Kathrein VOS 43/RA-1G2 Handleiding

Kathrein Receiver VOS 43/RA-1G2

Lees hieronder de 📖 handleiding in het Nederlandse voor Kathrein VOS 43/RA-1G2 (4 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
1 / 4
VOS 43/RA-1G2 209500001
House connection amplifi er
Basic safety precautions
House connection amplifi er for modern HFC networks up to
1,2 GHz
Integrated high-effi ciency switched-mode power supply unit
Power management: Unused amplifi er stage switch-off for
reduced power consumption
Die-cast housing with F-type connectors
Variable 6 dB interstage gain setting using on-board plug-in
attenuators (delivery condition: higher gain)
The maximum operational levels also apply for operation with
interstage attenuation
Interstage equaliser switchable with bridging plugs
(6 dB pre-emphasis)
Integrated return path 5 – 204 MHz active/passive, off
(switchable with bridging plugs)
Built-in variable attenuators (delivery condition return path:
max. attenuation) and variable equaliser
LED to indicate operational mode
Test socket on output -20 dB (with directional coupler)
Test socket on input -20 dB (Return path 5 – 204 MHz)
Test sockets are terminated with the EMK 03 in the delivery
status
For indoor installation
Conform to: EN 60728-11, EN 50083-2 und EN 32368-1
The amplifi ers comply with the EMC directive 2014/30/EU and
Low-Voltage Directive 2014/35/EU applicable at the time of
shipping
Installation must be carried out by authorised specialist staff .
Unplug from the mains before installation.
Described amplifi ers are exclusively for installation of HFC networks up to 1218 MHz.
Any other use or failure to comply with these instructions will void the warranty or guarantee.
The amplifi ers may only be installed in dry areas indoors. Do not install on or against highly combustible materials.
The amplifi ers must be earthed when installed (Cu, minimally 4 mm2).
The safety regulations set out in the current EN 60728-11 und EN 62368-1 standards must be complied with.
The supply voltage of the amplifi ers is 230 VAC which can be fatal if touched directly!
The only reliable method of disconnecting the amplifi ers from the mains is to unplug them.
Do not touch live parts.
The power plug must be easy to operate as the means of cutting power to the amplifi er, so the wall outlet must be
close to the amplifi er and easily accessible.
The amplifi ers may only be installed and deinstalled in the voltage-free condition.
Do not operate the amplifi ers without the factory- tted protective cover over the power supply unit. The cover must
be closed.
No liquid-fi lled items may be placed on top of the amplifi ers.
The amplifi ers are not to be exposed to dripping or splashing water.
Ambient temperature range -20 bis +55 °C.
Merkmale
2 / 4
Setting of the amplifi er
To adjust the settings, a Phillips screwdriver is required to remove the housing cover.
The settings options are also imprinted on the housing cover.
Forward path Return path
Pre-emphasis: 0 – 15 dB Pre-emphasis: 0 – 20 dB
② ⑥ Attenuation: 0 – 20 dB Attenuation: 0 – 20 dB
③ ⑦ Interstage → Attenuation: 6 dB Attenuation: 0 dB | 10 dB
Interstage → Pre-emphasis: 6 dB A | B | C: Operation mode return path: (see graphic
and block diagram)
Optionally available accessories
Mounting
De-emphasis equaliser: ERZ 120 (Order no. 272791)
Lightning arrester: KAZ 12 (Order no. 21810002)
③ ④
A B C
active
passive
off
A B C
VOS 43/RA-1G2
30
30
118
44
50
Convection space
40
3 / 4
The following is required for installation:
Fixings: screws, max. Ø 4.5 mm
F-type connector plug as per EN 61169-24
Risk of damage to property!
An inner cable conductor with a diameter greater than
1.2 mm, or the presence of burrs may damage the device
inputs/outputs beyond repair.
Max. 2 mm
excess length
Clamping torque
max. 3.4 Nm
(danger of over-
winding)
Diameter
0.6 - 1.2 mm free of burrs
Block diagram
Connection example
VOS 43/RA-1G2
ESM 30
(ESM 40/G)
KAZ 12
EAX 26/G
EBC 04/G
0 – 20 dB
0 dB
6 dB
Pre-emphasis
Pre-emphasis Attenuation
5 – 204 MHz
258 – 1218 MHz
Preemphase
Input
5 – 1218 MHz
dB
dB dB
CBA
dB
Test 1
5 – 204 MHz
-20 dB
0 – 20 dB
5 – 204 MHz
258 – 1218 MHz
0 – 20 dB 0 – 15 dB
0 dB
6 dB
0 dB
10 dB
Output
5 – 1218 MHz
Test 2
5 – 1218 MHz
-20 dB
active
passive
off
A B C
230 V~
Attenuation
Attenuation Attenuation


Product specificaties

Merk: Kathrein
Categorie: Receiver
Model: VOS 43/RA-1G2

Heb je hulp nodig?

Als je hulp nodig hebt met Kathrein VOS 43/RA-1G2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Kathrein

Handleiding Receiver

Nieuwste handleidingen voor Receiver