Kathrein ESO 124 HL Handleiding

Kathrein Niet gecategoriseerd ESO 124 HL

Lees hieronder de 📖 handleiding in het Nederlandse voor Kathrein ESO 124 HL (6 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 58 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/6
1 / 6
ESO 90 H 237500001
ESO 120 H 237500002
ESO 124 H 237500003
ESO 124 HL 237500005
Refl ector Heating System for CAS 90, CAS 120 and CAS 124
Features
•Flexible special heating mat with integrated thermal insulation
and PTFE-insulated heating elements
•Good heat distribution due to an optimal fi t of the heating mat
on the refl ector
•Element carrier of aluminium foil, self-adhesive foil strips at
the front
•Thermal insulation made of bubble wrap with refl ective layer,
4 mm
•Built-in sensor to additionally defi ne the heating temperature
via a control
About These Instructions
This document is part of the product. These instructions
describe how to install and connect the refl ector heating
systems ESO 90 H, ESO 120 H, ESO 124 H and ESO 124 HL.
►Do not install or use the device until you have read and
understood this document.
►Keep this document for reference throughout the service life
of the device. Pass this document on to any new owner or
user.
The current version of this document can be found at
www.kathrein-ds.com
Scope of Supply
•1 x heating mat with 3 m cable (H05RNF) and heating tempe-
rature sensor
•Mesh reinforced aluminium foil, 0.05 x 5 m
•Adhesive fi lm (white) for covering the aluminium foil,
0.075 x 5 m
•5 x cable ties, 360 mm
ESO 90 H
•1 x heating mat with 3 m cable (H05RNF) and heating tempe-
rature sensor
•Mesh reinforced aluminium foil, 0.05 x 8 m
•Adhesive fi lm (white) for covering the aluminium foil,
0.075 x 8 m
•5 segments of white adhesive foil for covering the outer
contours of the heating mats
•5 x cable ties, 360 mm
ESO 120 H
ESO 90 H ESO 120 H
ESO 124 H/HL
ESO 124 HL:
For exposed locations, with
double the heating power
compared to ESO 124 H
(L = increased performance).
•1 x heating mat with 3 m cable (H05RNF) and heating tempe-
rature sensor
•Mesh reinforced aluminium foil, 0.05 x 8 m
•Adhesive fi lm (white), cut into di erent segments, for covering
the aluminium foil, 0.075 m wide
•4 segments of white adhesive foil for covering the outer
contours of the heating mats
•5 x cable ties, 360 mm
ESO 124 H, ESO 124 HL
2 / 6
Transport and Storage
►If possible, transport and store the heating mat in its original packaging.
►Protect the heating mat against moisture and mechanical damage.
►Transport and store the heating mat only in the permitted temperature range between -40 and +80°C. Make sure there is no
condensation build-up.
Functional Description
The electric heating system prevents snow and ice formation on the antenna refl ector surface which may lead to interruptions in
satellite reception. The heating for the antenna consists of a special heating mat with an integrated thermal insulation and PTFE-insu-
lated heating elements. The installed heating mat fi ts optimally on the refl ector and guarantees good heat distribution. The heating
mat has an integrated temperature switch that turns o the heating at 80°C so that the system can be operated at 230 V/50Hz. To
ensure e cient operation, we recommend the use of a control unit, which can be operated with or without the built-in sensor.
Possible system components:
Operation without temperature
sensor of the heating mat
Operation with temperature sensor
of the heating mat
Operation without control possible
(permanent operation)
ESO 90/120/124 H ESO 005, ESO 96 S, ESO 97 S ESO 97 SL, ESO 99 S YES
ESO 124 HL NO ESO 97 SL, ESO 99 S NO
DANGER!
Danger to life from electric shock when touching electrical installations!
►Disconnect all devices and units from the power supply during installation.
►In order to comply with the regulations for outdoor installation according to DIN VDE 0100 Part 610, it is recom-
mended to have a residual current circuit breaker with a residual current of 0.03 A installed.
►Make sure that installation and connection are only carried out by qualifi ed personnel.
►Make sure that modifi cations to electrical installations are only carried out by a specialist. Do not make any unautho-
rised changes yourself.
Installation and Safety Instructions
WARNING!
Risk of severe injuries during installation due to falling from or through the roof or falling parts!
►Wear sturdy shoes with non-slip soles.
►Use a working platform.
►Make sure that the person carrying out the installation or repair has a secure position to stand and hold on whilst
working.
►Make sure that the person carrying out the installation or repair does not su er from vertigo and can move around
safely on the roof or installation site.
►Make sure that the vehicle roof is su ciently strong and stable.
►Make sure that there is nobody underneath the antenna during installation/dismantling.
Intended Use
The ESO 90 H, ESO 120 H, ESO 124 H and ESO 124 HL are refl ector heating systems for the antennas CAS 90, CAS 120 and CAS 124.
They are used to prevent snow and ice formation on the antenna refl ector surface which could lead to interruptions in the satellite
reception. Any other use, or failure to comply with these instructions or documentation and instructions enclosed with the devices,
will result in voiding of warranty or guarantee. The following circumstances result in the loss of all warranty and liability claims
towards the manufacturer:
►Improper installation
►Use of non-specifi ed mounting materials, which cannot guarantee the mechanical reliability of the antenna system
►Structural changes or interference with the components and mounting accessories in the kit, which could endanger both the
mechanical and functional reliability
►Failure to observe installation and safety instructions in these instructions
3 / 6
Installing the Refl ector Heating
Required tools and equipment
•Knife
•Scissors
Installing the heating mat
Processing temperature
The most favourable processing temperatures (object temperature and ambient temperature) are between +15°C and +30°C. Proces-
sing below these temperatures is not recommended. Below the recommended temperatures, the adhesive may become too hard and
thus not achieve the desired adhesion.
The build-up of condensation must be avoided in any case. Condensation may build up when the adhesive tape and/or the surfaces
to be bonded are moved from a cold to a warmer environment. If this is the case, su cient time must be allowed after transport and
before bonding, so that all joining parts have the same temperature in the range indicated above.
1. Clean and degrease the antenna back panel.
The surface to be bonded must always be dry, free from dust, grease, oil, oxides, separating agents and other contaminants.
Isopropanol, ethanol, acetone, ethyl acetate, toluene or petrol can be used to remove dust, grease, oil, separating agents and
other contaminants. Other standard cleaning agents that do not leave any residues are also suitable. Please observe the respec-
tive safety regulations of the manufacturers of the solvents and cleaning agents.
2. Hold the heating mat on the antenna back panel to check the position.
Before fi nal bonding, place the heating mat on the back of the antenna and check if it fi ts correctly.
3. For a xing it, hold the heating mat in place.
CAUTION!
Risk of material damage due to the incorrect attachment of the heating mat!
If the heating mat is not attached to the antenna correctly, it can tear when the adhesive fi lm is being removed.
►Make sure that the heating mat is aligned correctly. To do so, place the heating mat fl ush with the outer edge
of the antenna and pay attention to equal distances at the antenna bracket. After the heating mat has been
a xed, a correction is no longer possible!
►If possible, ask a second person to hold the heating mat.
4. Gradually remove the protective fi lm from the adhesive surface and press the heating mat fi rmly in place.
5. Press the heating mat fi rmly to the antenna back panel. It can take up to 72 hours before the fi nal adhesive strength
is reached.
6. To prevent moisture and insects from entering the heating mat, adhere the mesh-reinforced aluminium foil all along
the edges of the mat.
7. Clean the surface to be covered with the mesh-reinforced aluminium adhesive tape (see 1.) to ensure the greatest
possible adhesive strength of the white adhesive foil.
8. Cover the aluminium adhesive tape with the white adhesive foil. Stick the outer contours of the heating mats with
the segments according to the labelling on the carrier foil.
ESO 120 H: Cover the remaining contours with the enclosed adhesive foil (75 mm wide).
ESO 124 H/HL: Cover the remaining contours with cut adhesive foil (see graphics on next page).

Product specificaties

Merk: Kathrein
Categorie: Niet gecategoriseerd
Model: ESO 124 HL

Heb je hulp nodig?

Als je hulp nodig hebt met Kathrein ESO 124 HL stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Kathrein

Kathrein

Kathrein VOS 137/RA 2.0 Handleiding

24 Mei 2024
Kathrein

Kathrein UFOpro Handleiding

6 December 2023
Kathrein

Kathrein FRP 100 Handleiding

13 Juni 2023
Kathrein

Kathrein MS 6060 Handleiding

8 Juni 2023
Kathrein

Kathrein HDZ 66 Skew Handleiding

23 Mei 2023
Kathrein

Kathrein ZAS 90 Handleiding

19 Mei 2023
Kathrein

Kathrein EMK 104 Handleiding

14 Mei 2023
Kathrein

Kathrein UFZ 896 Handleiding

13 Mei 2023
Kathrein

Kathrein HDS 50 Handleiding

9 Mei 2023
Kathrein

Kathrein ESO 124 HL Handleiding

4 Mei 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Panasonic

Panasonic NB-W250 Handleiding

25 November 2024
Alpine

Alpine CHM-S611 Handleiding

25 November 2024
AOpen

AOpen DE3650-C Handleiding

25 November 2024
Lazer

Lazer Urbanize MIPS Handleiding

25 November 2024
Symmons

Symmons Dia 353GB-24 Handleiding

25 November 2024
SoundTube

SoundTube IPD-RS62-EZ Handleiding

25 November 2024
Moen

Moen Camerist 4905 Handleiding

25 November 2024
Lazer

Lazer Cameleon DLX Handleiding

25 November 2024
DMT

DMT DLD-85 Handleiding

25 November 2024
AOpen

AOpen AM1120T Handleiding

25 November 2024