Interlogix TX-E721 Handleiding

Interlogix Bewegingsdetector TX-E721

Lees hieronder de 📖 handleiding in het Nederlandse voor Interlogix TX-E721 (4 pagina's) in de categorie Bewegingsdetector. Deze handleiding was nuttig voor 72 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

P/N - 1 4 466 5305 • Rev A • 11APR17 /

TX-E721 Fresnel Lens Pet Immune PIR

Description

This is the Installation Sheet for the TX-E721 Fresnel Lens Pet Immune PIR

A motion sensor (passive-infrared or PIR) detects movement within a

speciﬁc area by sensing the infrared energy emitted from a body as it

moves across the sensor’s field of view. When this motion is detected, the

sensor transmits an alarm signal to the control panel.

Figure 1 Pet Immune SAW PIR Motion Sensors :

Use these motion sensors to protect locations where door/window sensors

are impractical or not needed. For example, use a motion sensor to protect

large areas or open ﬂoor plans. Motion sensors also provide backup

protection for door/window sensors.

The Pet Immune -E721 utilizes advanced signal processing, a new TX

custom designed lens, and a new custom designed sensing element. The

combination of these improvements provides false alarm immunity for pets

with a combined weight of up to 40 pounds while still providing superior

human catch performance.

These wireless motion sensors include the following features:

• 35 by 40 ft. (10.6 m by 12 m) coverage area.

• Three minute transmitter lockout time after an alarm that helps extend

battery life.

• Cover-activated tamper

• Supervisory signals transmitted every 64 minutes to the control panel.

• Sensor low battery reports (trouble) to the control panel.

• Field-selectable sensitivity options.

Installation

Installation Guidelines

• Temporarily place the sensor in its intended mounting location.

Program and ﬁnal test the sensor before permanently mounting it.

• If possible, locate sensors within 100 ft. (30.5 m) of the panel. While a

transmitter may have a range of 500 ft. (152 m) or more out in the

open, the environment at the installation site can have a signiﬁcant

eﬀect on transmitter range. Sometimes a change in sensor location

can help overcome adverse wireless conditions.

• The recommended mounting height is 7 1/2 ft.

• Position the sensor to protect an area where an intruder would be most

likely to walk across the detection pattern See Figure 2.

Figure 2: Overhead Detection Path

• Mount the motion sensor on a rigid surface which is free from

vibrations.

• Do not mount the sensor near duct work or other large metallic

surfaces which may aﬀect the RF signals (see RF Testing). Actual

acceptable transmitter range should be veriﬁed for each installation.

• Mount the sensor permanently on a ﬂat wall or in a corner. Do not set it

on a shelf.

• Windows should be closed in any area which has an armed motion

sensor.

• The sensor must be incline-mounted at a mounting height of 7.5 ft. See

Figure 3.

Figure 3: Wall Mount Options

• Room temperature must be kept between 60° and 120°F (16° and 49°

C).

• Position the sensor so it faces a solid reference point, like a wall.

Programming

Refer to the panel documentation for information on programming the

sensor into the panel.

To Trip the Sensor

1. Set the panel to program mode.

2. Proceed to the Learn Sensors menu.

2 4 -E721 PET Immune PIR Motion Detector Installation Sheet/ TX

3. Remove the PIR from its mounting plate (activating the tamper switch).

4. Select the appropriate sensor group and number.

5. Exit the panel’s programming mode.

6. Return the PIR to its mounting plate.

Final Testing

Final testing should be done to verify radio signal integrity and conﬁrm

control panel programming and response. The actual transmitter range can

be determined by performing a sensor test as follows:

1. With the PIR temporarily mounted at its intended location, remove the

PIR from its mounting plate and activate the tamper switch to start the

walk test mode.

2. Replace the sensor in its mounting plate.

3. Place the control panel in Sensor test mode. Move across the

detection pattern until the sensor’s LED turns on. STOP your motion.

4. Listen for the appropriate system response. Refer to the speciﬁc panel

installation manual for details on system response. If the system does

not respond as expected, proceed to the section. “ ”Troubleshooting

Mounting

The sensors must be incline-mounted on a wall surface or incline-mounted

in a corner at a mounting height of 7.5 ft. (2.5 m).

To Mount the Sensor

1. Remove the mounting plate by depressing the button on the top of the

sensor body. With the opposite hand pull the mounting plate away from

the body of the sensor.

2 Punch out the mounting holes that best ﬁt your application. See Figure

3 for wall mount options.

3. See Figure 4 to determine which knockouts to use when mounting the

motion sensor. Use the outside 4 holes for corner mounting, or the

inside 4 holes for surface mounting.

Figure 4: PIR Mounting Plate Knockouts

4. Mark the location of the required holes on the mounting surface.

5. Use wall anchors and screws to secure into place. Attach the sensor to

the mounting plate.

6. When testing is completed the PIR can be securely attached to its

mounting plate by screwing the smallest enclosed screw into the hole

at the top of the mounting plate.

Setting the Sensitivity

The PIR has two sensitivity settings (standard and high sensitivity). The

sensor is set to standard sensitivity at the factory. This sensitivity is

preferred for most applications and provides the best immunity to false

alarms.

Note: If the shorting jumper is not used or is placed incorrectly, the sensor

defaults to standard sensitivity.

Figure 5: Sensitivity Pin Locations

CAUTION: High sensitivity should only be used in environments where

the room temperature is very stable.

ATTENTION: La haute sensibilité ne doit être utilisée que dans des

environnements où la température ambiante est très stable

1. Remove the mounting plate by depressing the button on the top of the

sensor body. With the opposite hand pull the mounting plate away from

the body of the sensor.

2. Locate the sensitivity pins directly above the battery when looking at

the back of the PIR

3. To change to high sensitivity, move the shorting jumper to the pair of

pins that are closer to the left side of the PIR

4. Walk test the PIR to verify the sensitivity.

The diﬀerence between the two settings are indicated in Figures 6 and

7.below.

Figure 6: Standard Sensitivity Setting

Figure 7: High Sensitivity Setting

TX-E721 PET Immune PIR Motion Detector Installation Sheet 3 4 /

Important information Regarding Sensitivity Settings

The sensitivity settings should be set as followed:

Standard Sense:

 Rooms < 25ft

 Pets 40 pounds <

High Sense:

 Rooms < 35ft

 Pets 20 pounds <

Testing

Walk Testing

Walk testing should be done to determine the sensor’s actual coverage

area. The edge of the coverage pattern is determined by the first ﬂash of the

LED. This may change slightly depending upon the sensitivity setting. Walk

test the unit from both directions to determine the pattern boundaries.

CAUTION: Excessive use of the walk test mode may reduce battery

life. Use only for initial setup and maintenance testing.

ATTENTION : L'utilisation excessive du mode test de marche peut

réduire la durée de vie de la batterie. Utiliser uniquement pour la

conﬁguration initiale et les tests de maintenance.

1. Remove the sensor body from the mounted mounting plate and then

remount the body to activate the 60 second walk test mode.

2. Walk across the coverage pattern to determine the coverage area,

indicated by LED activation. Each activation extends the walk test

mode for an additional 60 seconds.

After 60 seconds without motion the walk test mode and the LED will no

longer activate when motion is detected.

Note: When the walk test mode has ended, an alarm can be transmitted

only after 3 minutes have passed since the previous alarm. This 3 minute

lockout time reduces unnecessary RF transmissions in high traﬀic areas

thereby extending battery life.

Environment Testing

Turn on all heating or air conditioning sources which would normally be

active during the protection period. Stand away from the sensor and outside

the coverage pattern and watch for alarms. When testing the Pet Immune

PIR also verify the pets allowed in the coverage pattern do not trip the PIR.

Maintenance

At least once a year, the range and coverage should be veriﬁed for proper

operation. The end user should be instructed to put the sensor in walk test

mode and walk through the far end of the coverage pattern to verify proper

detection.

Replacing the Battery

When the system indicates the sensor has a low battery, replace the battery

immediately.

1. Remove the mounting plate by depressing the button on the top of the

sensor body. With the opposite hand pull the mounting plate away from

the body of the sensor. See Figure 8.

2. Remove the old battery and replace with new battery (CR123A)

Note: Observe polarity when replacing the battery The battery should .

be inserted with the negative end closest to the left side of the PIR

when viewing it from the back. The positive end of the battery should

be closest to the right side. See Figure 8.

If a battery is installed incorrectly the unit will not function and

the red LED will not light up. The sensor may be damaged if a

battery is installed incorrectly.

3. Dispose of the battery as required by local requirements

4. Walk test the PIR to verify proper operation.

Note: When the battery is replaced, wait at least three minutes after

installing the battery before activating the walk test mode.

Figure 8: PIR Components, Battery Locations & Tamper Switch

Troubleshooting

Use the following guidelines if the system does not respond correctly when

the sensor final testing is conducted.

• Check programming and re-program sensor into panel if necessary.

• Move the sensor to another location and test for correct response.

• Check the mounting height and angle are according to “Mounting”

section.

To Relocate a Sensor

1. Test the sensor a few inches from the original position.

2. Increase the distance from the original position and retest until an

acceptable location is found.

3. Mount the sensor in the new location.

4. If no location is acceptable, test the sensor as described below:

• Test a known good sensor at the same location.

• If the system does not respond, avoid mounting a sensor at that

location.

• If the replacement sensor functions, return the problem sensor for

repair or replacement.

Speciﬁcations

TX-E 721

RF Frequency

319.5 MHz

Compatibility

Interlogix 319.5 MHz control panels/receivers

Battery Type

CR123A

Typical Battery Life

Up to 5 years at 68° F (20° C)

Operating

Temperature Range

32° to 110°F (0° to 43°C) Non-pet

applications

60° to 110°F (16° to 43°C) Pet applications

Supervisory Interval

64 Minutes

Relative Humidity

0 – 90% non-condensing

Storage Temperature

Range

-30 to 140°F (-34 to 60°C)

Dimensions

(L x W x H)

2.5 in x 2.1 in x 3.0 in

Product specificaties

Merk:	Interlogix
Categorie:	Bewegingsdetector
Model:	TX-E721
Kleur van het product:	Wit
Breedte:	64 mm
Diepte:	53 mm
Hoogte:	76 mm
Connectiviteitstechnologie:	Draadloos
Montagewijze:	Muur
Type stroombron:	Batterij/Accu
Certificering:	ETL Listed
Type beeldsensor:	Passieve infraroodsensor (PIR)
Temperatuur bij opslag:	-34 - 60 °C
Frequentie:	319.5 MHz
Bedrijfstemperatuur (T-T):	16 - 43 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 90 procent
Huisdierimmuniteit (max):	18.1437 kg