Inovonics EN1215WEOL Handleiding

Inovonics Deur-/raamsensor EN1215WEOL

Lees hieronder de 📖 handleiding in het Nederlandse voor Inovonics EN1215WEOL (2 pagina's) in de categorie Deur-/raamsensor. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

8/22/19 357-05043-02 Rev A © Inovonics, 2019 - www.inovonics.com

EN1215WEOL Door/Window with Wall

Tamper and EOL

Installation Instructions

1 Overview

The Inovonics EN1215WEOL door/window with wall tamper and

EOL has a built-in magnetic reed switch on the side, with a

magnet that supports a 5/8" inch gap. The magnetic reed switch

can be used with both ferrous and non-ferrous material. A 2.2K

ohm end of line resistor is included with the EN1215WEOL, and

is required for operation.

The EN1215WEOL includes a back tamper switch. The tamper

condition must be defined within the control panel as a trouble

condition when the system is disarmed, and as an alarm

condition when the system is armed.

The door/window with wall tamper and EOL is available in North

America, Australia and New Zealand; the radio frequency band

has been configured for the appropriate geographic area at the

factory.

Note: For UL installations, refer to the EN4216MR Installation

and Operation Manual, the EN4232MR Installation and

Operation Manual, or the EN7290 EchoStream Receiver/

Interface for Honeywell VISTA Panels Installation Instructions.

The switch contact must also be located in the same room as the

EN1215WEOL, and the EN1215WEOL must be installed in

accordance with UL 681 and ULc S302.

Note: The cable length from the switch contact must not to

exceed 10 feet.

Caution: The EN1215WEOL contains both a wired input and an

input activated by a reed switch and magnet. The reed switch

and magnet must be used unless the application specifically

supports both inputs as separate devices. Use of the wired input

is optional.

1.1 Inovonics Contact Information

If you have any problems with this procedure, contact Inovonics

Wireless technical services:

• E-mail: support@inovonics.com.

• Phone: (800) 782-2709.

1.2 EN1215WEOL Internal Components

Figure 1 Door/window with wall tamper and EOL internal

components

1.3 What’s In The Carton

• Two wall mount screws.

• Two wall mount anchors.

• Two selection jumpers.

• One 3.0V lithium battery.

• One housing closure screw.

• One magnet.

• One 2.2K ohm end of line resistor.

2 Installation and Startup

2.1 Installation Notes

• These products are designed to be installed and maintained

by professional security technicians.

• Products are intended for indoor use.

• Manually test all products weekly.

2.2 Battery Installation

1. Use your thumb to press the housing release tab on the

bottom of the transmitter; separate the housing.

2. Install the battery.

3. Press the reset button to initialize the transmitter.

4. Test the transmitter and ensure appropriate response.

2.3 Select Input Type and Wire Resistor

The N/O-N/C selection pins allow the choice of a normally open

or normally closed state for the contact circuit wired to the input

terminal.

The transmitter is shipped set for normally open, with a selection

jumper on the N/O selections pins.

Set for normally open operation:

1. Place a selection jumper on the selection pins to select

normally open.

2. Use 22 AWG wire to wire the 2.2K ohm resistor in parallel

with the N/0 contact per Figure 2. The distance from the

external contact to the EN1215WEOL must not exceed 10

feet (3 meters).

3. Press the reset button to complete configuration.

Figure 2 Wired for N/O operation

Set for normally closed operation:

1. Remove the selection jumper from the selection pins.

2. Use 22 AWG wire to wire the 2.2K ohm resistor in series with

the N/C contact per Figure 3. The distance from the external

contact to the EN1215WEOL must not exceed 10 feet (3

meters).

3. Press the reset button.

Figure 3 Wired for N/C operation

2.4 Register the EN1215WEOL

Transmitters must be registered with the system in order to be

monitored and supervised. When supervised, the transmitter will

send a check-in message to the receiver every three minutes.

Each transmitter has a unique factory-programmed identification

number.

Refer to the system receiver’s documentation for details on

registering the transmitter.

1. When prompted by the receiver to reset transmitter, press

the reset button.

2. Replace the cover.

3. Test the transmitter and ensure appropriate response.

For product and installation videos visit us at

www.inovonics.com/videos or use the QR

code below.

ACombined housing/wall tamper

switch

BN/O - N/C jumper

C DInput terminal Reset button

EWall-mount screw holes FHousing closure screw hole

GReed switch

8/22/19 357-05043-02 Rev A © Inovonics, 2019 - www.inovonics.com

2.5 Mount the EN1215WEOL

1. Choose a mounting location which will allow the magnet to

be located parallel to the transmitter such that there is no

more than a 5/8” gap between it and the internal contact

magnetic reed switch.

2. Route the external wiring through the wall, as shown in

Figure 4.

3. Mount the transmitter to the wall using the wall-mount screw

holes, ensuring the housing is flush against the wall and the

wall tamper switch is firmly depressed.

Figure 4 Mount the Transmitter to the Wall

4. Close the housing.

5. Secure the housing through the enclosed housing screw

hole. Accessing this screw on an active transmitter requires

opening the housing and removing the battery, causing a

tamper condition.

6. Mount the magnet so that it is parallel to the transmitter with

no more than a 5/8” inch gap between it and the internal

contact magnetic reed switch.

3 Specifications

Note: The 2.2K ohm resistor is required to operate the

EN1215WEOL.

External contacts: N/O or N/C.

Distance, external contact to EN1215WEOL: 10 feet (3 meters)

maximum.

Distance, magnet to internal contact magnetic reed switch: 5/8”.

Power requirement: 3VDC, 60 mA.

Typical battery life: 3-5 years.

Battery type (BAT604): Panasonic CR123A.

Operating environment: 0 to 60°C (32 to 140°F), 90% relative

humidity, noncondensing; 0 to 49°C (32 to 120°F) for UL

installations.

UL listings: UL 365, UL 634, ULC/ORD-C634-86, UL 1023, ULC/

ORD-C1023-74, UL 1076, UL 1610.

Compatible receiver: EN4204R, EN4216MR, EN4232MR,

EN7290.

Note: Inovonics supports recycling and reuse whenever

possible. Please recycle these parts using a certified electronics

recycler.

Note: Specifications and data are subject to change without

notice.

4 Television and Radio Interference

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

5 FCC Part 15 and Innovation, Science and

Economic Development Canada (ISED)

Compliance

This device complies with part 15 of the FCC Rules, and ISED

license-exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference

that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR Innovation, Sciences

et Développement économique Canada applicables aux

appareils radio exempts de licence. L'exploitation est autorisée

aux deux conditions suivantes: (1) l'appareil ne doit pas produire

de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout

brouillage radioélectrique subi, même si le brouillage est

susceptible d'en compromettre le fonctionnement.

6 Radiation Exposure Limits

6.1 FCC

This equipment complies with FCC radiation exposure limits set

forth for an uncontrolled environment. In order to avoid the

possibility of exceeding the FCC radio frequency exposure limits,

human proximity to the antenna shall not be less than 20 cm

during normal operation and must not be co-located or operating

in conjunction with any other antenna or transmitter.

6.2 ISED

This equipment complies with ISED RSS-102 radiation exposure

limits set forth for an uncontrolled environment. This transmitter

must be installed to provide a separation distance of at least 20

cm from all persons and must not be co-located or operating in

conjunction with any other antenna or transmitter.

Cet équipement est conforme avec ISED RSS-102 des limites

d'exposition aux rayonnements définies pour un environnement

non contrôlé. Cet émetteur doit être installé à au moins 20 cm de

toute personne et ne doit pas être colocalisé ou fonctionner en

association avec une autre antenne ou émetteur.

Wall

Tamper

Product specificaties

Merk:	Inovonics
Categorie:	Deur-/raamsensor
Model:	EN1215WEOL
Kleur van het product:	Wit
Gewicht:	85 g
Breedte:	46 mm
Diepte:	23 mm
Hoogte:	104 mm
Connectiviteitstechnologie:	Draadloos
Geschikt voor:	Deur/raam
Levensduur van de batterij:	60 maand(en)
Interface:	WLAN
Duurzaamheidscertificaten:	Federal Communications Commission (FCC), RoHS
Frequentie:	902 - 928 MHz
Transmissie-afstand:	3 m
Bedrijfstemperatuur (T-T):	0 - 60 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 90 procent
Aantal producten inbegrepen:	1 stuk(s)
Type batterij:	CR123A