JennAir KUIX505EBS Handleiding

JennAir Niet gecategoriseerd KUIX505EBS

Lees hieronder de 📖 handleiding in het Nederlandse voor JennAir KUIX505EBS (24 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/24
ICE MAKER INSTALLATION INSTRUCTIONS
INSTRUCTIONS D’INSTALLATION DE
MACHINE À GLAÇONS
ICE MAKER SAFETY
Table of Contents/Table des matières
ICE MAKER SAFETY......................................................................1
INSTALLATION INSTRUCTIONS ..................................................2
Unpack the Ice Maker..................................................................2
Location Requirements................................................................2
Electrical Requirements ...............................................................3
Water Supply Requirements ........................................................3
Vacation or Extended Time Without Use.....................................3
Connect Water Supply.................................................................4
Drain Pump Installation ................................................................5
Drain Connection .........................................................................7
Door Reversal—Side Swing Only ................................................9
Leveling ......................................................................................11
Cleaning......................................................................................11
SÉCURITÉ DE LA MACHINE À GLAÇONS ................................13
INSTRUCTIONS D’INSTALLATION.............................................14
Déballage de la machine à glaçons ...........................................14
Exigences d’emplacement.........................................................14
Spécifications électriques ..........................................................15
Spécifications de l’alimentation en eau .....................................15
Vacances ou longue période d’inutilisation ...............................15
Raccordement à la canalisation d’eau.......................................15
Installation de la pompe de vidange ..........................................16
Raccordement au conduit vidange............................................19
Inversion du sens d’installation de la porte —
Porte à ouverture latérale uniquement.......................................20
Nivellement.................................................................................22
Nettoyage ...................................................................................23
W10761663A
You can be killed or seriously injured if you don't immediately
You can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
2
INSTALLATION INSTRUCTIONS
Unpack the Ice Maker
Removing Packaging Materials
Remove tape and glue from your ice maker before using.
■To remove any remaining tape or glue from the exterior of the
ice maker, rub the area briskly with your thumb. Tape or glue
residue can also be easily removed by rubbing a small
amount of liquid dish soap over the adhesive with your
fingers. Wipe with warm water and dry.
■Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. Do not
use chlorine bleach on the stainless steel surfaces of the ice
maker. These products can damage the surface of your
ice maker.
Cleaning Before Use
After you remove all of the packaging materials, clean the inside
of your ice maker before using it. See the cleaning instructions in
the “Ice Maker Care” section.
Location Requirements
■To ensure proper ventilation for your ice maker, the front side
must be completely unobstructed. The ice maker may be
closed-in on the top and three sides, but the installation
should allow the ice maker to be pulled forward for servicing
if necessary.
■Installation of the ice maker requires a cold water supply inlet
of ¹⁄₄" (6.35 mm) OD soft copper tubing with a shutoff valve or
a Whirlpool supply line Part Number 8212547RB, and a
Whirlpool approved drain pump, Part Number 1901A, only to
carry the water to an existing drain.
■Choose a well-ventilated area with temperatures above 55°F
(13°C) and below 110°F (43°C). Best results are obtained
between 70°F and 90°F (21ºC and 32°C).
■The ice maker must be installed in an area sheltered from the
elements, such as wind, rain, water spray, or drip.
■When installing the ice maker under a counter, follow the
recommended opening dimensions shown. Place electrical
and plumbing fixtures in the recommended location as
shown.
NOTES:
■Check that the power supply cord is not damaged or
pinched or kinked between the ice maker and the
cabinet.
■Check that the water supply line is not damaged or
pinched or kinked between the ice maker and the
cabinet.
■Check that the drain line (on some models) is not
damaged or pinched or kinked between the ice maker
and the cabinet.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
:
To reduce the risk of fire, electric shock, or injury when using your ice maker, follow these basic
precautions
:
SAVE THESE INSTRUCTIONS
■Plug into a grounded 3 prong outlet.
■Do not remove ground prong.
■Do not use an adapter.
■Do not use an extension cord.
■Disconnect power before manually cleaning the inside components.
■Disconnect power before servicing.
■Replace all parts and panels before operating.
■Use two or more people to move and install ice maker.
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.
WARNING
Excessive Weight Hazard
Use two or more people to move and install ice maker.
Failure to do so can result in back or other injury.
3
■Check that the ice maker door is not flush with the
standard cabinets to avoid problems with opening the ice
maker door.
■Choose a location where the floor is even. It is important for
the ice maker to be level in order to work properly. If needed,
you can adjust the height of the ice maker by changing the
height of the leveling legs. See “Leveling.”
Electrical Requirements
Before you move your ice maker into its final location, it is
important to make sure you have the proper electrical
connection:
A 115 volt, 60 Hz., AC only, 15- or 20-amp electrical supply,
properly grounded in accordance with the National Electrical
Code and local codes and ordinances, is required.
It is recommended that a separate circuit, serving only your ice
maker, be provided. Use a receptacle which cannot be turned off
by a switch or pull chain.
IMPORTANT: If this product is connected to a GFCI (Ground
Fault Circuit Interrupter) equipped outlet, nuisance tripping of the
power supply may occur, resulting in loss of cooling. Ice quality
may be affected. If nuisance tripping has occurred, and if the
condition of the ice appears poor, dispose of it.
Recommended Grounding Method
The ice maker must be grounded. The ice maker is equipped with
a power supply cord having a 3 prong grounding plug. The cord
must be plugged into a mating, 3 prong, grounding-type wall
receptacle, grounded in accordance with the National Electrical
Code and local codes and ordinances. If a mating wall receptacle
is not available, it is the personal responsibility of the customer to
have a properly grounded, 3 prong wall receptacle installed by a
qualified electrician.
Water Supply Requirements
Check that the water supply lines are insulated against freezing
conditions. Ice formations in the supply lines can increase water
pressure and damage your ice maker or home. Damage from
frozen supply lines is not covered by the warranty.
A cold water supply with water pressure of between 30 and
120 psi (207 and 827 kPa) is required to operate the ice maker. If
you have questions about your water pressure, call a licensed,
qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT:
■A reverse osmosis water filtration system is not
recommended for ice makers that have a drain pump
installed.
■For gravity drain systems only.
■The pressure of the water supply coming out of a reverse
osmosis system going to the water inlet valve of the ice
maker needs to be between 30 and 120 psi (207 and
827 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
NOTE: The reverse osmosis system must provide 1 gal. (3.8 L) of
water per hour to the ice maker for proper ice maker operation. If
a reverse osmosis system is desired, only a whole-house
capacity reverse osmosis system, capable of maintaining the
steady water supply required by the ice maker, is recommended.
Faucet capacity reverse osmosis systems are not able to
maintain the steady water supply required by the ice maker.
If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 to 414 kPa):
■Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
■Allow the storage tank on the reverse osmosis system to refill
after heavy usage.
If you have questions about your water pressure, call a licensed,
qualified plumber.
Vacation or Extended Time Without Use
■When you will not be using the ice maker for an extended
period of time, turn off the water and power supply to the ice
maker.
■Check that the water supply lines are insulated against
freezing conditions. Ice formations in the supply lines can
increase water pressure and cause damage to your ice maker
or home. Damage from freezing is not covered by the
warranty.
A. Recommended location for electrical and plumbing fixtures
B. Floor level
3¹⁄₂"
(8.9 cm)
9"
(22.9 cm)
11 "¹⁄₂
(29.2 cm)
24"
(60.1 cm)
34"
(86.4 cm)
Min.
34 "¹⁄₂
(87.6 cm)
Max.
B
A
28 "¹⁄₂
(72.4 cm)
C
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING

Product specificaties

Merk: JennAir
Categorie: Niet gecategoriseerd
Model: KUIX505EBS

Heb je hulp nodig?

Als je hulp nodig hebt met JennAir KUIX505EBS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd JennAir

JennAir

JennAir KDAS104HSS Handleiding

8 Juli 2023
JennAir

JennAir TC607X Handleiding

7 Juli 2023
JennAir

JennAir WFG525S0JV Handleiding

23 Juni 2023
JennAir

JennAir MKC2150AS Handleiding

20 Juni 2023
JennAir

JennAir JEA8120ADW Handleiding

19 Juni 2023
JennAir

JennAir UDT518SAHP Handleiding

18 Juni 2023
JennAir

JennAir KUIX505EBS Handleiding

18 Juni 2023
JennAir

JennAir TC707S Handleiding

18 Juni 2023
JennAir

JennAir JXI8536DS Handleiding

18 Juni 2023
JennAir

JennAir CAVIAR30L Handleiding

18 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

MSW

MSW -HRH-600 Handleiding

5 November 2024
MSW

MSW -PCJ-302 Handleiding

5 November 2024
MSW

MSW -ETT-22 Handleiding

5 November 2024
DoorBird

DoorBird MTM56A Handleiding

5 November 2024
Hacienda

Hacienda PWB801 Handleiding

5 November 2024
Hacienda

Hacienda PWB802 Handleiding

5 November 2024
MSW

MSW -ECF1-01 Handleiding

5 November 2024
MSW

MSW -MWC-01 Handleiding

5 November 2024
MSW

MSW -TM01 Handleiding

5 November 2024
Singercon

Singercon CON.DJB01 Handleiding

5 November 2024