Joovy Tricycoo 0017X Handleiding

Joovy Babyproducten Tricycoo 0017X

Lees hieronder de 📖 handleiding in het Nederlandse voor Joovy Tricycoo 0017X (12 pagina's) in de categorie Babyproducten. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

USA: Joovy • 2919 Canton Street • Dallas, TX 75226 • Tel: (877) 456-5049 • Fax: (214) 761-1774 • Email: customerservice@joovy.com • Website: www.joovy.com

CANADA: ISSI Inc. • 2400A Autoroute Transcanadienne • Pointe-Claire, QC, H9R 1B1 • Tel: (800) 667-4111 • Montreal: (514) 344-3045 • Email: service@issibaby.ca

Patent/Brevet/Patente: www.joovy.com/patents

Tricycoo™

0017X

EN FR ES

Baby Surround Base

Inner Rear Wheel Hubs

Baby Surround Arms

Baby Surround

Connector

Black Secondary

Arm Locks (attached to baby

surrond arms)

Washer

Head Screws Handlebar

Bolt (Short)

Pointed

Phillips Head Screw Nylock Nut

Large

Washer

Snap Pin

Small

Washer

Tool Bell

Cover Cap

Knob Nut Knob Screw Spacer

Seat

Fender

Hubcaps

Axle Tricycle Frame

Rear Wheels

Push Handle

Basket

Handlebar

Front Wheel

Handlebar Caps

Front Back

(2)

Optional Baby Surround Parts

!WARNING

Please read this instruction manual completely before using this product.

Keep these instructions for future reference.

• TO AVOID SERIOUS INJURY

• Continuous adult supervision is required.

• Never use near motor vehicles.

• Never use near streets, swimming pools, hills, steps, or sloped driveways.

• Always wear shoes when using the tricycle.

• Allow only one rider.

• Minimum age of rider shall be 1.5 years.

• Maximum weight of rider shall be 44 lbs. (19.96 kg).

• The baby surround system should be used for children who are not yet capable of sitting in the seat without support

or who are not capable of pedaling the product by themselves.

• RidershouldalwayswearaproperlyttedhelmetthatcomplieswithFederalhelmet(16CFR1203)requirements.

• Do not load the basket with more than 2.2 lbs. (1.0 kg). Excessive weight may cause a hazardous or unstable

condition.

Please do not return this product to the store

If you experience any difculty with the assembly or use of this product, or if you have a question regarding these

instructions, please contact our Customer Service Department:

UNITED STATES – Joovy: (877) 456-5049, Hours 8:30 am – 5:00 pm Central Time.

CANADA – ISSI Inc.: (800) 667-4111, Hours 8:30 am – 5:00 pm Eastern Time.

Please note: Styles and colors may vary.

1 Unpacking the Product

• Carefully remove all parts from the box and plastic bag.

• Identify the parts (axle, tricycle frame, handlebar, front wheel, fender, inner rear wheel hubs (2), hubcaps (2), rear wheels (2), push handle

(2 separate components), baby surround connector, baby surround base, baby surround arms (2), black secondary arm locks (attached

to baby surround arms) (2), basket, knob nut, knob screw, seat screw, spacer (2 separate components), seat, handlebar cap (front and

back), tool, cover cap, bell, larger washer, small washer, lock washer, washer head screws (2), seat bolt (long), handlebar bolt (short),

pointed Phillips head screw, nylock nut, snap pin, and documents [not shown]) with the pictures in the Parts Figure.

NOTE: Extra washers and snap pins may be included.

• Discard all packaging materials properly.

• Remove the plastic coverings from any areas of the product and discard also.

• DO NOT allow children to play with any packaging materials.

Parts Figure

Lock

Washer Seat

Bolt (Long)

EN FR ES

!WARNING

Adult assembly required. Tools required (not included): Phillips Screwdriver. Choking Hazard to children under the

ageof3years–containssmallpartspriortoassembly.Somescrewsmayhavesharpedgesandsharppoints.

Keep all small parts out of reach of children at all times.

2 Installing the Rear Wheels

• Keep children away while assembling.

• Insert an Inner Rear Wheel Hub into either end of the rear axle cylinder on the rear of the tricycle frame. See Figure 1.

• Insert the axle into one of the rear wheels (ensuring that the side with the 8 holes faces out). Slide the axle (with the Rear Wheel) through

the Inner Rear Wheel Hub and the rear axle cylinder. See Figure 2.

• Insert the other Inner Rear Wheel Hub into the opposite end of the rear axle cylinder.

• Slide the other Rear Wheel over the axle (ensuring that the side with the 8 holes is facing out). Slide the large washer over the axle.

• Insertthesnappinstraightlegintothesmallholeintheaxle.Pushitrmlyintothisholeuntiltheroundportionoftheotherlegsnaps

completely around the outside of the axle. See Figure 3.

NOTE: The snap pin is curved (concave) to make insertion easier.

• Install a hubcap onto each wheel by aligning the 4 tabs with the 4 slots in the wheel. Ensure that ALL 4 tabs have engaged securely

and the hubcaps cannot be pulled off. See Figure 4.

3 Front Wheel Assembly

• Place the fender onto the front wheel tube making sure you push the fender all the way down. See Figure 5.

• With the long part of the fender facing forward insert the front wheel tube into the front steering hub of the tricycle frame. See Figure 5.

• Identify the 2 piece spacer (assemble if necessary) and slide it over the top of the front wheel set. Make sure to push the spacer all the

way down. See Figure 6.

IMPORTANT NOTE:

If you intend to use the optional baby surround system, slide the baby surround connector onto the tricycle frame.

See Figure 7. If not using the baby surround system then disregard this NOTE.

4 Handlebar Assembly

NOTE: If not using the baby surround system, make sure that the baby surround connector is NOT attached to the tricycle frame.

• Insert the handlebar onto the front wheel tube. See Figure 8.

NOTE: The handlebars should be mounted with the bars leaning forward.

• From the front of the product, insert the handlebar bolt (short) into the middle hole of the handlebar column and push it all the way

through. Attach the Nylock nut to the bolt and tighten using the tool provided. See Figure 9.

• Fit the front half of the handlebar cap through the bottom hole on the front of the handlebar.

• Snap the back half of the handlebar cap to the front. Secure the handlebar caps with the pointed Phillips head screw. See Figure 10.

NOTE: Pull on the handlebar and the handlebar caps to make sure they are secure.

5 Seat Assembly

• Place the seat onto the frame facing forward and line up the hole in the tricycle frame. See Figure 11.

• Secure the seat with the small washer, the lock washer, and the seat bolt (long). Tighten the screw securely. See Figure 12.

• Pull on the seat to ensure that it is secure.

6 Push Handle Assembly

• Place the basket onto the rear of the tricycle frame with the opening over the rear steering tube. See Figure 13.

• Next place the cover cap onto the rear steering tube. See Figure 14.

• Insert the upper half of the push handle into the end of the lower handle tube that has the plastic knob on it. Insert it so that the pin on the

upper handle is aligned with the holes in the lower tube and push down until a click is heard and the pin can be seen protruding from one

of the holes. Pull on the upper half to be sure it is secure. See Figure 15. For push handle adjustment, see Section 11.

• Insert the push bar into the rear steering tube in the back of the tricycle frame. Make sure to line up the hole in the push bar with the hole

in the tube.

• Insert the knob screw through the hole and secure with a knob nut. Tighten the nut securely. See Figure 16.

!WARNING

The baby surround system should be used for children who are not yet capable of sitting in the seat

without support or who are not capable of pedaling the product by themselves.

7 Attaching/Detaching the Baby Surround (OPTIONAL)

NOTE: If you are not using and have not attached the baby surround connector then skip these steps in this section.

• Insert one of the baby surround arms into one of the sides of the baby surround base.

• Fasten securely in place with a washer head screw. See Figure 17.

• Repeat these steps for the other surround arm.

• Place the baby surround base on the top of the seat back and push down until a click is heard. See Figure 18.

• Pull up on the base to ensure that it is secure.

• Identify the small black secondary arm lock on each arm and note their locked position. Remove each of them by pulling out on the bottom

tabs, and then pulling up on the lock. See Figure 19.

Product specificaties

Merk:	Joovy
Categorie:	Babyproducten
Model:	Tricycoo 0017X

Heb je hulp nodig?

Als je hulp nodig hebt met Joovy Tricycoo 0017X stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Babyproducten Joovy

Joovy Groove 2 320 Handleiding

12 Juni 2023

Joovy Noodle 0011X Handleiding

12 Juni 2023

Joovy 41X Handleiding

12 Juni 2023

Joovy Caboose Too Rear Seat Handleiding

12 Juni 2023

Joovy Caboose 40xX Handleiding

12 Juni 2023

Joovy Peg Perego Car Seat Adapter Handleiding

12 Juni 2023

Joovy Groove 350 Handleiding

12 Juni 2023

Joovy Tricycoo 0017X Handleiding

12 Juni 2023

Joovy Platoon Handleiding

12 Juni 2023

Joovy Toy Caboose Handleiding

12 Juni 2023

Handleiding Babyproducten

Nieuwste handleidingen voor Babyproducten

BeSafe Mirror XL 2 with light Handleiding

12 Oktober 2023

BeSafe iZi Transfer Handleiding

12 Oktober 2023

BeSafe Sunshades Handleiding

12 Oktober 2023

BeSafe Pregnant Handleiding

12 Oktober 2023

BeSafe Insect and Sun Shield Handleiding

12 Oktober 2023

BeSafe Rain Shield Handleiding

12 Oktober 2023

BeSafe Car Seat Protector Handleiding

12 Oktober 2023

BeSafe Belt Guard Handleiding

12 Oktober 2023

BeSafe Mirror XL with light Handleiding

12 Oktober 2023

Jane Steriliser - 10370 Handleiding

12 Oktober 2023