J.P. Instruments EDM-900 Handleiding

J.P. Instruments Niet gecategoriseerd EDM-900

Lees hieronder de 📖 handleiding in het Nederlandse voor J.P. Instruments EDM-900 (52 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 204 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/52

FAA Approved Installation Manual for the Report No 908

EDM-900 and EDM- 930 Page 1 of K52 Rev

Primary Engine Data Management System Date 5-02- 17

TABLE OF CONTENTS

Section Page

1. Revisions 2______________________________________________________________________________________

2. _________________________________________________________________________________ Read This First 2

3. Instrument Labeling ______________________________________________________________________________ 5

4. Primary TSO Label ______________________________________________________________________________ 5

5. Operation and Abbreviations ______________________________________________________________________ 6

6. Remote Alarm Light EDM 900 7_____________________________________________________________________

7. Locating and Installing the Indicator and Remote Alarm Display (RAD and Alert Light) _______________________ 10

8. EDM-900/930 Key information installation __________________________________________________________ 12

9. Routing the Wiring Harnesses _____________________________________________________________________ 13

10. Pressurized Aircraft wire Routing __________________________________________________________________ 13

11. Power Connection ______________________________________________________________________________ 14

12. Probe Wiring __________________________________________________________________________________ 14

13. Exhaust Gas Temperature Probe (EGT) Installation ___________________________________________________ 15

14. Cylinder Head Temperature (CHT) Probe Installation __________________________________________________ 16

15. Radial Engine CHT (spark plug gasket) _____________________________________________________________ 16

16. Outside Air Temperature (OAT) Probe Installation ____________________________________________________ 16

17. Oil Temperature Probe Installation ________________________________________________________________ 17

18. Oil Pressure Sensor Installation ___________________________________________________________________ 17

19. Fuel Pressure Sensor Installation using combination sensor _____________________________________________ 18

20. Ammeter Shunt Installation _______________________________________________________________________ 19

21. General Fuel Flow Transducer Installation __________________________________________________________ 20

22. ___________________________________________________________________ 22 Fuel Level Sender Wiring Types

23. _______________________________________________________________ 28 Fuel Flow Totalizer, Refuel Question

24. GPS Interface _________________________________________________________________________________ 28

25. Manifold Pressure (MAP) Sensor __________________________________________________________________ 28

26. RPM Sensor installation _________________________________________________________________________ 29

27. EDM-900/930 Specifications and Limitations _________________________________________________________ 31

28. EMI Radio Test and functional check:_______________________________________________________________ 32

29. Component Parts _______________________________________________________________________________ 33

30. Weight and Balance Data ________________________________________________________________________ 35

31. Pilot Programming _____________________________________________________________________________ 35

32. Programming the HP Constant ____________________________________________________________________ 36

33. Programming the MAP __________________________________________________________________________ 36

34. Selecting Fuel Pressure Type (EDM-900 only) ________________________________________________________ 36

35. Customizing Non Primary Data (EDM900 only)- ______________________________________________________ 37

36. K Factor ______________________________________________________________________________________ 37

37. Fine tuning the K Factor _________________________________________________________________________ 38

38. Adjusting the K Factor___________________________________________________________________________ 39

39. Programming Accumulate Trip Total _______________________________________________________________ 39

40. Trouble Shooting _______________________________________________________________________________ 40

41. GPS Interface Diagnostics _______________________________________________________________________ 41

42. _______________________________________________ 42 Connector Pin Assignments on EDM, J1 through J5

43. Connector Pin Assignments on EDM, J1 through J5 ___________________________________________________ 43

44. J3 RPM, MP, Oil-P _____________________________________________________________________________ 46

45. Appendix A onnector Pin Assignments on EDM, J1 J2 Only with ARINC 429C- _____________________________ 50

46. Appendix B ICA _______________________________________________________________________________ 51

The Owner of the EDM-900/930 must keep this manual

J.P. INSTRUMENTS

PO BOX 7033

HUNTINGTON BEACH CA

Last printed 5/1/2017 3:28:00 PM

FAA Approved Installation Manual for the Report No 908

EDM-900 and EDM- 930 Page 2 of K 52 Rev

Primary Engine Data Management System Date 5-02-17

1. Revisions

REV

Description

Date

Approval

Added new pictures of 900 and 930, page 6. Abbreviations page 4. Revised how the

JPI data base functions Added revision box. Page 2. Added fuel level , page 3.

calibration, page 22. Renumbered all pages.

9- - 28 2011

JFP

Revised to include new trouble shooting section for ICA and renumber pages. Updated

pressure sensors to i2s

12 02 2011- -

JFP

Revised TSO Label to show lighting change and added ARINC 429 wire chart

1- - 18 2013

JFP

Updated Part Numbers and Added new ICA and Pressure bulkhead paragraph

5- - 24 2014

JFP

Updated for new features adding digital fuel gauges with fuel flow monitoring per the

“Flight manual”

4- - 08 2016

JFP

2. Read This First

• The following notes apply to a new installation. Read this section before proceeding.

• The JPI warranty found in the back of the pilots guide clearly states that JPI will replace defective parts under

warranty, but does NOT cover labor to remove or install any parts.

• The most common cause of probe problems is poor terminal crimps. Crimp ring terminals with AMP tool or

equivalent. Fold back the wire double before crimping terminals.

• - - Do not use aluminum fittings or Teflon tape or pipe sealant with the FXT 201 or FXT 231 fuel flow transducer.

• -Write down the K factor engraved on the side of the fuel flow transducer here _______. Once the transducer is

installed and covered with the fire sleeve, you will not be able to access this K factor.

• Determine the locations of all holes before drilling to ensure that nothing interferes with the probe, clamp, clamp

screw or wire.

• Provide service loops at the instrument so that it can be moved for maintenance or troubleshooting.

• Thermocouple wire length is not critical. Trim to required length, allowing for service loops at the engine so that

probes can be swapped with probes on adjacent cylinders for troubleshooting purposes.

• Dress all wires away from high temperature components such as exhaust stacks.

• -Never splice thermocouple wire using copper wire. Use only K type thermocouple wire. Solder using zinc

chloride flux such as Nokorode brand rosin flux alone – will not work.

• Observe correct polarity on all probe wires. Connect like colors together (red to red, yellow to yellow).

• The instrument must be grounded at the engine, not at the avionics ground.

• - - Record the installation of the EDM 900 or EDM 930 on a FAA form 337. Make an entry in the aircraft logbook.

• Note: Removal of probes, sensors and the instrument is the reverse of the installation procedure.

FAA Approved Installation Manual for the Report No 908

EDM-900 and EDM- 930 Page 3 of K 52 Rev

Primary Engine Data Management System Date 5-02-17

Do not install a non 900/930 in a certified aircraft. A certified EDM 900/930 lists see AML- -certified EDM -

If the EDM 900/930 is configured to monitor the aircrafts fuel tanks, the EDM 900/930 must be calibrated to the - -

aircraft fuel system and the EDM 900/930's accuracy must be verified before flying the aircraft.-

Before allowing the aircraft to be flown, verify the instrument markings displayed on the EDM 900/930 screens are -

accurate with the aircraft’s POH for every function displayed on the EDM-900/930.

The use of the EDM 900/930 requires recurring training for any pilot who will be flying the aircraft in which it is -

installed. Recurring training should include reading the EDM 900/930 Installation Manual and seeking a flight -

instructor for proper interpretation of information being displayed to the pilot.

Fuel Level Accuracy Limitations:

1. Angle of Attack - - The EDM 900/930 must be calibrated with the aircraft in a cruise angle of attack. If

the aircraft is in an angle of attack other than cruise, the EDM-900/930 may display inaccurate fuel levels

(depending on the mounting location and type of sensor used). If your aircraft does not sit at a cruise

angle of attack when on the ground, it may not display accurate fuel levels. Test your aircraft at

different angles of attack to see the effects on the EDM 900/930 fuel level readings.-

2. Full Fuel Readings - As a tank is filled the fuel sensor may not be able to detect the fuel entering

the upper corners of the fuel tank. If this is the case with your sensor, the EDM 900/930 will display lower-

fuel levels than the actual fuel in the tanks when the tanks are full. When the fuel level drops to a

point where the fuel sensor starts to detect a change, the displayed fuel level should be accurate.

Check the accuracy of your system by comparing the displayed fuel levels on the EDM-900/930

to the fuel levels listed in the flight manual at each fill up.

3. Low Fuel Readings - - Do not rely on the EDM 900/930 to determine the fuel level in the tank

for an indicated tank level below 1/8. You should always fly the aircraft in such a manner as to

maintain at least the FAA minimum fuel requirements in the aircraft at all times.

4. Improper Calibration - - If the EDM 900/930 has not been properly calibrated it will not display accurate

fuel levels in the tanks. It is important you verify the accuracy of the EDM 900/930. Always crosscheck-

your measured fuel levels in the tanks with the readings on the EDM 900/930 before each flight.-

5. Poor Connections - Poor connections between the wires leading from the EDM to the fuel

sensors can become intermittent. An intermittent connection most likely will show up as wandering or

inaccurate readings on the EDM 900/930. Always crosscheck your measured fuel levels in the tanks-

with the readings on the EDM-900/930 before each flight.

6. Defective Fuel Level Sensors - Fuel sensors can become intermittent or change resistance

with age. It is not uncommon to find intermittent problems even in new sensors. An intermittent

problem with a fuel sensor most likely will show up as wandering or inaccurate readings on the EDM-900/930.

Always crosscheck the measured fuel levels in the tanks with the readings on the EDM-900/930 at

each fill up. If you ever find an inaccuracy issue or any other problem with a fuel level display on

the EDM-900/930, troubleshoot and fix the problem before the next flight.

DETERMINE THE FUEL LEVELS IN THE AIRCRAFT.

1.The use of the EDM-900/930 does not eliminate or reduce the necessity for the pilot to use good flight planning,

preflight and in flight techniques for managing fuel. It is important the pilot adopt the practices listed below. If you -

are not familiar with these techniques, contact the FAA to acquire proper training.

2. Flight Planning - Always calculate the fuel requirement for each leg of a flight, including any

alternate plans for bad weather. Keep this information available in the aircraft during the

flight. Keep a chart of the published fuel flows for various flight/engine conditions in the

Product specificaties

Merk:	J.P. Instruments
Categorie:	Niet gecategoriseerd
Model:	EDM-900

Heb je hulp nodig?

Als je hulp nodig hebt met J.P. Instruments EDM-900 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd J.P. Instruments

J.P. Instruments EDM-900 Handleiding

15 Augustus 2023

J.P. Instruments EDM-930 Handleiding

15 Augustus 2023

J.P. Instruments EDM-830 Handleiding

15 Augustus 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Zipper ZI-UVGW1 Handleiding

15 November 2024

Dimplex Optiflame 3D GLN20BR3D Handleiding

15 November 2024

Tesla MultiCook M90 Premium Handleiding

15 November 2024

Scott AirFlex Pro Back Protector Handleiding

15 November 2024

Scott AirFlex Junior Back Protector Handleiding

15 November 2024

AVM FRITZ!WLAN USB Stick AC 860 Handleiding

14 November 2024

Nedis ANOR5G10WT Handleiding

14 November 2024

Nedis ANOR5G20WT Handleiding

14 November 2024

LAS 16271 Handleiding

14 November 2024

LAS 16275 Handleiding

14 November 2024