Kemppi A5 TIG Orbital System 75 Handleiding
Kemppi
Las apparaat
A5 TIG Orbital System 75
Lees hieronder de 📖 handleiding in het Nederlandse voor Kemppi A5 TIG Orbital System 75 (33 pagina's) in de categorie Las apparaat. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/33
75
1920370
1615
A5 TIG Orbital System
EN
OPERATING MANUAL
2A5 TIG Orbital System 75© Kemppi Oy 2016 1615
OPERATING MANUAL
CONTENTS
1. Introduction ..........................................................................................3
1.1 General ......................................................................................................3
1.2 About the product ....................................................................................4
1.3 Weld head .................................................................................................. 5
1.3.1 Tube diameters and weld head outline dimensions .......................................5
1.3.2 Collets ..................................................................................................6
1.3.3 Collet frame and collets ...........................................................................6
1.3.4 Flush collets ..........................................................................................7
1.3.5 Extended collets / combination .................................................................7
1.4 Controller unit ...........................................................................................8
1.5 TIG power source.......................................................................................8
1.6 Tube preparation ......................................................................................8
2. Installation .............................................................................................9
2.1 Connecting the weld head .......................................................................9
2.2 Installing collets on the weld head .........................................................10
2.3 Mounting the weld head ........................................................................10
3. Operation .............................................................................................11
3.1 Rotor gear ................................................................................................11
3.2 Tungsten electrode .................................................................................11
3.2.1 Tungsten electrode diameter and length ..................................................11
3.2.2 Installing the tungsten electrode and holder .............................................12
3.2.3 Tungsten electrode geometry guidelines ..................................................12
3.3 Electrode sharpeners ..............................................................................13
3.4 Weld head control panel .........................................................................14
3.5 Controller unit control panel .................................................................14
3.5.1 Quick guide to start welding ...................................................................14
3.5.2 Main/Home screen ...............................................................................15
3.5.3 Initial setup screen ................................................................................15
3.5.4 Program storage (Library) ......................................................................15
3.5.5 Weld Programs – selecting a weld program 1–10 ........................................16
3.5.6 Calibrating weld head or power source output ...........................................16
3.5.7 Calibrating weld power source current output ...........................................17
3.5.8 Selecting power source .........................................................................18
3.5.9 Pulsed/non-pulsed welding ....................................................................18
3.5.10 Gas purge ...........................................................................................19
3.5.11 Preparing welding – test weld .................................................................20
3.5.12 Icons and screens during welding ...........................................................21
3.6 Equipment stop ......................................................................................22
3.7 Updating software ..................................................................................22
4. Additional details ..............................................................................23
4.1 Technical data ..........................................................................................23
4.2 Ordering information ..............................................................................23
4.2.1 Ordering collets ...................................................................................24
4.2.2 Collets ................................................................................................24
4.2.3 Tungsten electrode material and ordering information ................................26
5. Troubleshooting ................................................................................29
5.1 Operation problems ................................................................................29
5.2 Warnings and error messages ................................................................30
5.3 Common weld defects ............................................................................31
6. Maintenance .......................................................................................31
6.1 Daily maintenance ..................................................................................31
6.2 Periodic maintenance .............................................................................31
6.3 Service Workshop maintenance ............................................................32
7. Disposal ................................................................................................32
3A5 TIG Orbital System 75© Kemppi Oy 2016 1615
OPERATING MANUAL
1. INTRODUCTION
1.1 General
Congratulations on choosing A5 TIG Orbital System 75
welding equipment. Used correctly, Kemppi products can
signicantly increase the productivity of your welding and
provide years of economical service.
This operating manual contains important information on
the use, maintenance and safety of your Kemppi product.
The technical specications of the equipment can be
found at the end of the manual.
Please read the operating manual and the safety
instructions booklet carefully before using the equipment
for the rst time. For your own safety and that of your
working environment, pay particular attention to the
safety instructions in the manual.
For more information on Kemppi products, contact
Kemppi Oy, consult an authorized Kemppi dealer, or visit
the Kemppi website at www.kemppi.com.
The specications presented in this manual are subject to
change without prior notice.
Important notes
Items in the manual that require particular attention in
order to minimise damage and harm are indicated with
below symbols. Read these sections carefully and follow
their instructions.
Note: Gives the user a useful piece of information.
Caution: Describes a situation that may result in
damage to the equipment or system.
Warning: Describes a potentially dangerous situation.
If not avoided, it will result in personal damage or fatal
injury.
Disclaimer
While every eort has been made to ensure that the
information contained in this guide is accurate and
complete, no liability can be accepted for any errors
or omissions. Kemppi reserves the right to change the
specication of the product described at any time without
prior notice. Do not copy, record, reproduce or transmit
the contents of this guide without prior permission from
Kemppi.
Product specificaties
| Merk: | Kemppi |
| Categorie: | Las apparaat |
| Model: | A5 TIG Orbital System 75 |
Heb je hulp nodig?
Als je hulp nodig hebt met Kemppi A5 TIG Orbital System 75 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Las apparaat Kemppi
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
30 Oktober 2022
Handleiding Las apparaat
- Las apparaat DEKO
- Las apparaat Elektra Beckum
- Las apparaat Frilass
- Las apparaat Gys
- Las apparaat Kinzo
- Las apparaat Parkside
- Las apparaat Weldkar
Nieuwste handleidingen voor Las apparaat
6 Oktober 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023
29 Augustus 2023