Intermatic ST01 Handleiding

Intermatic Schakelaar ST01

Lees hieronder de 📖 handleiding in het Nederlandse voor Intermatic ST01 (2 pagina's) in de categorie Schakelaar. Deze handleiding was nuttig voor 65 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Connect the GREEN wire to the grounding screw in the box. If

a plastic box, connect to ground as supplied.

Make sure all twist connectors are tight.

If a 3-Way Switch Setup:

NOTE: The distance between

switch timer and remote switch

must not exceed 100 feet.

Locate the COMMON

wire connected to ﬁrst old

switch. It might be attached

to a different colored screw,

or ﬁnd markings on old switch.

Connect BLACK wire from switch timer to COMMON wire,

using a twist connector.

Connect the other two wires from the old switch to the Blue

and RED wires from the switch timer.

Connect the GREEN wire to the grounding screw in the box. If

a plastic box, connect to ground as supplied.

Using diagram #1 below. Identify and remove wire “C” from

the “Common” terminal of your existing remote switch.

Using diagram # 2 below, remove and reconnect wires “B”

and “C” to the “Common” terminal of your remote switch,

using the supplied piece of jumper wire, if necessary. Follow

diagram # 3 below, if using a new single-pole remote switch.

NOTE: For new construction or to replace a dimmer switch,

a lighted switch, or a 3-way switch without screw terminals,

a single-pole switch can be used at the remote location, as

shown.

NOTE: If the building’s wiring colors don’t allow you to tell

wire “A” from “B,” just pick one of the two wires and connect

as if it is wire “B.” After the installation is complete, if the con-

trolled light or device will not turn on properly, simply reverse

wires “A” and “B.” See Steps J and K for how to check.

Tuck wires into the timer wall box leaving room for the timer.

Using screws provided, mount the switch timer into the wall

box, then install the wall plate.

Install the remote 3-way switch in its box and install wall

plate. Turn the power back on at the service panel.

Make sure the switch timer displays “MAN” mode. Do the fol-

lowing test with the remote switch in each of its 2 positions:

Press the ON/OFF button on the switch timer several times.

Each time that you push the ON/OFF button, the switch timer

should “click” and the controlled light or device (the “load”)

should turn on or off. If so, proceed to Step K.

If the timer clicks but the load does not operate, re-check

your wiring and make sure the load is functional.

Self-Adjusting Wall Switch Timer

Turn off power at the service panel by REMOVING FUSE or

TURNING THE CIRCUIT BREAKER OFF.

Remove the existing wall switch.

Trim building wires to 7/16” as shown.

If a Single Switch Setup:

Connect one of the two wires

from the wall to the black wire

from the switch timer, using

the twist connectors provided.

Connect the other wire from

the wall to the blue wire from

the switch timer, using the

twist connectors provided.

NOTE: The RED wire is not used in single-switch installations.

Cap with a twist connector.

Resistive (heater) 15 Amp, 120-277 VAC

Tungsten (incandescent) 15 Amp @ 120 VAC, 6 Amp @ 208-277 VAC

Ballast (ﬂuorescent) 8 Amp @ 120 VAC, 4 Amp @ 208-277 VAC

Motors 1 H.P. @ 120 VAC, 2 H.P. @ 240 VAC

DC Loads 4 Amp @ 12 VDC, 2 Amp @ 28 VDC

•

Installation and User Instructions

MODEL ST01 Series

2 – Install the Switch Timer

Ratings

Before installing the switch timer into the wall, make sure the

supplied battery is installed and working.

Open the access door to reveal the battery tray, located below

the ON/OFF keypad.

If there is a pull tab at the battery tray, remove the tab to con-

nect the installed battery. Make sure battery tray is pushed

fully into place. Proceed to Step 6.

If the battery was supplied loose, use a ﬂat screwdriver to pry

loose the battery tray.

Place the supplied “CR2” battery into the tray, observing +

and – markings on tray.

Replace the battery tray into the switch timer.

The display will initialize itself then ﬂash “12:00 AM” in

MANual mode.

Press the ON/OFF button. The switch timer should “click.”

NOTE: If display doesn’t ﬂash “12:00 am”, the battery may be

dead. Replace the battery before installing the switch timer.

1 – Before Installing Switch Timer, Install and Check Battery

BLACK WIRE

BLUE WIRE

RED WIRE

(capped, not connected)

RED WIRE

BLUE WIRE

BLACK WIRE

WIRE FROM

“COMMON” OF

OLD SWITCH

7/16”

DIAGRAM 1:

TYPICAL

EXISTING

2-SWITCH

SETUP

LOAD

NEUTRAL

3-WAY

MAIN SWITCH

WIRE “A”

“COMMON” TERMINAL

LINE

3-WAY

REMOTE SWITCH

WIRE “B”

WIRE “C”

DIAGRAM 2:

2-SWITCH SETUP,

TIMER INSTALL

RE-USING EXISTING

REMOTE 3-WAY SWITCH

LOAD

NEUTRAL

WIRE “A”

“COMMON” TERMINAL

LINE

3-WAY

REMOTE SWITCH

WIRE “B”

NOT USED

BLACK

TIMER

BLUE

RED

WIRE “C”

JUMPER

DIAGRAM 3:

2-SWITCH SETUP,

TIMER INSTALL USING

NEW SINGLE-POLE

REMOTE SWITCH

LOAD

NEUTRAL

WIRE “A”

LINE

SINGLE-POLE

REMOTE SWITCH

WIRE “B”

BLACK

TIMER

BLUE

RED

WIRE “C”

JUMPER

158ST13133

Observed Problem Possible Cause What to Do

Switch timer does not switch ON/OFF but

display looks normal.

Switch timer is not set in AUTO, RANDom, or

MANual mode.

Press MODE to select the operational mode you

want to use.

Switch timer won’t enter AUTO or

RANDom mode when you press MODE.

The time of day or timer settings have not

been set.

Make sure the time of day and at least one sched-

uled activity have been set.

Switch timer switches at incorrect times

or skips some of the programmed times.

Programmed schedule(s) are incorrect. Press ON/OFF to review the settings and revise

them as necessary. See instructions at the left.

Switch timer is in RANDom mode, which var-

ies switching times up to ±20 minutes (to give

your home a “lived-in” look).

If you don’t want to keep the switch timer in

RANDom mode, press MODE to change to AUTO

mode.

The Astronomic and Speciﬁc switching times

are in conﬂict. For example, you’ve set ON to

DUSK and OFF at 8 pm, and due to seasonal

changes, DUSK has advanced to 8:30 pm.

NOTE: Your switch timer automatically skips

any conﬂicting ON event as summer ap-

proaches to prevent unwanted operation of

lights or other controlled devices. See “What

to Do” if you want to identify and remove

conﬂicting settings.

Complete the steps for setting the Time and

Date, then temporarily change the date to

June 21st.

Review the DAWN and DUSK settings by

pushing the ON/OFF button.

Make sure the speciﬁc ON or OFF time set-

tings won’t interfere with these DAWN and

DUSK times. Make changes as necessary.

When ﬁnished, change the Date setting back

to today’s date.

The lights or controlled devices don’t

match the programmed ON/OFF status

immediately after setting the time or

programming a schedule.

Switch timer does not “catch up” automati-

cally to the programmed load state. The status

of the switch timer will remain as is until it

comes to the next programmed ON/OFF time.

After entering your schedules or the time, then

returning to the AUTO mode, push the ON/OFF but-

ton to change the load state if necessary.

Load only operates when the remote

(3-way) switch is in one position, or the

switch timer ignores the remote switch.

The remote switch is wired incorrectly.

Recheck the wiring, especially for the jumper,

according to “If a 3-way Switch Timer” and “If a

Multiple Switch Timer Setup.”

The switch timer ignores a 3-way remote

switch even though it is wired correctly.

There is an excessive length of wire (more

than 100 feet), or there is buried wire to the

switch.

Eliminate the condition: either replace the buried

cable, do without the remote switch, or contact

Intermatic Customer Service for more options.

The remote switch is not functioning properly

or worn out. Replace the remote switch.

The load turns off immediately after being

turned on.

The remote switch or switch timer is wired

wrong.

There is an excessive length of wire

(greater than 100 feet)

There is buried wire to the remote switch.

The switch timer is not functioning properly.

•

If the problem persists with the switch timer’s red

wire disconnected or with a remote switch tempo-

rarily connected right at the switch timer, replace

the non-functioning switch timer. Otherwise, try

the above suggestions.

The battery tray is difﬁcult to replace.

Battery is not seated in the tray.

The tray is misaligned.

The contact tabs of the tray are bent.

•

Seat the battery in the tray, then reinstall.

The switch timer operation is sluggish or

not switching ON/OFF at all.

Though the “BATT” message is not being

displayed, the battery is getting weak.

Replace the battery. To test the battery, press the

ON/OFF button. The timer should “click.”

Timer shows ON but the light or other

controlled device is OFF.

The light or controlled device itself may be

switched OFF.

Make sure the light or controlled device is

switched ON and plugged in.

Troubleshooting Guide

LIMITED ONE-YEAR WARRANTY

If within one (1) year from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of charge. This warranty is

extended to the original household purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or any negligent use;

(b) units which have been subject to unauthorized repair, opened, taken apart or otherwise modiﬁed; (c) units not used in accordance with instructions; (d) damages exceeding the cost of the product; (e) sealed

lamps and/or lamp bulbs, LED’s and batteries; (f) the ﬁnish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear; (g) transit damage, initial installation costs,

removal costs, or reinstallation costs.

INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL

DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE

WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF

THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY TO

YOU.

This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product, along with proof of purchase, postage prepaid to the authorized

service center listed below. This warranty is made by: Intermatic Incorporated/After Sales Service/7777 Winn Rd., Spring Grove, Illinois 60081-9698/815-675-7000 http://www.intermatic.com Please be sure to wrap

the product securely to avoid shipping damage.

INTERMATIC INCORPORATED

SPRING GROVE, ILLINOIS 60081-9698

Electrical shock hazard. Risk of injury or death. Remove electrical power

at service panel before installing.

Risk of ﬁre or burns from used battery. Do not recharge, disassemble, heat

above 100˚ C, crush, or incinerate the lithium battery. Keep battery out of

reach of children. Replace only with Panasonic type CR2 or equivalent

CR2 battery approved by Underwriters Laboratories (UL). Use of a differ-

ent battery type may present a risk of ﬁre or explosion upon disposal of

battery.

Risk of ﬁre. Do not use timer to control devices that could have danger-

ous consequences due to inaccurate timing, such as sun lamps, sauna,

heaters, crock pots, etc.

•

WARNING

Follow local electrical codes during installation.

Risk of timer damage due to leakage if weak battery is not replaced promptly.

Dispose of used battery promptly per local regulations.

•

NOTICE

See ez set instrucons and wiring lustraons: il

hp://waterheatermer.org/ST01C-program.html

hp://waterheatermer.org/Intermac-mers-and-manuals.html#ST01C

6 – Set Initial Pair of ON and OFF Times

You have many options with up to 40 timer settings:

Set to a speciﬁc ON/OFF time.

Set to DAWN and DUSK, which automatically adjust as the

seasons change. This is the ASTRONOMIC feature.

Set to activate ALL days, M-F, WeeKenD, or individual days.

Programs are created in two procedures: setting an ON time fol-

lowed by setting an OFF time. You must set each time separately.

The instructions below will guide you as follows:

First, for setting an ON time, which can be DAWN or DUSK,

or a speciﬁc time such as 6:00 pm,

Then for setting an OFF time which can also be DAWN or

Dusk, or a speciﬁc time.

Press MODE until the screen displays ProGraM

below the time of day (Fig. 13).

•

As you use the menus to program, it will be helpful to have an

overview of how they are organized. Press the MODE button to

rotate through the switch timer’s modes: SET UP, PROGRAM,

AUTO, RANDOM, and MANUAL. All menus “loop”, so they

repeat when you get to the end. AUTO and RANDOM modes

are skipped until there is at least one ON/OFF setting.

Once you reach a Mode you want to work with, press the ON/

OFF button to rotate through the loop of settings available for

that Mode, returning to the beginning. For example, in SET UP

mode, you will see HOUR, MINute, AM/PM, Year, MONth, etc.

Use the + or – buttons to change a setting when it is FLASH-

ING (e.g., the correct hour). Holding the button makes the

numbers scroll faster. Pressing ON/OFF again advances to the

next setting and automatically saves — whether you changed

the setting or not. Saving is automatic, there’s no extra step.

If you’re interrupted during programming, your work to that

point is automatically saved after 5 minutes.

Press MODE when you’re ﬁnished to navigate to the mode you

want to operate the switch timer: Auto, Manual, or Random.

•

3 – Intro to Programming: Read Before You Begin

5 – Set the Date and Time

Fig. 8

Fig. 10

South

North

Center

North

Center

South

It’s unlikely that the new switch timer has any existing program-

ming but to make sure, use this procedure before setting the time.

Open the front cover.

Hold down ON/OFF.

Using a pen or paper clip, press and release RESET, which is

the small round button to the lower right of the + button.

When the screen displays INIT, release ON/OFF. The screen will

initialize, then ﬂash “12:00 am” in MANual mode.

All previous settings are now deleted.

4 – Clear Any Existing Programming

In order for the Astronomic Feature and automatic Daylight Sav-

ing Time settings to function properly, the CALENDAR settings

must be entered correctly.

WHAT IT MEANS: The icon of the LIGHT BULB indicates whether

the switch timer is ON or OFF. The WHITE area of the example

screens is what will be ﬂashing on your switch timer.

Press MODE until the screen displays SET UP.

The ﬁrst time, the hours/minutes display will

be ﬂashing (Fig. 4).

Press ON/OFF to display HOUR (Fig. 5), then

press + until the correct hour and AM/PM are

shown.

NOTE: If you go too far, press the - button to

back up, or press + until you loop back.

Press ON/OFF to display MIN ( Fig. 6), then

press + until the correct minute is shown.

Repeat this routine for YEAR, MONTH, DATE.

Verify that the day of the week is correct

(Fig. 7). If wrong, press + or – to loop back,

then reset the calendar information.

Press ON/OFF to display DST (Fig. 8), and set

whether you want to adjust automatically for

Daylight Saving Time (DST).

If you use DST, press + for AUTO.

If you do not use DST, press + for MANual.

Press ON/OFF to set your

ZONE (Fig. 9). This feature

tracks changes in sunrise

and sunset times. Press +

to select your local zone:

NoRTH, CENTer, or SOUth

(Fig. 10).

You can set DAWN or

DUSK to your exact time

in your area according to your newspaper or online. Use the

following procedures to do so, or press ON/OFF 3 times to skip.

Press ON/OFF to set your exact local time

for DAWN (Fig 11), then press + to set the

correct HOUR.

Press ON/OFF to display MIN (Fig. 12), then

press + until the correct minute is shown.

Repeat Steps a and b to set exact local time

for DUSK.

Press ON/OFF again and you’ll loop back to SET UP.

CHECK YOUR SETTINGS: Press ON/OFF repeatedly to loop back

around to review your date and time settings. If anything is

wrong, make corrections using the above steps.

The single lithium CR2 battery operates the ON/OFF function

(“click-click”) and maintains time of day and date. The screen

ﬂashes “BATT” when the battery is getting low.

The battery may be changed without removing AC power.

You have about one minute to swap batteries before the

switch timer “forgets” the date and time settings. Afterwards,

if the display is wrong or ﬂashes “12:00 AM”, reset the time

and date. All other settings (your ON/OFF programming)

remain in memory indeﬁnitely without battery or AC power.

To test the battery, press the ON/OFF button. The timer should

“click.”

Replace the battery per Section 1 Instructions as soon as pos-

sible after the low “BATT” message appears.

Do not leave exhausted battery in Switch Timer. (Risk of leakage.)

Replace only with Panasonic Type CR2 lithium battery or equiv-

alent CR2 battery approved by Underwriters Laboratories (UL).

Dispose of the used battery promptly according to local regu-

lations. Keep battery away from children. Do not disassemble

and do not dispose of battery in ﬁre.

•

About the Battery

Once set up, you have three choices for using the switch timer.

To make a selection, open the front cover and press the MODE

button until you see your choice of the following options:

AUTO — uses the timer settings you have programmed.

RANDom — gives your home a “lived-in” look by varying

your settings by a random amount of ± 20 minutes or so.

MANual — makes the switch into a standard ON/OFF switch

without timer settings. Press on the door of the switch timer

for ON, press again for OFF.

•

7 – Selecting AUTO, RANDom, or MANual Operation

Changing Program Times

Deleting an ON or OFF Setting

Use these steps to delete an existing ON or OFF setting that you

no longer want (for example, special settings from a vacation.)

Press MODE until the screen displays ProGraM

below the time of day (Fig. 24).

Press ON/OFF to display the program number,

then press the + button until you see the pro-

gram number you want to delete (Fig. 25).

Press ON/OFF, then the + button until SKIP is

displayed (Fig. 26). The switch timer will now

suppress this setting.

Press ON/OFF again to cycle through the pro-

gram until the display brieﬂy shows SAVE.

Press MODE to exit from programming and automatically save

your new settings.

NOTE: Repeat this step and select ON or OFF to reactivate the setting.

Revising an ON or OFF Setting

Use these steps to revise an existing ON or OFF setting.

Press MODE until the screen displays ProGraM

below the time of day (Fig. 27).

Press ON/OFF to display the program number,

then press the + button until you see the pro-

gram number you want to revise (Fig. 28).

Press the ON/OFF button as many times as

necessary to display the setting you want to

revise, for example, the MINUTE (Fig. 29).

Now press the + button again to display the

new minute you want to set (Fig. 30).

Press MODE to exit from programming and

automatically save your new settings.

Press ON/OFF to display the program number,

then press + until you see the program num-

ber you want to set (Fig. 14).

Press ON/OFF, then press + if necessary, to

display ON for setting the ON time (Fig. 15).

Continue to press + for OFF (if setting an OFF

time) or SKIP (if deleting a setting).

Press ON/OFF, then press + to display whether you want ON

to be set for DUSK, DAWN, or a speciﬁc time which would be

shown as “12:00” (until you change it).

If ON is to be at Dawn or Dusk:

NOTE: Some people like to set DUSK as an ON time and match it

with a speciﬁc time such as 11:00 pm for OFF.

Press + to display DUSK (Fig. 16). Continue to

press + for DAWN (if setting DAWN as the on

time).

Press ON/OFF to display the days you want

the setting to be active, then press + to select

either ALL days, M-F, WeeKenD, or an indi-

vidual day. Fig. 17 shows ALL as an example.

Press ON/OFF again. The display will brieﬂy show SAVE.

You have successfully set the ON time as DUSK, and must now

repeat this procedure to set the OFF time to go with it.

The display will loop back to Step 2 above, ready

for you to set another program. Press + to dis-

play a ﬂashing “02” (Fig. 18).

To set PROGRAM 2, follow this procedure

again, beginning at Step 2 above.

When you’re ﬁnished, press MODE to exit from programming

and automatically save your new settings.

If ON is to be at a Speciﬁc Time such as 8:15 pm:

Press + to display “12:00” (Fig. 19).

Press ON/OFF to display the hour (Fig. 20), then

press + until the correct hour is shown.

NOTE: If you go too far, press the – to back

up, or press + until you loop back around.

Press ON/OFF to display the minutes (Fig. 21),

then press + until the correct minute is shown.

Press ON/OFF to display the days you want

the setting to be active, then press + to select

either a speciﬁc day of the week, ALL days, M-

F (work week only), or WKD (weekend only).

Fig. 22 shows ALL as an example.

Press ON/OFF again The display will brieﬂy show SAVE.

You have successfully set the ON time to 8:15 pm, and must now

repeat this procedure to set the OFF time to go with it.

The display will loop back to Step 2 above, ready

for you to set another program. Press + to dis-

play a ﬂashing “02” (Fig. 23).

To set PROGRAM 2, follow the procedure be-

ginning at Step 2 on the other side of this sheet. Repeat these

steps to create up to 40 unique ON/OFF settings.

When you’re ﬁnished, press MODE to exit from programming

and automatically save your new settings.

•

If the timer clicks but the load only operates when the re-

mote switch is in one of its 2 positions, you need to turn off

the power at the service panel, then reverse wires “A” and

“B.” You can reverse wires “A” and “B” at the remote switch

wall box, or you can reverse wires “A” and “B” where they

connect to the red and blue wires of the switch timer. Then

turn power back on at the service panel and repeat Step J.

Verify that the controlled load turns on or off each time that the

remote switch is operated. Your timer is now ready to be set.

If a Multiple Switch Timer Setup:

Multi-switch applications using the ST01 Series switch timer are

wired differently than when using conventional toggle switches.

Read the following installation instructions carefully.

Multiple switch timers may be mounted in an unlimited num-

ber of adjacent junction box slots.

No derating is required for multiple switch timers.

For a three-switch setup:

For four or more switch setups:

Use the preceding 3-switch installation diagram and wire 4-way

switches between the two 3-way switches.

NOTE: The remote switch(es) may not function reliably when the

accumulated wire length to the remote switch(es) exceeds 100

feet or if the wiring to the remote switch(es) is buried under-

ground. Contact Intermatic Customer Service for details.

NOTE: Used remote switches from a previous conventional

installation may not function reliably with an electronic timer. Try

a brand new remote switch if function is intermittent.

You are now ready to set the DATE and TIME.

•

ADDITIONAL WIRE

LOAD

NEUTRAL

TWO 3-WAY SWITCHES

RED

BLUE

TIMER

BLACK

LINE

Product specificaties

Merk:	Intermatic
Categorie:	Schakelaar
Model:	ST01

Heb je hulp nodig?

Als je hulp nodig hebt met Intermatic ST01 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Schakelaar Intermatic

Intermatic DT620 Handleiding

11 December 2024

Intermatic DTAV40Q-M Handleiding

11 December 2024

Intermatic DTAV40IM Handleiding

11 December 2024

Intermatic DTAV40E2 Handleiding

11 December 2024

Intermatic DTAV40M Handleiding

11 December 2024

Intermatic P1121 Handleiding

11 December 2024

Intermatic TN311 Handleiding

11 December 2024

Intermatic TN111RM40 Handleiding

11 December 2024

Intermatic P1131 Handleiding

11 December 2024

Intermatic TN111K Handleiding

11 December 2024

Handleiding Schakelaar

Nieuwste handleidingen voor Schakelaar

Smart-AVI SM-DVN-2D Handleiding

21 December 2024

Smart-AVI SM-DPN-2Q Handleiding

21 December 2024

Smart-AVI DVN-16P Handleiding

21 December 2024

Smart-AVI SM-DVN-4D Handleiding

21 December 2024

Smart-AVI SM-EDPN-4S Handleiding

21 December 2024

Smart-AVI SM-EDPN-4D Handleiding

21 December 2024

Smart-AVI SM-EDPN-2Q Handleiding

21 December 2024

Smart-AVI SM-DVN-4S Handleiding

21 December 2024

Smart-AVI SM-UHN-2D Handleiding

21 December 2024

Smart-AVI SM-UHN-2S Handleiding

21 December 2024