Intermatic T30604R Handleiding

Intermatic Niet gecategoriseerd T30604R

Lees hieronder de 📖 handleiding in het Nederlandse voor Intermatic T30604R (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 6 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Many of today’s energy efficient pools and spas utilize the benefits of the two stage water circulation

principal. For example, while the daily cleaning process requires high pressure and fast turnover of

a large amount of water in the morning, the heating,

either by the sun or a heater, is more energy efficient

on a slower flow rate during the day. Also, some of

the new water sanitation techniques require longer

dispensing time of ozone or chemicals.

The most economical way to operate a pool or spa

is by the use of a two speed filter pump, together

with this reliable, simple to install, simple to operate

Two Speed Pump Control.

This Control is designed to automatically operate

a two speed pump on a daily schedule. The

all-weather enclosure contains two heavy duty,

industrial grade time switches. In addition, the

enclosure has a provision to install switches or a

GFCI receptacle on the side as well as inside the

enclosure. The time switch on the right is intended

for starting and stopping the pump and the time

switch on the left is for changing the speed (RPM)

of the pump while it is running. The mechanism on

the right can also accommodate an optional heater

control (Fireman) switch.

Model: T30604R

TIME CONTROL FOR TWO SPEED POOL/SPA FILTER PUMPS FOR INDOOR/OUTDOOR USE

ELECTRICAL RATING: 5 H.P. Max. - 240 Volt - 60 Hz.

Maximum running load not to exceed 28 Amperes.

Suitable for Pool Equipment Control and for Direct Conduit Connection to a

Wet-Niche or No-Niche Underwater Luminaire

DANGER! TO AVOID RISK OF INJURY:

...do not permit children to operate the Control Unit or use the Pool/Spa unless they are closely supervised at all times.

...test GROUND FAULT protection regularly. If it fails to reset, DO NOT USE THE POOL or SPA!

Contact a qualified service technician.

...always disconnect electricity before servicing this control or the equipment connected to it. THIS CONTROL IS NOT TO BE

USED AS A POWER DISCONNECT.

READ, FOLLOW AND SAVE THIS INSTRUCTION MANUAL

GENERAL INFORMATION

IMPORTANT SAFETY INSTRUCTIONS

When installing and operating this electrical control and other associated equipment, basic safety precautions should always be followed,

including the following:

1. Read and follow all instructions.

2. This Control must be installed by a qualified electrician, according to National and Local Electrical Codes.

3. Install this control not less than 5 feet (3 meters in Canada) from inside edge of pool. USE COPPER CONDUCTORS ONLY.

4. Do not exceed the maximum ratings of individual components, wiring devices, and current carrying capacity of conductors.

5. For grounding and bonding this Control and the installation, refer to Article 680 of the National Electrical Code.

6. The Control should not operate any equipment which would cause bodily injury or property damage should it be activated unexpectedly.

READ, FOLLOW AND SAVE THIS INSTRUCTION MANUAL

T30604R SERIES

POOL/SPA EQUIPMENT CONTROLS

INSTALLATION

OPERATION &

SERVICE MANUAL

INSTALLATION

1. Remove the four #10 hex head screws from the

back of the enclosure and attach mounting brackets

to enclosure.

2. Select the proper location for the Control and hang

enclosure on a flat vertical surface or other support,

using hardware suitable for the purpose.

3. Prepare the necessary conduit runs, terminate them

at both ends and pull-in the conductors as specified

by the installation layout.

*If this control is used for direct conduit connection

to a wet niche or no niche luminaire, order one of

the following: 156PA13713A for a 1/2” non-metallic

kit, 156PA13714A for a 3/4” non-metallic kit,

156PA13715A for a 1” non-metallic kit, or

156PA14336A for a 1/2” metallic kit.

4. Refer to Figure 1 below. Note that this enclosure

contains two independent time switches. The one on

the left is a , a Single Pole DoubleModel T106M

 Throw(SPDT)switch,andit’sfunctionistochange

the speed (RPM) of the pump motor. The time

switch on the right is a , a DoubleModel T104M

 PoleSingleThrow(DPST)switch,andit’s

function is to the start/stop

pump motor. To wire the

two switches, follow wiring

diagram on page 4 of this

manual. Make sure that

connections to time switch terminals are tight

(25 lb. - in. minimum) and insulation clears the

pressure plate - see illustration.

a. Remove clock motor leads from Terminals A and 3 of

T106M .and connect to Terminals 1 and 3 of T104M

Connect LINE 1 to and L to Terminal 1 INE 2 Terminal 3

of T104M.

b. Install jumpers between Terminals 1 and 4 of T106M

and between and Terminal 2 of T104M Terminal 1 of

T106M.

c. Connect COMMON of Two Speed Pump to Terminal 4

of T104M Terminal 2 of T106M, LOW to and HIGH to

Terminal 3 of T106M.

d. Connect green grounding conductors to the Equipment

Grounding Terminal at bottom of enclosure.

5. If required by the heater manufacturer, install

fireman switch kit 156T4042A (not furnished) on

Time Switch Plate and make the fireman switch

connections.

Use at least #18

AWG wiring with

insulation rated

300 Volt or higher.

Place heater

ON/OFF switch

on heater to ON.

6. To install additional wiring devices inside the

enclosure, first remove rectangular knock-out(s) in

dead front. Next, remove hex head screws in back of

enclosure and install stand-offs* in place of screws.

Attach wiring device to stand-offs.

• Stand-offs are not furnished. Order 21T156A for a set of

four (4) stand-offs and mounting hardware.

7. If external bonding is required, install bonding lug(s)

on bottom of enclosure (156T11047A may be

ordered) and bond installation according to code

requirements.

8. Testing of the installation is optional and

recommended only if pump is securely in place

and will not be damaged by the following test:

a. Turn the manual level of the time switches to OFF.

b. Turn ON power at breaker panel.

c. Move the manual lever of T104M to the right (ON).

Pump should start and run on low speed.

d. Move the manual lever of T106M to the right (ON).

Pump should now be running on high speed.

e. Move the manual lever of T104M to the left (OFF).

Pump should stop running.

In case of unsatisfactory results, turn OFF power,

check your wiring, refer to Troubleshooting on Page 4.

9. Install front panel over wiring compartment.

The control is now ready for programming,

Keep door closed at all times.

Figure 1

PRESSURE PLATE

TERMINAL SCREW

MAKE SURE INSULATION

CLEARS PRESSURE PLATE

WARNING: Do not disconnect high limit or pressure switches.

OPERATION

EXAMPLES

TO SET DAILY SCHEDULE: The setting of a schedule

is done by placing the ON (silver) and OFF (gold) trip-

pers on the two yellow dials.

The dials turn in synchronous speed and make exactly

one revolution in 24 hours. The trippers placed on the

dial on the right will set the time of pump start and stop

operation while the

trippers on the left side dial will set the time

the pump will speed.change

The length of the daily filtration/heating cycle depends

on many variables such as geographic location, size

and usage of pool, season of year,

type of pool equipment, etc. If not sure, contact your

local pool service professional for advice.

Setting a schedule is easy:

1. Set Time of Day on both time switches by

pulling out, then turning yellow dials until

Time-Of-Day lines up with pointer.

2. Set Start (ON tripper) and Stop (OFF tripper)

times on right side (T104M) dial.

3. Set Low to High (ON tripper) time and

High to Low (OFF tripper) time on left side

(T106M) dial.

WARRANTY

If within one (1) year from the date of installation, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair

or replace it free of charge.

The warranty does not cover labor for removal or reinstallation and does not apply to: (a) damage caused by accident, abuse, mishandling, or drop-

ping; (b) a unit which has been subject to unauthorized repair; (c) units not used in accordance with directions; (d) damages exceeding the cost of the

product. Some states do not allow a limitation of damages so the foregoing warranty may not apply to you. This warranty gives you specific legal rights

and you may also have other rights which vary from state to state.

This warranty service is available, if the defective product or its defective component is returned with proof of purchase and date of installation,

either (a) to the dealer from whom the unit was purchased or (b) by shipping prepaid to the Intermatic Service Center, Intermatic Incorporated, Intermatic

Plaza, Spring Grove IL 60081-9698