Kathrein MS 6060 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Kathrein MS 6060 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
1 / 2
MS 4060 214500002
MS 6080 214500004
MS 6060 214500006
Mounting cabinet
Description
â–ºOn-wall mounting cabinet for protected installation of
active and passive components
â–ºFor indoor installation
â–ºFor the most up-to-date version of this document, go
to www.kathrein-ds.com
Variants
Mounting cabinet (1 door)
Perforated metal sheet
Warning label
Earthing cable 2x (A)
Nut M6 2x (B)
Washer 6.4 mm 7x (C)
Serrated lock washer 6.4 mm 4x (D)
Sheet metal screw 4x (E)
Mounting set small 1x (F)
Instructions for use
Scope of supply
MS 4060 400 x 600 x 200 mm
MS 6080 600 x 800 x 200 mm
MS 6060 600 x 600 x 200 mm
Wall mounting
â–ºUse four suitable dowels and corresponding screws or screw-dowel
systems. Choose the correct thread diameter, head diameter and screw
length for the respective mounting hole of the cabinet and the cabinet
weight including components.
Take into account that dierent wall types (e.g. masonry, concrete, ...)
require dierent mounting material.
The mounting material is not included.
Mounting notes
â–ºThe mounting cabinet may only be mounted in dry indoor areas. Do not mount it on or against easily
combustible material.
â–ºThe mounting cabinet must be provided with an equipotential bonding cable (Cu, at least 4 mm
2).
www.kathrein-ds.com | support@kathrein-ds.com 936500092/a/PM/0421/DE | Subject to change.
KATHREIN Digital Systems GmbH | Anton-Kathrein-Str. 1–3 | 83022 Rosenheim | Germany | Phone +49 731 270 909 70
Installing the earthing cable
Connecting the earthing cable to the door:
The earthing cable (A) must be connected as shown in Fig. 1. Put a
serrated lock washer (D), then the ring eye of the earthing cable (A),
a washer (C) and another serrated lock washer (D) onto the threaded
bolt of the cabinet door. Then screw a nut (B) onto the threaded bolt
and tighten it with a tool.
Connecting the earthing cable to the housing frame:
The earthing cables (A) must be connected as shown in Fig. 2. Put a
serrated lock washer (D), then the ring eye of the earthing cable (A), a
washer (C), the ring eye of the earthing cable (A), another washer (C)
and another serrated lock washer (D) onto the threaded bolt of the
housing frame. Then screw a nut (B) onto the threaded bolt and tighten
it with a tool. Use the sheet-metal screws (E) and the washers (C) to
mount the housing frame onto the rear wall (perforated metal sheet).
Connecting the earthing cable to the mounting plate (perforated metal sheet):
The earthing cable (A) must be connected as shown in Fig. 3. Use the
mounting set (F) to connect the earthing cable. First put the serrated
lock washer (M4), then the washer (M4) and then the small ring eye
of the earthing cable (A) onto the sheet-metal screw. Then screw the
screw into the mounting plate (perforated metal sheet).
Connecting the on-site PE conductor:
For integration into the protective equipotential bonding on site,
connect the PE conductor (H07V-U 4mm² Cu, solid) to the mounting
plate (perforated metal sheet) via the flat terminal using a U-clamp.
Must be connected as shown in Fig. 4.
All housing parts are to be connected using the washers and serrated lock washers in such a way that
current-carrying capacity and permanent contact are ensured.
The conductivity of the produced contacts must be tested and measured for all cabinet and mounting compo-
nents.
Attach the enclosed warning label to the outside of the cabinet door if required.
Figure 1
Figure 2
Figure 3
Figure 4


Product specificaties

Merk: Kathrein
Categorie: Niet gecategoriseerd
Model: MS 6060

Heb je hulp nodig?

Als je hulp nodig hebt met Kathrein MS 6060 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Kathrein

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd