JL Audio MX10IB3 Handleiding

JL Audio Subwoofer MX10IB3

Lees hieronder de 📖 handleiding in het Nederlandse voor JL Audio MX10IB3 (4 pagina's) in de categorie Subwoofer. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
Thank you for choosing a JL Audio Marine Subwoofer.
With proper installation, your new speaker
will deliver years of listening pleasure.
We strongly recommend that you have your subwoofer installed
by your authorized JL Audio dealer. The installation
professionals employed by your dealer have the necessary tools and experience to
properly install this product. If you prefer to perform
your own installation, please read this instruction manual
completely before beginning the process.
owner’s manual
Marine Subwoofer
MX10IB3
2 JL AUDIO MX10IB3
A
C
B
E
D
INSTALLATION PROCEDURE
The diagram above shows the typical
installation procedure into a fiberglass panel using
the supplied hardware. Always follow proper
safety procedures when working on a vessel.
Before cutting, drilling or inserting any screw, check
clearances on both sides of the planned mounting
surface. Also check for any potential obstacles, such
as wiring harnesses, fuel lines, hydraulic lines, etc.
Use
eye-protection at all times and a dust mask and
gloves when cutting.
1) Choose a flat mounting surface that has
sufficient
depth and air space behind it to accept
the subwoofer.
2) Cut a 8.875-inch (225 mm) diameter hole.
3) Run the speaker cable to the mounting location.
4) Place the woofer in the hole and mark the screw
hole locations using a sharp, pointed tool.
5) Remove the woofer and drill a pilot hole
(see chart on next page) in each of the screw
locations. It is also advisable to use a hand-driven
countersink tool on each hole to further inhibit
gel-coat cracking of fiberglass panels.
6) Connect the speaker wires and place the woofer,
with its grille in place, into the opening
7) While holding the speaker firmly in its mounting
location, evenly snug the mounting screws in a
criss-cross pattern, then hand tighten in a criss-
cross pattern.
Non-standard installations may require different
hardware. Always use marine-grade, stainless-steel
fasteners to ensure a secure, reliable installation.
We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers.
We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely
affect performance.
A l l s p e c i f i c a t i o n s a r e s u b j e c t t o c h a n g e w i t h o u t n o t i c e .
PHYSICAL SPECIFICATIONS
INCLUDED PARTS
• Six #8 x 1 3/8-inch (35 mm) phillips pan-head
stainless-steel screws
• Six #8 stainless-steel washers
Subwoofer Physical Specifications
Nominal Diameter: 10 in. / 250 mm
Overall Diameter (A): 10.75 in. / 273 mm
Mounting Hole Diameter (B): 8.875 in. / 225 mm
Bolt Hole Circle (C): 9.706 in. / 247 mm
Motor Overmold Outer Diameter (D): 5.29 in. / 134 mm
Mounting Depth (E): 5.12 in. / 130 mm
Net Weight: 6.5 lbs. / 2.94 Kg
Driver Displacement: 0.04 ft 3 / 1.13 litres
Subwoofer Parameters MX10IB3
Free Air Resonance (Fs): 41.84 Hz
Electrical “Q” (Qes): 0.806
Mechanical “Q” (Qms): 11.751
Total Speaker “Q” (Qts): 0.754
Equivalent Compliance (Vas): 1.29 ft3 / 36.53 litres
One-way, Linear Excursion (Xmax)*: 0.42 in. / 10.7 mm
Efficiency (1W/1m)**: 87.23 dB SPL
Effective Piston Area (Sd): 50.68 in² / 0.0327 m²
DC Resistance (Re): 3.957 ohm
Nominal Impedance: 4 ohm
Infinite Baffle Use: Yes
Enclosure Use: Yes (Sealed Only)
Power Handling (continuous): 175W
* Xmax specifications are derived via one-way voice coil overhang method with no correction factors applied.
** Efficiency (1W/1m) is not an accurate indicator of a subwoofer’s output capability and should not be used
as a comparison to other subwoofers to determine which one is “louder” !
The enclosure recommendations listed are external dimensions which assume the use of 3/4” (19mm) thick material. If you are using 5/8” (16mm) thick material, subtract 1/4”
(6.5mm) from each dimension. Do not use any material with a thickness of less than 5/8” (16mm) as this may compromise the rigidity of the enclosure.
All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal
volume. All enclosure dimensions listed have already taken this into account.
JL AUDIO MX10IB3 3
! ! CAUTION ! !
While this speaker is designed to be water and
spray resistant, it is not designed to be submerged
or to withstand high-pressure water spray.
Please exercise care when washing your boat to
avoid damaging your speaker. Do not install on
submersibles, personal watercraft or any other
vessel likely to be under water at any time.
Prolonged exposure to sound pressure levels in
excess of 100dB can cause permanent hearing loss.
This high-performance speaker can exceed this
level. Please exercise restraint in its operation in
order to preserve your ability to enjoy its fidelity.
When installing a subwoofer in your vessel, it is
extremely important to secure it firmly. This applies
not only to the woofer itself, but also the structure
it is mounted to. If not firmly attached, the speaker
can become a dangerous projectile in a collision.
Please review the mounting information carefully
and use the supplied marine-grade hardware to
mount this product.
A l l s p e c i f i c a t i o n s a r e s u b j e c t t o c h a n g e w i t h o u t n o t i c e .
Fiberglass Thickness Recommended Pilot Hole Drill Size
0.125 in. (3.18 mm) or less 7/64 in. (2.78 mm) pilot hole
foam core / fiberglass sandwich 7/64 in. (2.78 mm) pilot hole
larger than 0.125 in. (3.18 mm) 1/8 in. (3.18 mm) pilot hole
#8 SCREW: PILOT HOLE RECOMMENDATIONS
SUBWOOFER INSTALLATION DIAGRAM
Subwoofer Recommended Sealed Design
Volume
(net int.)
External Dimensions
( idth x eight x epth)W H D
F3
(Hz)
Fc
(Hz) Qtc
MX10IB3 2.0ft3
56.6 litres
18 in. x 18 in. x 14.5 in.
457 mm x 457 x 368 mm 42.9 53.66 0.967
Sealed Design
ENCLOSURE SPECIFICATIONS
NOTE: The MX10IB3 Marine Subwoofer is not
recommended for use in Ported Enclosures.

Product specificaties

Merk: JL Audio
Categorie: Subwoofer
Model: MX10IB3

Heb je hulp nodig?

Als je hulp nodig hebt met JL Audio MX10IB3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Subwoofer JL Audio

JL Audio

JL Audio Stealthbox SB-GM-ESC/10W1v3/TN Handleiding

7 December 2024
JL Audio

JL Audio Stealthbox SB-GM-CTRIP/10TW3/UF Handleiding

7 December 2024
JL Audio

JL Audio Stealthbox SB-N-370/10W3v3 Handleiding

7 December 2024
JL Audio

JL Audio Stealthbox SB-F-150-SPRCRW/13TW5v2/GA Handleiding

15 November 2024
JL Audio

JL Audio Stealthbox SB-F-MUCUPE2/13W3v3 Handleiding

15 November 2024
JL Audio

JL Audio Stealthbox SB-GM-SLVCRW/10TW3 Handleiding

15 November 2024
JL Audio

JL Audio Stealthbox SB-T-TACDC12/10TW3 Handleiding

15 November 2024
JL Audio

JL Audio StowAway PES112-TW1 Handleiding

11 Juni 2024
JL Audio

JL Audio Fathom CTS-113-ST575-13TW5H Handleiding

10 Juni 2024
JL Audio

JL Audio Fathom CTS-213-TD900-13TW5H Handleiding

10 Juni 2024

Handleiding Subwoofer

Nieuwste handleidingen voor Subwoofer

Pioneer

Pioneer TS-A25S4 Handleiding

13 December 2024
Pioneer

Pioneer TS-A30S4 Handleiding

13 December 2024
Pioneer

Pioneer TS-A120S4E Handleiding

13 December 2024
JBL

JBL Power P1022 Handleiding

12 December 2024
JBL

JBL Power P1222 Handleiding

12 December 2024
ButtKicker

ButtKicker BK-LFE Handleiding

10 December 2024
Infinity

Infinity TSS-SUB750 Handleiding

9 December 2024
Infinity

Infinity TSS-SUB4000 Handleiding

9 December 2024
Infinity

Infinity Reference SUB R12 Handleiding

9 December 2024
AudioSource

AudioSource PSW110 Handleiding

9 December 2024