Kemppi A7 MIG Power Source 350 Handleiding
Kemppi
Las apparaat
A7 MIG Power Source 350
Lees hieronder de đź“– handleiding in het Nederlandse voor Kemppi A7 MIG Power Source 350 (67 pagina's) in de categorie Las apparaat. Deze handleiding was nuttig voor 40 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/67
350, 450
1920300
1824
A7 MIG WelderA7 MIG Welder
EN
OPERATING MANUAL
2A7 MIG Welder© Kemppi Oy 2018 1824
OPERATING MANUAL
CONTENTS
1. Introduction ..........................................................................................4
2. Installation .............................................................................................5
3. System Overview ................................................................................6
3.1 Power Source ............................................................................................. 6
3.2 Robot interface unit ..................................................................................7
3.3 User interfaces ........................................................................................... 8
3.4 A7 MIG Wire Feeder 25 ..............................................................................9
3.5 MIG Guns .................................................................................................11
3.6 Cooling unit .............................................................................................12
3.7 I/O device.................................................................................................13
4. Using the welder ...............................................................................14
4.1 Basic controls ...........................................................................................14
4.2 Setup panel .............................................................................................14
4.2.1 Button functions ..................................................................................15
4.2.2 Main menu ..........................................................................................16
4.2.3 Memory channel wizard ........................................................................16
4.2.4 User settings ........................................................................................22
4.2.5 Welding system settings ........................................................................22
4.2.6 System tests ........................................................................................25
4.2.7 Robot settings .....................................................................................26
4.3 Web user interface ..................................................................................29
4.3.1 Welding display....................................................................................30
4.3.2 Gas, air and wire inch ............................................................................30
4.3.3 Logbook .............................................................................................31
4.3.4 About .................................................................................................31
4.3.5 Welding settings – Memory channels .......................................................31
4.3.6 Settings – Language .............................................................................35
4.3.7 Settings – Users ....................................................................................35
4.3.8 Settings – Change PIN ...........................................................................35
4.3.9 Settings – Fieldbus................................................................................36
4.3.10 Settings – Network ...............................................................................36
4.3.11 Settings – Backup, restore and reset .........................................................37
4.3.12 Settings – Licenses ................................................................................37
4.4 User identication ...................................................................................38
4.4.1 Overview ............................................................................................38
4.4.2 Turning user identication system on .......................................................39
4.4.3 Creating new users ...............................................................................39
4.4.4 Deleting a user .....................................................................................40
4.4.5 Changing user role ...............................................................................40
4.4.6 Changing username ..............................................................................40
4.4.7 Changing PIN code ...............................................................................40
4.4.8 Resetting PIN code ...............................................................................41
4.4.9 Logging in and out, changing active user ..................................................41
4.5 Touch sensor (seam search) ....................................................................42
4.5.1 Voltage source, levels and safety .............................................................44
4.5.2 Touch tool ...........................................................................................45
4.5.3 Fast status output .................................................................................45
4.5.4 Selecting output voltage .......................................................................45
4.5.5 Conguring touch tool ..........................................................................46
4.6 Through Arc Seam Tracking (TAST) ........................................................46
4.7 Collision sensor .......................................................................................47
4.7.1 Setting collision sensor on and o ...........................................................48
4.7.2 Selecting sensor type ............................................................................48
4.7.3 Selecting output polarity .......................................................................48
4.8 Wire feeder ..............................................................................................49
4.8.1 Loading the ller wire ...........................................................................49
4.9 Arc measurement ....................................................................................53
4.9.1 Setup and calibration ............................................................................53
4.9.2 Display ...............................................................................................53
3A7 MIG Welder© Kemppi Oy 2018 1824
OPERATING MANUAL
4.10 Gas ow sensor .......................................................................................54
4.10.1 On/O control .....................................................................................54
4.10.2 Gas ow sensing level ...........................................................................54
4.10.3 Gas mixture setup ................................................................................55
5. Troubleshooting ................................................................................56
5.1 Typical problems .....................................................................................56
5.2 Error codes ...............................................................................................57
5.2.1 Power source errors ..............................................................................57
5.2.2 Cooling unit errors ................................................................................58
5.2.3 Wire feeder errors .................................................................................59
5.2.4 Welding curve errors .............................................................................59
5.2.5 Robot interface errors............................................................................60
5.2.6 I/O device errors ...................................................................................61
6. Operation disturbances ..................................................................62
7. Maintenance .......................................................................................63
7.1 Daily maintenance ..................................................................................63
7.2 Periodic maintenance .............................................................................63
7.3 Service shop maintenance ......................................................................63
8. Disposal ................................................................................................64
9. Ordering numbers ............................................................................64
10. Technical data ....................................................................................65
Product specificaties
| Merk: | Kemppi |
| Categorie: | Las apparaat |
| Model: | A7 MIG Power Source 350 |
Heb je hulp nodig?
Als je hulp nodig hebt met Kemppi A7 MIG Power Source 350 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Las apparaat Kemppi
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
Handleiding Las apparaat
- Las apparaat DEKO
- Las apparaat Elektra Beckum
- Las apparaat Frilass
- Las apparaat Gys
- Las apparaat Kinzo
- Las apparaat Parkside
- Las apparaat Weldkar
Nieuwste handleidingen voor Las apparaat
6 Oktober 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023