Intermatic ET9232 Handleiding

Intermatic Niet gecategoriseerd ET9232

Lees hieronder de 📖 handleiding in het Nederlandse voor Intermatic ET9232 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 5 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

ET9232 Ethernet Module

Ethernet Module Replacement Instructions

MODEL ET9232

• Turnpoweroffatmainpanelbeforeservicingthisswitchortheequipmentitcontrols.

• Morethanonedisconnectswitchmayberequiredtode-energizetheequipmentbeforeservicing.

WARNING

Keeplow-voltagewiringseparatefromhigh-voltagewiring,includingdeadfrontmaterialbetweenwiringareas.Separate

conduitmaybeusedforlow-voltagewiringifnolinevoltagewiringispresent.

Risk of Fire or Electric Shock

Ethernet Module Replacement Guidelines

There are separate Ethernet Module replacement instructions for the one and two circuit time

switches and the 4 to 16 circuit time switches. Be sure to follow the applicable Ethernet Module

replacement instructions for your ET90000 time switch.

ReplacingEthernetModuleon1or2CircuitTimeSwitch

Follow the instructions below to replace an Ethernet Module on a 1 or 2 circuit ET90000 time switch.

1. Disconnect power to the time switch.

2. Open the time switch enclosure cabinet door.

3. At the bottom of the time switch, disconnect the Ethernet cable from the port in the Ethernet

module plastic enclosure.

4. Disconnect the Ethernet module ribbon cable connector plug from the terminal connector.

5. Remove the rivets that secure the Ethernet Module and remove the module from the plastic insulator.

6. Dispose of the rivets and module.

7. Align the new Ethernet module plastic enclosure over the holes on the plastic insulator and

secure the plastic enclosure with the rivets provided with the new module.

8. Connect the ribbon cable connector plug to the terminal connector.

9. Insert the Ethernet cable into the Ethernet port in the enclosure.

10. Close the time switch enclosure door.

11. Return power to the time switch.

CAUTION Risk of Unintended Equipment Operation

Figure 1. ET90000 with Ethernet Module components shown

Terminal

Connector

Ribbon

Cable

Ethernet

Cable port

Rivet (2)

Ethernet Module

Plastic Enclosure

ReplacingEthernetModuleon4to16CircuitTimeSwitch

Follow the instructions below to replace an Ethernet Module on a 4 to 16 circuit ET90000 time switch.

1. Disconnect power to the time switch.

2. Open the time switch enclosure door.

3. Remove the screws from the deadfront and remove the deadfront from the enclosure. Set aside

the deadfront and screws for re-use.

4. Remove the screw that secures the time switch controller door assembly. Set aside the screw

for re-use.

Deadfront Screws

Deadfront

Figure 2. Removing the deadfront.

Figure 3. Time switch controller door assembly with screw.

5. On the inside of the door assembly, disconnect the Ethernet cable from the module.

6. Disconnect the Ethernet module ribbon cable connector plug from the applicable terminal

connector.

7. Remove the three screws that secure the Ethernet Module and remove the module from inside

of the door assembly. Set aside the screws for re-use.

8. Open the new ET9232 Ethernet module plastic enclosure and remove the board.

9. Discard the plastic enclosure.

10. Remove and discard the ribbon cable from the Ethernet module board.

11. Align the module board over the holes on the door assembly and secure the board with the

screws previously removed in step 7.

12. Connect the ribbon cable connector plug to the applicable terminal connector. See Figure 4.

13. Insert the Ethernet cable into the Ethernet port on the module.

14. Close the door assembly and secure with the screw previously removed in step 4.

15. Return the deadfront to the enclosure and secure with the screws previously removed in step 3.

16. Close the time switch enclosure door.

17. Return power to the time switch.

Figure 4. Removing the Ethernet Module.

Figure 5. Ethernet module plastic enclosure.

Product specificaties

Merk:	Intermatic
Categorie:	Niet gecategoriseerd
Model:	ET9232

Heb je hulp nodig?

Als je hulp nodig hebt met Intermatic ET9232 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Intermatic

Intermatic ET9232 Handleiding

11 December 2024

Intermatic EI500WC Handleiding

11 December 2024

Intermatic 2T2500GA Handleiding

11 December 2024

Intermatic T101PC Handleiding

5 September 2024

Intermatic T103 Handleiding

5 September 2024

Intermatic T103PC Handleiding

5 September 2024

Intermatic T104PC Handleiding

5 September 2024

Intermatic T104 Handleiding

6 Januari 2024

Intermatic ET8015C Handleiding

16 November 2023

Intermatic ET8215C Handleiding

16 November 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Philips AquaClean CA6903 Handleiding

11 December 2024

Schneider RE22R1MAMR Handleiding

11 December 2024

Wachendorff MA964802 Handleiding

11 December 2024

EBERLE MRU 1 Handleiding

11 December 2024

Mean Well PWM-200-12 Handleiding

11 December 2024

Western Co. WR20 Handleiding

11 December 2024

WEG MPW18-3-U004 Handleiding

11 December 2024

WEG MPW18-3-U001 Handleiding

11 December 2024

WEG MPW12-3-D016S Handleiding

11 December 2024

WEG MPW40-3-U032 Handleiding

11 December 2024