Jensen VX4025 Handleiding

Jensen Receiver VX4025

Lees hieronder de 📖 handleiding in het Nederlandse voor Jensen VX4025 (3 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 95 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

What’s in the Box

The following items are supplied

with the VX4025:

• VX402 HeadUnit5

• TrimRing

• HardwareBag

• Power/SpeakerOutputHarness

• RemoteControl

• ExternalMicrophone

• Installation Guide/ Quick Start

Tools and Supplies

The following tools and supplies

are needed to install the VX4025:

• Torx type, fl t-head and Philipsa

screwdrivers

• Wire cutters and strippers

• Tools to remove existing radio (screw

driver, socket wrench set or other

tools)

• Electrical tape

• Crimping tool

• Volt meter/test light

• Crimp connections

• 18 gauge wire for power connections

• 16 – 18 gauge speaker wire

WARNING!Neverinstallthisunitwhereoperationandviewingcouldinterferewith

safedrivingconditions.

VX4025

Installation / Quick Start Guide

Complete o m peration anual is

o nline at www.jensenmobile.com

Note: There is no operation manual in this package

Disconnect the Battery

• To prevent a short circuit, be sure to turn off the and remove the negative (-) battery cable prior to installation.ignition

NOTE: If VX402 is to be in a car with drive or the 5installed equipped an on-board navigation computer, do not

disconnect battery the disconnected, the computer the cable. If cable is memory may be these lost. Under conditions,

use extra caution avoid causing a short during installation to circuit.

Replacing the Fuse

• When replacing vehicles Radio always proper rated replacement fuse. Using improper ratingthe fuse use the a fuse with an

could damage the unit and cause a fi e.r

ISO-DIN Installation

The VX402 is designed to into a 2.0 DIN dashboard opening. The unit has threaded holes in the chassis side panels which may 5fit

be used with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to

mount the radio to the dashboard. Please consult with your local car stereo specialty shop for assistance on this type of

installation.

NOTE: It responsibility to install and operate manner accordance local, state and federal is end-users the this unit a in in with

laws. The PARKING BRAKE wire MUST BE CONNECTED as directed in the manual.

Using the Cosmetic Trim Ring

A cosmetic trim ring is supplied with the head unit for installation

flexibility. This unit will into most import dashes with little or fit

no to the dash board/cavity. Some US domestic modification

vehicle dashes will accept a Double-DIN chassis, but there is

usually a small gap between the radio and dash piece after

installation is complete. In this case, use the trim ring to conceal

any gaps that may be present.

1. Remove the existing factory radio from the dashboard or

center console mounting. Save all hardware and brackets as

they will be used to mount the new radio.

2. Remove the factory mounting brackets and hardware from the

existing radio and attach them to the new radio.

CAUTION! Do not exceed M5 X 6MM screw size. Longer

screws may damage components inside the chassis.

3. Place the radio in front of the dashboard opening so the

wiring can be brought through the mounting sleeve. Follow

the wiring diagram carefully and make certain all connections

are secure and insulated with wire nuts or electrical tape. After

completing the wiring connections, plug the connector into

the mating socket on the rear of the chassis. Turn the unit on

to operation (vehicle ignition switch must beconfirm “ON”). If

the unit does not operate, re-check all wiring until the problem

is corrected.

4. Mount the new radio assembly to dashboard or the center

console using the reverse procedure in step 1 above.

CAUTION! Be careful not to damage the car wiring.

NOTE: For proper operation of the CD/DVD player, the chassis must be mounted within 30° of horizontal. Make sure the

unit is mounted within this limitation.

S W C Readyteering heel ontrol (SWC)

The recommended Interface SWC is the PAC control adapter SWI-RC steering wheel .

SWI-RC installation hints:

1. . SSet "Radio Select Switch" et the SWI-RC to position 7 Pioneer/Sony/Other . - " "

2. Programming - U radio function for Jensen branded head units.se the Pioneer/Sony Other /mapping order

3. When programming the SWI-RC, if a function is not supported (or not desired), then the function be skipped as perMUST

the PAC SWI-RC instructions.

4. The SWC functions MUST also be programmed in the correct order per the PAC SWI-RC radio function mapping order

instructions.

B SiriusXMLACK DIN CABLE -

BLACK 1MM WIRE - BT ANTENNA

BLACK 3.5MM - BT MICROPHONE

YELLOW RCA - REAR CAMERA

SPEAKER (-)

SPEAKER (+)

PEAKER (-)

SPEAKER (+)

RIGHT FRONT SPEAKER (-)

RIGHT REAR SPEAKER (+)

RIGHT REAR SPEAKER (-)

LEFT REAR SPEAKER (+)

LEFT REAR SPEAKER (-)

BATTERY 12V (+)

GROUND (-)

ACC / IGNITION (+)

TFT DIMMER (+)

POWER ANT & AMP (+)

BRAKE (-)

REVERSE (+)

LEFT FRONT S

LEFT FRONT SPEAKER (+)

RIGHT FRONT

WHITE

WHITE/BLACK

GRAY

GRAY/BLACK

PURPLE

PURPLE/BLACK

GREEN

GREEN/BLACK

YELLOW

BLACK

RED

ORANGE

BLUE

PINK

GREEN/WHITE

SWC A

SWC B

WHITE/PURPLE

WHITE/BROWN

BROWN/BLACK SWC GND

Product specificaties

Merk:	Jensen
Categorie:	Receiver
Model:	VX4025
Kleur van het product:	Zwart
Breedte:	- mm
Diepte:	- mm
Hoogte:	- mm
Bluetooth:	Ja
Beeldscherm:	TFT
Connectiviteitstechnologie:	Bedraad en draadloos
Geïntegreerde geheugenkaartlezer:	Ja
Compatibele geheugenkaarten:	MicroSD (TransFlash)
Aantal USB-aansluitingen:	1
Soort optische drive:	DVD speler
Audio-uitgangskanalen:	- kanalen
Versterker:	Ja
Afstandsbediening inbegrepen:	Nee
Vermogen uitvoer per kanaal (20-20KHz@8 Ohm):	- W
Inclusief optische drive:	Ja