JL Audio Stealthbox SB-GM-SLVCRW/10TW3 Handleiding

JL Audio Subwoofer Stealthbox SB-GM-SLVCRW/10TW3

Lees hieronder de 📖 handleiding in het Nederlandse voor JL Audio Stealthbox SB-GM-SLVCRW/10TW3 (5 pagina's) in de categorie Subwoofer. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/5
I N S T A L L A T I O N G U I D E
for the
SB-GM-SLVCRW/10TW3
SKU# 94574
2001 - 2006 Chevrolet Silverado/GMC Sierra Crew Cab
2007 Crew Cab Classic” Trucks
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.
With proper installation, your new vehicle-specific enclosed subwoofer system
will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your authorized
JL Audio dealer. The installation professionals employed by your dealer have the necessary tools
and experience to disassemble and reassemble your vehicle properly. If you prefer to perform your
own installation, please read this installation guide completely before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox ® be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
Continued on Next Page
SB-GM-SLVCRW/10TW3 INSTR_SKU# 011364
INS TALLATION
D I F F I C U L T Y :
25
OUT
OF
ESTIMATED TIME:
2 HOURS
S P E C I F I C A T I O N S
Enclosure Type: Sealed
Driver Type: 10TW3-D4 (x 2)
Nominal Impedance: 4 ohms
Continuous Power Handling: 800 watts (RMS method)
I N C L U D E D H A R D W A R E
(2) Large Bracket
(2) Small Bracket
(4) U-Nut
(2) 3/8 - 16 x 2-1/4” Set Screw
(2) 1/4” Spacer
(2) 1/4 - 20 x 1/2” Flange Bolt
(2) 1/4 -20 Flange Nut
(2) 3/8 - 16 x 3/4” Flange Bolt
(2) 3/8” Fender Washer
(2) 3/8” Lock Washer
(2) 3/8” Hex Nut
SB-GM-SLVCRW/10TW3 INSTR_SKU# 011364
P O W E R R E C O M M E N D A T I O N
JL Audio recommends high quality ampliers such as the JL Audio HD750/1. The diagram below shows the recommended crossover settings for the HD750/1. For a detailed description of the amplier settings, consult the
owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.
C O N N E C T I O N S
Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbo. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your Stealthbo amplier. Other kits
are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for both channels of the amplier. JL Audio
reccomends using 12AWG speaker wire for subwoofers such as our XC-BCS12-25.
Continued on Next Page Page 2 JL Audio, Inc., 2013
Continued on Next Page
SB-GM-SLVCRW/10TW3 INSTR_SKU# 011364
Page 4 • JL Audio, Inc., 2013
S T E P 4
Locate the two rectangular holes just outside the outer child
safety lock holes.
S T E P 8
Remove the U-Nut, and enlarge the pilot hole drilled in the
previous step to 9-16. Use caution as to not hit the outer
cab wall.
Before drilling, always make sure that you are not
going to be drilling into any gas lines, brake lines,
tires, transmission lines, electrical wiring, exhaust
systems or anything else that might cause a reduction
in your weekly pay.
Always wear eye protection when drilling!
S T E P 3
If equipped, remove the snaps that hold the top of the
carpet to the back of the cab.
S T E P 7
Using a 19/64” drill bit, drill a pilot hole into the back of the
cab through the U-Nut. Use caution as to not damage the
threads of the U-Nut or hit the outer cab wall.
Before drilling, always make sure that you are not
going to be drilling into any gas lines, brake lines,
tires, transmission lines, electrical wiring, exhaust
systems or anything else that might cause a reduction
in your weekly pay.
Always wear eye protection when drilling!
S T E P 2
Carefully unclip and remove the upper plastic trim panel.
S T E P 6
Slide a U-Nut in backwards through the rectangular hole as
shown.
S T E P 1
Fold down the rear seats and empty the area behind them.
S T E P 5
In vehicles where the carpet covers these rectangular holes,
the carpet will need to be cut as shown.


Product specificaties

Merk: JL Audio
Categorie: Subwoofer
Model: Stealthbox SB-GM-SLVCRW/10TW3

Heb je hulp nodig?

Als je hulp nodig hebt met JL Audio Stealthbox SB-GM-SLVCRW/10TW3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Subwoofer JL Audio

Handleiding Subwoofer

Nieuwste handleidingen voor Subwoofer