thermal fuse to reset.
Firmware version Request
:
You can send a SysEx message to request the version number of the firmware currently installed in
the unit.
The firmware version request message is - F0 00 20 13 13 60 F7 (hex)
The unit replies with the version number as F0 00 20 13 13 6F xx xx xx xx F7 (hex).
Where xx is a number in ASCII and the leftmost digit is the most significant.
For example - F0 00 20 13 0E 6F 31 32 33 34 F7 (hex) = version number 1234

Product specificaties

Merk: Kenton
Categorie: Niet gecategoriseerd
Model: Midi USB Host

Heb je hulp nodig?

Als je hulp nodig hebt met Kenton Midi USB Host stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Kenton

Kenton

Kenton PRO-DCB Handleiding

4 Juni 2023
Kenton

Kenton MERGE-8 Handleiding

29 Mei 2023
Kenton

Kenton THRU-12 Handleiding

25 Mei 2023
Kenton

Kenton PRO CV to MIDI Handleiding

21 Mei 2023
Kenton

Kenton Midi USB Host Handleiding

19 Mei 2023
Kenton

Kenton MERGE-4 Handleiding

17 Mei 2023
Kenton

Kenton D-Sync Handleiding

16 Mei 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Gourmetmaxx

Gourmetmaxx 03863 Handleiding

24 December 2024
Vello

Vello PGS-P Handleiding

24 December 2024
Venom

Venom Quad Charging Station VS4796 Handleiding

24 December 2024
Nec

Nec IPJ2000CM Handleiding

24 December 2024
Monogram

Monogram ZKPN Handleiding

24 December 2024
Philips

Philips Quick Clean Pot QCP10 Handleiding

24 December 2024
Philips

Philips Senseo HD7002 Handleiding

24 December 2024
D-Link

D-Link DUB-C2 Handleiding

24 December 2024
Nec

Nec MultiPresenter Stick DS1-MP10RX1 Handleiding

24 December 2024
Nec

Nec DS1-TM01 Handleiding

24 December 2024