Kathrein UFO 83/CI Handleiding

Kathrein Niet gecategoriseerd UFO 83/CI

Lees hieronder de 📖 handleiding in het Nederlandse voor Kathrein UFO 83/CI (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/8
1 / 8
Head-end 8-way DVB-S(2)/-T(2)/-C – DVB-T (COFDM)
UFO 83/CI 20610136
About This Manual
This document is part of the product.
►Install and use the unit only after you have read and
understood this document.
►Keep this document for reference throughout the life of
the device. Pass this document on to the next owner
and user of the device.
For the current version of this manual, go to the Kathrein
website www.kathrein-ds.com.
Features
■Stand-alone head-end with 8-way multi-standard
frontend DVB-S(2)/-T(2)/-C, 6-way decoding (CI)
and 8output channels conforming to DVB-T (exibly
congurable)
■Outstanding output values due to direct implementa-
tion as FPGA solution
■High level of energy efciency
■4 Sat-IF inputs with DiSEqCTM
1.0 functionality for sat
multi-switches and 1terr./cable input, exibly distribut-
able across 8 multi-standard frontends
■Power supply for LNB and active antennas
■All transmission parameters can be set using the
USW800 conguration software
■Remote maintenance and conguration
■Comprehensive baseband signal processing with
channel lter functionality such as NIT, LCN
■Cascade capability for two head-ends (16-way multi-
standard frontend and 16xDVB-T) for common
conguration and NIT generation incl. LCN
■No fan, therefore no noise and no maintenance
Scope of supply
●UFO 83/CI
●Wall mounting plate
●User instructions
●Third Party Software Acknowledgement
Function blocks
8 x DVB-
S2/-T2/-C
4 x Sat-IF/
1 x terr./cable
DiSEqC™
Channel
filter 8 x DVB-T
Input Frontend Baseband Output
Special features
Energy-
efficient
Thermal
cut-out
Matrix
5 to 8
Power supply LNB
and
current antennas
3 Watt/COFDM
(typical) 1)
NIT
generation
CAT
matching
CAM
software info
Advanced
CAM
6 x Common
Interface
CAM info
CAM routing
Default service
configuration
Flexible
decoding
CAM
TS analysis
CAM
software
Update
Decoding
monitoring
CAM
Power On/Off
CAM
Multitype
Extended
LCN
processing
1) typical for the following input: 4x DVB-S, 2x DVB-S2, 2x DVB-T2, no LNB/antenna supply, without CAM
IMPORTANT
Read carefully
before use!
2 / 8
Intended Use
The UFO83/CI is used for transmodulation and decoding of DVB signals. The latest triple-tuner technology makes it
possible to receive up to eight DVB-S(2)/ -T(2)/ -C transponders. These can be received from the four SAT-IP inputs with
DiSEqC functionality and the terrestrial/cable input in any combination. The UFO83/CI delivers up to eight individually
congurable output channels conforming to DVB-T.
The highly efcient baseband signal processing offers channel lter, NIT, CAT and LCN functionality. In addition, there are
six CI slots and exibly combinable, highly energy efcient decoding options available.
The conguration is carried out by means of the USW800 management software over an IP interface. An optional
cascading of two units (UFO83 or/and UFO83/CI) is possible via a USB connection.
The unit is intended exclusively for the application in the UFG810 as well as in satellite, cable or antenna reception
systems. Any other use of failure to comply with these instructions will result in voiding of the guarantee or warranty.
General safety instructions
●The device can be connected to the power supply and disconnected from it only by means of the power plug. Make
sure that the connected power plug is always freely accessible and easy to reach.
●If the casing is damaged, do not connect the device to the power supply.
●If the device and/or the cables connected to it are damaged, immediately disconnect the system from the power
supply. Do not switch the system on again until
–the device has been repaired by the dealer or manufacturer,
–and the cables connected have been repaired by a competent person.
●Do not open the casing and do not modify the device. Otherwise the guarantee and warranty will become void.
Exception: Cover of the CI slots ( in Fig. 1,P.3)⑭
●Never cover the cooling ribs or the air circulation openings.
●Do not modify, remove or disgure the notices and markings applied by the manufacturer.
●Refer to the manufacturer's documentation before connecting external components other than those described
in this document (such as computers, network components). Incorrectly connected components can damage the
device.
●Refer to the current issue of the safety requirements EN60728-11 and EN60065.
●Disconnect the device from the power supply before performing mechanical work on the system.
WARNING
Risk of burns from hot surfaces!
In the event of a defect the heat sink of the unit may exceed 70°C.
►Do not touch the heat sink when the device is in operation or has recently been in operation.
Note
In the event of overheating, the device will shut down automatically and after it has cooled down will switch
on again automatically.
Transportation and Storage
►Transport and storage the unit in its original packaging.
►Protect the unit against dust, dirt, moisture and direct sunlight.
►Transport and store the unit in the permissible temperature range from –25 to +70°C. Make sure there is no water
condensation bildup.
3 / 8
Arrangement and function
Device elements
1
2
3
4
78
8
9
6
5
10
11
12
13
USB
UFO Link
14
Fig. 1: Device elements
①4x Sat-IF input, F socket ⑨Earthing screw
②1x terrestrial/cable input, F socket ⑩Power supply1)
③Screw for xing to the wall mounting plate ⑪Master LED; see below for more info.
④Test output, signal level –25dB, F socket ⑫Status LED; see below for more info.
⑤DVB-T output, F socket ⑬Reset button; see below for more info.
⑥Network port, RJ45 ⑭Cover of the CI slots
⑦USB port, type B, communications interface for connection to the UFOmini UFOlink master
2)
⑧2x USB ports, typeA:
USB: Software update by USB stick
UFO link UFOlink slave: Communications interface for connection to the UFOmini 3)
1) The power supply cable is integral to the device and is not shown here.
2) If the head-end is the slave; see below for more info , P.5.Cabling
3) If the head-end is the master; see below for more info , P.5. Cabling
LEDs and reset button
Master LED
green the head-end is the
master
off the head-end is a slave
Status LED
green OK
green, ashing software update in progress
red error
orange head-end starting
orange, ashing head-end is being identied by the
USW800 conguration software
Reset button
Press <5s1) the head-end .will reboot
Press >5s1) the head-end will reset to the and will reboot. factory settings Do not release the
reset button until the status LED lights up orange.
Press >5s1) the head-end will look for an update on the connected USB stick, perform the
update and reboot.2)
1) To prevent accidental activation, the reset button is recessed. To activate the reset button, use a tool such as a ball-point pen.
2) Pre-requirement: There is a valid update le on the USB stick. See the USW800 conguration software for more info.

Product specificaties

Merk: Kathrein
Categorie: Niet gecategoriseerd
Model: UFO 83/CI

Heb je hulp nodig?

Als je hulp nodig hebt met Kathrein UFO 83/CI stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Kathrein

Kathrein

Kathrein VOS 137/RA 2.0 Handleiding

24 Mei 2024
Kathrein

Kathrein UFOpro Handleiding

6 December 2023
Kathrein

Kathrein FRP 100 Handleiding

13 Juni 2023
Kathrein

Kathrein MS 6060 Handleiding

8 Juni 2023
Kathrein

Kathrein HDZ 66 Skew Handleiding

23 Mei 2023
Kathrein

Kathrein ZAS 90 Handleiding

19 Mei 2023
Kathrein

Kathrein EMK 104 Handleiding

14 Mei 2023
Kathrein

Kathrein UFZ 896 Handleiding

13 Mei 2023
Kathrein

Kathrein HDS 50 Handleiding

9 Mei 2023
Kathrein

Kathrein ESO 124 HL Handleiding

4 Mei 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Panasonic

Panasonic NB-W250 Handleiding

25 November 2024
Alpine

Alpine CHM-S611 Handleiding

25 November 2024
AOpen

AOpen DE3650-C Handleiding

25 November 2024
Lazer

Lazer Urbanize MIPS Handleiding

25 November 2024
Symmons

Symmons Dia 353GB-24 Handleiding

25 November 2024
SoundTube

SoundTube IPD-RS62-EZ Handleiding

25 November 2024
Moen

Moen Camerist 4905 Handleiding

25 November 2024
Lazer

Lazer Cameleon DLX Handleiding

25 November 2024
DMT

DMT DLD-85 Handleiding

25 November 2024
AOpen

AOpen AM1120T Handleiding

25 November 2024