Irritrol 700DK-1-MF Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Irritrol 700DK-1-MF (7 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 251 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/7
®
Drip Zone Valve Kits
Installation Instructions
Click on the links to view the documents.
Drip Zone Valve Kit
Models 2500DK-1-LF and 2500DK-1-MF
Installation Instructions
373-0512 Revision B
Drip Zone Valve Kit
Models 2711APRDK-LF and 2711APRDK-MF
Installation Instructions
373-0513 Revision B
Drip Zone Valve Kit
Models 2713APRDK-LF and 2713APRDK-MF
Installation Instructions
373-0514 Revision B
Drip Zone Valve Kit
Models 700DK-075-LF
Installation Instructions
373-0515 Revision B
Drip Zone Valve Kit
Models 700DK-1-LF and 700DK-1-MF
Installation Instructions
373-0516 Revision B
Drip Zone Kit - Less Valve
Models DK-LV-LF and DK-LV-MF
Installation Instructions
373-0535 Revision A
®
Get more doneTM
Drip Zone Valve Kit
Models 2500DK-1-LF and 2500DK-1-MF
Installation Instructions
Kit Components
• Irritrol 2500 Series Valve, Model 2500TF
• Pressure Regulator - 25 psi at 0.1–8 GPM,
3/4" Female NPT (Low Flow [LF] model)
• Pressure Regulator - 25 psi at 2–20 GPM,
3/4" Female NPT (Medium Flow [MF] model)
• 3/4" MPT x MPT F Series Y-filter, 150 Mesh Screen
• Drip Line Compression Adapter, CA-710
• 1" x 3/4" Male NPT Reducer Bushing
• 3/4" MPT x 1/2" Slip Fitting
Specifications
• Downstream Pressure Regulation: 25 psi
• Flow Rate at 25 psi: (LF Model) 0.1–8 GPM
(MF Model) 2–20 GPM
• Filtration: 150 Mesh Stainless Steel Screen
• 1" In-line Electric Control Valve, Model 2500TF
Operating Pressure: 10–150 psis
24 VAC, 50/60 Hz Solenoids
Inrush: 0.40 amp, 9.6 VA s
Holding: 0.20 amp, 4.8 VA s
Manual On/Off - Internal and External Bleeds
Adjustable Flow Controls
Installation Procedure
CAUTION: When assembling the drip zone valve kit components, use just 1 ½ to 2 turns of PTFE tape on male
threads. Never use pipe dope. To achieve a leak-free thread connection, turn the male fitting until it is finger-
tight, and then add one or two more turns. Over-tightening can cause splitting and failure of the female threads.
Important: Ensure the Y-filter, control valve and pressure regulator are installed in the correct flow
orientation. Flow direction arrows are provided on each component. Refer to Figure 1.
1. Thread the Y-filter inlet into the valve outlet with
the provided 1" x 3/4" NPT reducer bushing. Use
PTFE tape on all threaded connections. Angle the
Y-filter slightly downward as shown in Figure 1.
2. Thread the pressure regulator inlet into the Y-filter
outlet.
3. Connect the water source supply line and piping
to drip emitters.
NOTE: Installing the valve assembly below grade
in a valve box is recommended for protection and
ease of service.
NOTE: Refer to the 2500TF Series Valve
Instruction Guide provided in the kit for complete
valve installation and operation information.
NOTE: To adapt the Drip Zone Valve Kit for
dripline applications, install the provided 3/4" MPT
x 1/2" Slip fitting and CA-710 dripline compression
adapter to the pressure regulator outlet.
4. Flush the system to remove debris.
5. To determine the recommended minimum/
maximum number of drip emitters per control
valve, refer to the table below.
2500TF Series Valve
Valve Box
Reducer
Bushing
Y-filter
Pressure
Regulator
3/4" MPT x
1/2" Slip
Compression Adapter
(Use with Flex Tube only)
To Emitters From Source
Figure 1
Table 1
© Irritrol • www.irritrol.com • For Technical Assistance, call 1-800-333-3125 Part Number 373-0512 revision B
®
Get more doneTM
Drip Zone Valve Kit
Models 2711APRDK-LF and 2711APRDK-MF
Installation Instructions
Kit Components
• Irritrol 2700 Series Valve, Model 2711APR
• Pressure Regulator - 25 psi at 0.1–8 GPM,
3/4" Female NPT (Low Flow [LF] model)
• Pressure Regulator - 25 psi at 2–20 GPM,
3/4" Female NPT (Medium Flow [MF] model)
• 3/4" MPT x MPT F Series Y-filter, 150 Mesh Screen
• Drip Line Compression Adapter, CA-710
• 3/4" MPT x 1/2" Slip Fitting
Specifications
• Downstream Pressure Regulation: 25 psi
• Flow Rate at 25 psi: (LF Model) 0.1–8 GPM
(MF Model) 2–20 GPM
• Filtration: 150 Mesh Stainless Steel Screen
• 3/4" Anti-siphon Electric Control Valve, Model 2711APR
Operating Pressure: 10–150 psis
24 VAC, 50/60 Hz Solenoids
Inrush: 0.40 amp, 9.6 VA s
Holding: 0.20 amp, 4.8 VA s
Manual On/Off - Internal and External Bleeds
Adjustable Flow Controls
Installation Procedure
CAUTION: When assembling the drip zone valve kit components, use just 1 ½ to 2 turns of PTFE tape on male
threads. Never use pipe dope. To achieve a leak-free thread connection, turn the male fitting until it is finger-
tight, and then add one or two more turns. Over-tightening can cause splitting and failure of the female threads.
Important: Ensure the Y-filter, control valve and pressure regulator are installed in the correct flow
orientation. Flow direction arrows are provided on each component. Refer to Figure 1.
1. Thread the Y-filter inlet into the valve outlet. Use
PTFE tape on all threaded connections. Angle the
Y-filter slightly downward as shown in Figure 1.
2. Thread the pressure regulator inlet into the Y-filter
outlet.
3. Connect the water source supply line and piping
to drip emitters.
NOTE: Refer to the 2711APR Series Valve
Instruction Guide provided in the kit for complete
valve installation and operation information.
NOTE: To adapt the Drip Zone Valve Kit for
dripline applications, install the provided 3/4" MPT
x 1/2" Slip fitting and CA-710 dripline compression
adapter to the pressure regulator outlet.
4. Flush the system to remove debris.
5. To determine the recommended minimum/
maximum number of drip emitters per control
valve, refer to the table below.
2711APR
Valve
NOTE: The valve must be
installed at least 6" above the
highest emitter it controls.
Y-filter
Pressure
Regulator
3/4" MPT x 1/2" Slip
Compression Adapter
(Use with Flex Tube only)
To Emitters
From Source
Figure 1
Table 1
© Irritrol • www.irritrol.com • For Technical Assistance, call 1-800-333-3125 Part Number 373-0513 revision B


Product specificaties

Merk: Irritrol
Categorie: Niet gecategoriseerd
Model: 700DK-1-MF

Heb je hulp nodig?

Als je hulp nodig hebt met Irritrol 700DK-1-MF stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Irritrol

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd