Intermatic HB880R Handleiding
Intermatic
Schakelaar
HB880R
Lees hieronder de đ handleiding in het Nederlandse voor Intermatic HB880R (2 pagina's) in de categorie Schakelaar. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
MODEL HB880R
WARNING Risk of Fire or Electrical Shock
⢠Connect only to an outdoor receptacle protected by a Ground Fault
Circuit Interrupter (GFCI).
⢠Connect only to an outdoor receptacle with a âwhile in useâ weatherproof
cover.
⢠Mount at least 24 inches (0.6 meters) above ground level with receptacles
facing downward.
⢠Unplug timer power cord before opening the battery compartment.
⢠Replace battery cover and retaining screw before plugging in timer cord.
⢠Do not use timer if battery cover and/or retaining screw is missing or
damaged.
⢠Do not exceed rated capacity of connected extension cord or timer.
SpeciďŹcations
⢠Input Voltage: 120 VAC, 60 HZ
⢠15 Amps General Purpose
⢠1000 Watts Tungsten
⢠1/2 Horsepower
⢠8.3 Amps Ballast (Standard) (Inductive)
⢠500 VA Electronic Ballast
Description
The HB880R Time Switch is a programmable digital timer for outdoor
applications. Astronomic settings adjust for seasonal changes. Auto-
matic Daylight Saving Time adjustment. Follow these instructions to
complete the programming for the HB880R time switch.
Enable the Battery
1. On the back of timer, pull out the pull tab (if present) from
the battery holder. See Figure 2.
2. Verify that the controller display activates.
3. Take one of these actions.
IF THE DISPLAY THEN...
Activates Go to Setting the Calendar,
Clock and Astro Time
Does not activate Replace Battery. See
Replacing Battery on page 2.
Setting the Calendar, Clock and Astro Time
NOTE: The timer does not have to be plugged in to set the timer.
1. Press DATE/TIME/NEXT. The year îashes.
SELECT
FUNCTION
DATE/TIME
NEXT
SET ON/OFF
EVENTS
RESET
DELETE +-
MO
PM AUTO
AM RD M
DST
ON
OF F
TUWETHFR SASU
7 Day/ 7 Event Outdoor Timer
Pull Tab
Remove st ic prior to usi prpla tape ng oduct.
C ery c tacts i no L display.heck batt on f CD
2. Press or to scroll to the current year, then press + - DATE/
TIME/NEXT. The month digit îashes.
The months start with 01 (Jan) through 12 (Dec).NOTE:
3. Press or to select the current month, then press + - DATE/TIME/
NEXT. The day of the month digit and the corresponding day of
the week îashes.
4. Press or to select the current day of the month and then press + -
DATE/TIME/NEXT.
5. From the DST (Daylight Saving Time) screen, press or to set + -
the DST function to or , then press Auto (ON) OFF DATE/TIME/
NEXT. The hour digit in the current time îashes on the screen.
6. Press or to set the current hour (AM/PM), then press + - DATE/
TIME/NEXT. The minute digit îashes.
7. Press or to set the current minute, then press + - DATE/TIME/
NEXT. A îashing ânorâ and the Astro icon appears.
8. Using the map in Figure 3 as reference, press or to select your+ -
Astro zone then press DATE/TIME/NEXT to save the zone. The
screen appears. AM sunrise
denotes NORTH, denotes CENTER, and NOTE: nor CEN SOU
denotes SOUTH.
9. From the screen, press or to set the sunrise time, AM sunrise + -
then press DATE/TIME/NEXT. The PM Sunset screen appears.
The setting range is a maximum of / 2 hours. NOTE: + -
Press to restore calculated sunrise time.NOTE: DELETE
10. Press or to set the sunset time, then press + - DATE/TIME/
NEXT. The time of day screen (îashing colon) appears.
The setting range is a maximum of / 2 hours fromNOTE: + -
the automatically calculated sunrise time.
Press to restore calculated sunset time.NOTE: DELETE
Setting Events
This section provides instructions for setting pairs of ON/OFF events.
To set an event pair, you must îrst set the ON event and then repeat
the procedure to set the OFF event. You can set up to seven pairs
of ON/OFF events (14 total) in the timer. Follow this procedure to set
timer events.
1. Press . Dashed lines appear to indicate noSET ON/OFF EVENTS
event is set for the event number.
2. Press DATE/TIME/NEXT to set an ON event. The screen
displays 1200 AM 1 ON (for ON event 1).
3. Press + or - to scroll to the days of the week that the event will run.
To set the event to run every: NOTE:
- Week: Select MO, TU, WE, TH, FR, SA, SU
- Weekday: Select MO, TU, WE, TH, FR
- Weekend: Select SA, SU
Press DATE/TIME/NEXT. The hour îashes.
4. Press or to scroll to the desired hour or Sunrise or + - AM PM
Sunset for the event.
The hour can be set with the 12-hour AM/PM format or atNOTE:
Sunrise or Sunset.
MO
PM AUTO
AM RDM
DST
ON
OFF
TUWE TH FRSA SU
nor
(NORTH)
CEN
(CENTER)
SOU
(SOUTH)
Figure 1
The HB880R Time Switch
Figure 2
Removing pull tab from battery holder
Figure 3
Astro zone map
Outdoor 7 Day
Digital Timer
Operating and User Instructions
MO
PM AUTO
AM RDM
DST
ON
TU WE TH FRSA SU
TABLE 1. Description of Modes
Mode Description
AUTO Switches ON/OFF events at programmed times.
RDM
(Random)
Varies each event up to 30 minutes from the
programmed time
MANUAL Programmed events are ignored but are saved in
memory.
6. When the modiîcations are complete, press SET ON/OFF
EVENTS to scroll through all 7 ON/OFF events (including blank
events) and return to the time of day screen (îashing colon).
Deleting an Event
Follow this procedure to delete an event.
1. Press SET ON/OFF EVENTS to scroll to the unwanted ON
or OFF event.
2. Press DELETE. The screen displays dashes to indicate the
ON or OFF event is deleted.
If necessary, repeat this procedure to delete both NOTE:
ON and OFF settings for the event.
3. When the modiîcations are complete, press SET ON/OFF
to scroll through all 7 ON/OFF events (including blank EVENTS
events) and return to the time of day screen (îashing colon).
Resetting the Timer
In case of a time malfunction or to delete all previous settings, the
unit can be reset.
To reset the timer, use a pen or blunt object to Press . The RESET
timer resets and deletes all the settings in the unit.
Replacing the Battery
One AA size alkaline battery is needed to complete this procedure.
1. Unplug the timer power cord.
2. From the rear of the timer, remove the retaining screw and
battery cover.
3. Install the new AA battery (observe polarity).
4. Verify that the controller display activates.
5. Take one of these actions.
IF THE DISPLAY... THEN...
Activates Go to step 6.
Does not activate, Make sure the battery is not dead and
is installed with the proper polarity.
Adjust as needed to get the screen to
activate.
6. Replace the battery cover and retaining screw.
7. Go to Setting the Calendar, Clock and Astronomic Time.
If the timer is going to be stored for an extended NOTE:
period of time, it is recommended to remove the battery to
preserve the life of the battery.
TABLE 2. Selecting Operating Mode.
Mode Description
ON Load is ON permanently in MANUAL mode.
ON AUTO AUTO has been selected, load is ON, and
will stay ON until the next scheduled OFF
event.
ON RDM RDM mode has been selected, load is ON,
and will stay ON until the next scheduled
RDM OFF event
OFF Load is OFF permanently in MANUAL mode
OFF AUTO AUTO mode is selected, load is OFF, and will
stay OFF until the next scheduled ON event.
5. Take one of these actions.
IF YOU SELECTED... THEN...
A speciîc hour, Go to step 6.
Sunrise or Sunset, Press SET ON/OFF EVENTS
to advance to setting OFF
time for event and go to step 8.
6. Press DATE/TIME/NEXT. The minute digit îashes.
7. Press or to set the minute for the event.+ -
8. Press to set the OFF Event. DashedSET ON/OFF EVENTS
lines appear to indicate no event is set for the event number.
9. Press DATE/TIME/NEXT. The screen displays 12:00 AM 1
OFF (OFF Event 1).
10. Press or + - to scroll to the days of the week that the program will run.
11. Press DATE/TIME/NEXT. The hour îashes.
12. Press + - or to scroll to the desired hour or AM Sunrise or PM
Sunset for the event.
13. Take one of these actions.
IF YOU SELECTED... THEN...
A speciîc hour, Go to step 14
Sunrise or Sunset, Go to step 16
14. Press DATE/TIME/NEXT. The minute digit îashes.
15. Press or to set the minute for the event.+ -
16. If you want to set another ON/OFF pair, repeat steps 1 to 16.
17. If you are înished setting events, press and hold SET ON/OFF
EVENTS until the time of day screen appears.
If you leave the timer idle in Calendar or Event setting NOTE:
modes for 5 minutes, the timer will automatically switch to AUTO
operating mode after saving your settings.
Daily Operation
Once the initial settings are completed, follow this procedure
to select the operation mode in the timer.
1. Press SELECT FUNCTION to scroll to the desired operation
mode. See Table 2 for selection of modes.
In order for the time switch to run the programmed NOTE:
events, the operation mode must be set to or .AUTO RDM
Reviewing or Modifying an Event
Follow this procedure to modify an event.
1. Press SET ON/OFF EVENTS to scroll to the desired event.
2. Press DATE/TIME/NEXT to select the event setting that
you want to modify.
3. Press + - DATE/TIME/ or to adjust the setting, then press
NEXT to save and advance to the next setting.
4. Repeat step 3 as needed for this event.
5. If you want to modify another event, press SET ON/OFF
EVENTS to scroll to the desired event.
Warranty service is available by either (a) returning the product to the dealer from whom the unit was
purchased or (b) completing a warranty claim online at www.intermatic.com. This warranty is made by:
Intermatic Incorporated, 1950 Innovation Way, Suite 300, Libertyville, IL 60048. For additional product or
warranty information go to: http://www.Intermatic.com or call 815-675-7000.
158--02241REF
Troubleshooting
Symptom Possible Cause Solution
The timer is losing settings Low battery not holding memory Replace the battery. See Replacing the
Battery.
Output does not switch or output switches
at wrong time
Auto or RDM mode is not properly
selected.
Select the desired mode. See Daily
Operation.
There are extra or incorrect event settings. Press to scroll SET ON/OFF EVENTS
through the events to înd the event that
needs to be changed or deleted.
See .Reviewing or Modifying an Event
Astro Events have seasonally adjusted
beyond îxed time.
Make sure the îxed timed events are not
set anywhere in the range of earliest to
latest sunrise and sunset.
Product specificaties
| Merk: | Intermatic |
| Categorie: | Schakelaar |
| Model: | HB880R |
Heb je hulp nodig?
Als je hulp nodig hebt met Intermatic HB880R stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Schakelaar Intermatic
11 December 2024
11 December 2024
11 December 2024
11 December 2024
11 December 2024
11 December 2024
11 December 2024
11 December 2024
11 December 2024
11 December 2024
Handleiding Schakelaar
- Schakelaar Bosch
- Schakelaar Philips
- Schakelaar HP
- Schakelaar IKEA
- Schakelaar Panasonic
- Schakelaar Huawei
- Schakelaar Asus
- Schakelaar Honeywell
- Schakelaar Yamaha
- Schakelaar Abus
- Schakelaar Alcatel
- Schakelaar Alecto
- Schakelaar Alpine
- Schakelaar Ansmann
- Schakelaar Apc
- Schakelaar Audiovox
- Schakelaar B-tech
- Schakelaar Basetech
- Schakelaar Behringer
- Schakelaar Belkin
- Schakelaar Berker
- Schakelaar Boss
- Schakelaar Brennenstuhl
- Schakelaar Buffalo
- Schakelaar D-Link
- Schakelaar Digitus
- Schakelaar Eaton
- Schakelaar EBERLE
- Schakelaar Ebode
- Schakelaar Edimax
- Schakelaar Elektrobock
- Schakelaar Elro
- Schakelaar Emerson
- Schakelaar Eminent
- Schakelaar Engenius
- Schakelaar Extech
- Schakelaar Finder
- Schakelaar Flamingo
- Schakelaar GAO
- Schakelaar Generac
- Schakelaar Gira
- Schakelaar Goobay
- Schakelaar Grandstream
- Schakelaar Grasslin
- Schakelaar Hager
- Schakelaar Hama
- Schakelaar Hikvision
- Schakelaar Inverto
- Schakelaar Kathrein
- Schakelaar KlikaanKlikuit
- Schakelaar Konig
- Schakelaar Kopp
- Schakelaar Lancom
- Schakelaar LevelOne
- Schakelaar Linksys
- Schakelaar Logilink
- Schakelaar Manhattan
- Schakelaar Marmitek
- Schakelaar Mercury
- Schakelaar Merlin Gerin
- Schakelaar Mikrotik
- Schakelaar Monacor
- Schakelaar Nedis
- Schakelaar Netgear
- Schakelaar Paladin
- Schakelaar PCE
- Schakelaar Perel
- Schakelaar Plantronics
- Schakelaar Powerfix
- Schakelaar Profile
- Schakelaar Provision ISR
- Schakelaar Pyle
- Schakelaar QNAP
- Schakelaar Renkforce
- Schakelaar Rex
- Schakelaar Robbe
- Schakelaar Schneider
- Schakelaar SEC24
- Schakelaar Shimano
- Schakelaar Silvercrest
- Schakelaar Smartwares
- Schakelaar Speaka
- Schakelaar Suevia
- Schakelaar Sygonix
- Schakelaar Sylvania
- Schakelaar Tenda
- Schakelaar Tesla
- Schakelaar Theben
- Schakelaar Tiptel
- Schakelaar Toolcraft
- Schakelaar Tork
- Schakelaar TP Link
- Schakelaar Trendnet
- Schakelaar Triax
- Schakelaar Trotec
- Schakelaar Unify
- Schakelaar UPM
- Schakelaar Velleman
- Schakelaar Vivanco
- Schakelaar WHALE
- Schakelaar Worx
- Schakelaar ZyXEL
- Schakelaar Jabra
- Schakelaar Jung
- Schakelaar Omnitronic
- Schakelaar One For All
- Schakelaar Clas Ohlson
- Schakelaar CSL
- Schakelaar Monoprice
- Schakelaar Steren
- Schakelaar DoorBird
- Schakelaar Ubiquiti Networks
- Schakelaar EMOS
- Schakelaar Kaiser
- Schakelaar Cotech
- Schakelaar Atlona
- Schakelaar Hamlet
- Schakelaar Comet
- Schakelaar Vivolink
- Schakelaar Techly
- Schakelaar SIIG
- Schakelaar Merten
- Schakelaar Tripp Lite
- Schakelaar Chacon
- Schakelaar Nexa
- Schakelaar Dormakaba
- Schakelaar SPC
- Schakelaar Cisco
- Schakelaar Victron Energy
- Schakelaar Delta Dore
- Schakelaar Vemer
- Schakelaar Matrox
- Schakelaar Gefen
- Schakelaar Ei Electronics
- Schakelaar Fibaro
- Schakelaar GEV
- Schakelaar Juniper
- Schakelaar Planet
- Schakelaar Chamberlain
- Schakelaar Intellinet
- Schakelaar CyberPower
- Schakelaar SunBriteTV
- Schakelaar Lindy
- Schakelaar IOGEAR
- Schakelaar Black Box
- Schakelaar IFM
- Schakelaar DataVideo
- Schakelaar Wago
- Schakelaar Totolink
- Schakelaar Dahua Technology
- Schakelaar AV:link
- Schakelaar PreSonus
- Schakelaar Mercusys
- Schakelaar Elation
- Schakelaar EVE
- Schakelaar Audac
- Schakelaar Vacmaster
- Schakelaar ATen
- Schakelaar RGBlink
- Schakelaar PAC
- Schakelaar Wentronic
- Schakelaar Adder
- Schakelaar Homematic IP
- Schakelaar Extron
- Schakelaar AMX
- Schakelaar OSD Audio
- Schakelaar Equip
- Schakelaar Crestron
- Schakelaar ORNO
- Schakelaar Aeon Labs
- Schakelaar Electro Harmonix
- Schakelaar StarTech.com
- Schakelaar PureLink
- Schakelaar Advantech
- Schakelaar Smart-AVI
- Schakelaar Brilliant
- Schakelaar Kramer
- Schakelaar Micro Connect
- Schakelaar KanexPro
- Schakelaar Intelix
- Schakelaar Blustream
- Schakelaar Avocent
- Schakelaar Shelly
- Schakelaar ICasa
- Schakelaar Vimar
- Schakelaar Kemo
- Schakelaar H-Tronic
- Schakelaar Legrand
- Schakelaar Kraus & Naimer
- Schakelaar Noble
- Schakelaar Intertechno
- Schakelaar Ecler
- Schakelaar Rule
- Schakelaar CYP
- Schakelaar Phoenix Contact
- Schakelaar Seuthe
- Schakelaar Maclean Energy
- Schakelaar SmartAVI
- Schakelaar DEHN
- Schakelaar Cudy
- Schakelaar Heitronic
- Schakelaar Noark
- Schakelaar Cooking Performance Group
- Schakelaar Ernitec
- Schakelaar Adviti
- Schakelaar Flic
- Schakelaar IB Connect
- Schakelaar Liberty
- Schakelaar Alfatron
- Schakelaar Cambium Networks
- Schakelaar 2USB
- Schakelaar Roline
- Schakelaar KVM-TEC
- Schakelaar BZBGear
- Schakelaar STI
- Schakelaar Epiphan
- Schakelaar Mach Power
- Schakelaar Axing
- Schakelaar Raritan
- Schakelaar ConnectPro
- Schakelaar Atlantis Land
- Schakelaar Pizzato Elettrica
- Schakelaar Baco
- Schakelaar SEADA
- Schakelaar Doepke
- Schakelaar IPGARD
- Schakelaar Setti+
Nieuwste handleidingen voor Schakelaar
21 December 2024
21 December 2024
21 December 2024
21 December 2024
21 December 2024
21 December 2024
21 December 2024
21 December 2024
21 December 2024
21 December 2024