Kemppi A7 TIG Orbital System 300 Handleiding
Kemppi
Las apparaat
A7 TIG Orbital System 300
Lees hieronder de 📖 handleiding in het Nederlandse voor Kemppi A7 TIG Orbital System 300 (61 pagina's) in de categorie Las apparaat. Deze handleiding was nuttig voor 41 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/61
300
1920390
1615
A7 TIG Orbital System
EN
OPERATING MANUAL
2A7 TIG Orbital System 300© Kemppi Oy 2016 1615
OPERATING MANUAL
CONTENTS
1. Introduction ..........................................................................................4
1.1 General ......................................................................................................4
1.2 About the product ....................................................................................5
1.3 Weld head .................................................................................................. 6
1.3.1 General specications .............................................................................6
1.4 Controller unit ...........................................................................................7
1.4.1 Remote control ......................................................................................7
1.5 Compatibility .............................................................................................8
2. Installation .............................................................................................9
2.1 Controller connections .............................................................................9
2.2 Water cooler ............................................................................................10
2.2.1 Filling water cooler with coolant ............................................................10
2.2.2 Operating the water ow .......................................................................10
2.3 Weld head set-up ....................................................................................11
2.3.1 Assemblies ..........................................................................................11
2.4 Installing guide ring on tube ..................................................................13
2.5 Mounting the weld head ........................................................................14
2.6 Wire spool ................................................................................................15
2.7 Electrode ..................................................................................................16
2.8 Torch centering .......................................................................................17
2.9 Mechanical adjustments .........................................................................17
3. Operation .............................................................................................18
3.1 Welding settings .....................................................................................18
3.1.1 Setting current level ..............................................................................18
3.1.2 Pulsillation (synchronized pulsed current/oscillation mode)..........................18
3.1.3 Filler wire speed ...................................................................................18
3.1.4 Root-pass procedure .............................................................................19
3.1.5 Hot-pass procedure ..............................................................................19
3.1.6 Fill passes, oscillation (weave), and stringer bead techniques ........................20
3.1.7 Shield gas eects ..................................................................................21
3.2 Preparing the work piece ........................................................................21
3.2.1 Groove preparation ...............................................................................21
3.2.2 Joint design and t-up tolerance ............................................................21
3.2.3 Other preparations ...............................................................................22
3.2.4 Developing weld procedures/process parameters ......................................22
3.3 Controller unit menus .............................................................................23
3.3.1 Main Menu ..........................................................................................23
3.3.2 Maintenance Menu ...............................................................................25
3.3.3 Options Menu ......................................................................................27
3.3.4 Compatible weld head models ................................................................28
3.3.5 Calibrate head .....................................................................................28
3.3.6 300-head guide ring speed factors ...........................................................29
3.3.7 Advanced Help ....................................................................................30
3.3.8 Autotack .............................................................................................30
3.3.9 Autoprogram .......................................................................................31
3.4 Alphanumeric labelling ...........................................................................33
3.5 Manual programming .............................................................................33
3.6 Prepurge – Upslope.................................................................................37
3.7 Programmed oscillation width (without striking an arc) .......................37
3.8 Editing a weld program...........................................................................38
3.9 Completing the programming ...............................................................39
3.10 Updating software ..................................................................................39
3.11 Welding ...................................................................................................39
3.12 Travel speed correction ...........................................................................39
3.13 Shielding gas ...........................................................................................40
3.13.1 Purging the pipe ID with inert gas ...........................................................41
4. Additional details ..............................................................................42
4.1 Controller technical data .........................................................................42
4.2 Weld head technical data........................................................................42
4.3 Ordering information ..............................................................................43
3A7 TIG Orbital System 300© Kemppi Oy 2016 1615
OPERATING MANUAL
5. Troubleshooting ................................................................................46
5.1 Operation problems ................................................................................46
5.2 Root-pass renement for horizontal pipe (5G position) ........................47
5.3 Common weld defects: identication and prevention ..........................48
5.4 Warnings/error messages ......................................................................49
5.5 Checking machine setup during booting ..............................................53
5.6 Machine system messages......................................................................54
5.7 Controller unit fault conditions ..............................................................54
6. Maintenance .......................................................................................55
6.1 Preventing tungsten electrode rotation not concentric to tube OD .....55
6.2 Periodic maintenance .............................................................................55
6.3 Weld head maintenance .........................................................................56
6.3.1 External maintenance............................................................................56
6.3.2 Low prole kit installation ......................................................................56
6.3.3 Torch cable replacement ........................................................................56
6.3.4 Maintenance of the wire feed nozzle ........................................................56
6.3.5 Water cooler maintenance/ushing procedure for the torch cable .................57
6.3.6 Maintenance of torch components ..........................................................57
6.3.7 Cleaning the weld head .........................................................................58
6.3.8 Internal arcing .....................................................................................58
6.4 Printer operation and maintenance .......................................................59
6.4.1 Installing paper in the printer..................................................................59
6.4.2 Cleaning the printer ..............................................................................59
6.5 Service Workshop maintenance ............................................................59
7. Disposal ................................................................................................60
Product specificaties
| Merk: | Kemppi |
| Categorie: | Las apparaat |
| Model: | A7 TIG Orbital System 300 |
Heb je hulp nodig?
Als je hulp nodig hebt met Kemppi A7 TIG Orbital System 300 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Las apparaat Kemppi
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
Handleiding Las apparaat
- Las apparaat DEKO
- Las apparaat Elektra Beckum
- Las apparaat Frilass
- Las apparaat Gys
- Las apparaat Kinzo
- Las apparaat Parkside
- Las apparaat Weldkar
Nieuwste handleidingen voor Las apparaat
6 Oktober 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023