JL Audio Stealthbox SB-T-TACDC12/10TW3 Handleiding

JL Audio Subwoofer Stealthbox SB-T-TACDC12/10TW3

Lees hieronder de 📖 handleiding in het Nederlandse voor JL Audio Stealthbox SB-T-TACDC12/10TW3 (4 pagina's) in de categorie Subwoofer. Deze handleiding was nuttig voor 4 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
I N S T A L L A T I O N G U I D E
for the
SB-T-TACDC12/10TW3
SKU# 94557
2012 & Up Toyota Tacoma Double Cab
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.
With proper installation, your new vehicle-specific enclosed subwoofer system
will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your authorized
JL Audio dealer. The installation professionals employed by your dealer have the necessary tools
and experience to disassemble and reassemble your vehicle properly. If you prefer to perform your
own installation, please read this installation guide completely before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox ® be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
Continued on Next Page
SB-T-TACDC12/10TW3 INSTR_SKU# 011350
INSTALLATION
D I F F I C U LT Y :
25
OUT
OF
ESTIMATED TIME:
2 HOURS
S P E C I F I C A T I O N S
Enclosure Type: Sealed
Driver Type: 10TW3-D4
Nominal Impedance: 2 ohms
Continuous Power Handling: 400 watts (RMS method)
I N C L U D E D H A R D W A R E
(2) Brackets
(4) 1/4 - 20 x 1” Hex Bolt
(4) 1/4” Lock Washer
(4) 1/4” Flat Washer
(2) 1/4 - 20 U-Nut
SB-T-TACDC12/10TW3 INSTR_SKU# 011350
P O W E R R E C O M M E N D A T I O N
JL Audio recommends high quality ampliers such as the JL Audio XD300/1. The diagram below shows the recommended crossover settings for the XD300/1. For a detailed description of the amplier settings, consult the
owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.
C O N N E C T I O N S
Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your Stealthbox® amplier. Other kits
are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for both channels of the amplier. JL Audio
reccomends using 12AWG speaker wire for subwoofers.
Continued on Next Page Page 2 • JL Audio, Inc., 2013
Continued on Next Page
SB-T-TACDC12/10TW3 INSTR_SKU# 011350
Page 3 • JL Audio, Inc., 2013
S T E P 4
On the backside of the rear panel, locate the two recessed
areas, then measure and mark 1” down the center from the
edge as shown. Drill a 1/8” pilot hole on the mark.
S T E P 8
Slide a 1/4 - 20 U-Nut through each of the 3/4” holes and
align them with the 7/16” holes as shown.
S T E P 3
Empty out the storage pocket. Remove the clips that hold in
the rear panel and remove the panel.
S T E P 7
Drill 3/4” holes on the marks made in the previous step. Use
caution so as not to drill through the back of the cab.
S T E P 2
Carefully unclip the seat bolt covers at the corners of the rear
seat backs. Unbolt and remove the seat backs.
S T E P 6
Measure and mark 1” to the right of each pilot hole. Enlarge
the 1/8” pilot holes in both the metal and the plastic to 7/16”.
Use caution so as not to drill through the back of the cab.
S T E P 1
Empty out the back seat of the vehicle and fold the seats
down.
S T E P 5
Reinstall the panel. Drill through the pilot holes made in the
previous step to create pilot holes in the metal. Use caution
so as not to drill through the back of the cab. Remove the
panel again.
Before drilling, always make sure that you are not
going to be drilling into any gas lines, brake lines,
tires, transmission lines, electrical wiring, exhaust
systems or anything else that might cause a reduction
in your weekly pay.
Always wear eye protection when drilling!

Product specificaties

Merk: JL Audio
Categorie: Subwoofer
Model: Stealthbox SB-T-TACDC12/10TW3

Heb je hulp nodig?

Als je hulp nodig hebt met JL Audio Stealthbox SB-T-TACDC12/10TW3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Subwoofer JL Audio

JL Audio

JL Audio Stealthbox SB-F-150-SPRCRW/13TW5v2/GA Handleiding

15 November 2024
JL Audio

JL Audio Stealthbox SB-F-MUCUPE2/13W3v3 Handleiding

15 November 2024
JL Audio

JL Audio Stealthbox SB-GM-SLVCRW/10TW3 Handleiding

15 November 2024
JL Audio

JL Audio Stealthbox SB-T-TACDC12/10TW3 Handleiding

15 November 2024
JL Audio

JL Audio StowAway PES112-TW1 Handleiding

11 Juni 2024
JL Audio

JL Audio Fathom CTS-113-ST575-13TW5H Handleiding

10 Juni 2024
JL Audio

JL Audio Fathom CTS-213-TD900-13TW5H Handleiding

10 Juni 2024
JL Audio

JL Audio Fathom CTS-113-SD1400-13TW5H Handleiding

10 Juni 2024
JL Audio

JL Audio Fathom ICS-SYS-208 Handleiding

8 Januari 2024
JL Audio

JL Audio Fathom ICS-SYS-108 Handleiding

8 Januari 2024

Handleiding Subwoofer

Nieuwste handleidingen voor Subwoofer

Klipsch

Klipsch RSW-10 Handleiding

15 November 2024
Dynacord

Dynacord PowerSub 312 Handleiding

14 November 2024
JBL

JBL ARC SUB Handleiding

13 November 2024
Klipsch

Klipsch KI-215-SMA-II Handleiding

13 November 2024
Klipsch

Klipsch KI-115-SMA-II Handleiding

13 November 2024
Polk

Polk Signature Elite ES8 Handleiding

12 November 2024
Kicker

Kicker 50CVX124 Handleiding

12 November 2024
Kicker

Kicker 50CVX154 Handleiding

12 November 2024
Polk

Polk Signature Elite ES12 Handleiding

12 November 2024
Deaf Bonce

Deaf Bonce Machete MF-15S D2/D4 Handleiding

12 November 2024